summaryrefslogtreecommitdiffstats
path: root/include/asm-powerpc/rtas.h
Commit message (Collapse)AuthorAgeFilesLines
* [POWERPC] Add rtas_service_present() helperNathan Lynch2006-12-081-0/+1
| | | | | | | | | | | | | | To test for the existence of an RTAS function, we typically do: foo_token = rtas_token("foo"); if (foo_token == RTAS_UNKNOWN_SERVICE) return; Add a rtas_service_present method, which provides a more conventional boolean interface for testing the existence of an RTAS method. Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Move pSeries_mach_cpu_die() into platforms/pseries/hotplug-cpu.cMichael Ellerman2006-12-081-2/+0
| | | | | | | | | | | | Move pSeries_mach_cpu_die() into platforms/pseries/hotplug-cpu.c, this allows rtas_stop_self() to be static so remove the prototype. Wire up pSeries_mach_cpu_die() in the initcall, rather than statically in setup.c, the initcall will still run prior to the cpu hotplug code being callable, so there should be no change in behaviour. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Wrap cpu_die() with CONFIG_HOTPLUG_CPULinas Vepstas2006-12-041-2/+0
| | | | | | | | | | Per email discussion, it appears that rtas_stop_self() and pSeries_mach_cpu_die() should not be compiled if CONFIG_HOTPLUG_CPU is not defined. This patch adds #ifdefs around these bits of code. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Add a helper for calculating RTAS "config_addr" parametersMichael Ellerman2006-08-251-0/+16
| | | | | | | | | | | | | Several RTAS calls take a "config_addr" parameter, which is a particular way of specifying a PCI busno, devfn and register number into a 32-bit word. Currently these are open-coded, and I'll be adding another soon, replace them with a helper that encapsulates the logic. Be more strict about masking the busno too, just in case. Booted on P5 LPAR. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Fix might-sleep warning on removing cpusHaren Myneni2006-08-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Noticing the following might_sleep warning (dump_stack()) during kdump testing when CONFIG_DEBUG_SPINLOCK_SLEEP is enabled. All secondary CPUs will be calling rtas_set_indicator with interrupts disabled to remove them from global interrupt queue. BUG: sleeping function called from invalid context at arch/powerpc/kernel/rtas.c:463 in_atomic():1, irqs_disabled():1 Call Trace: [C00000000FFFB970] [C000000000010234] .show_stack+0x68/0x1b0 (unreliable) [C00000000FFFBA10] [C000000000059354] .__might_sleep+0xd8/0xf4 [C00000000FFFBA90] [C00000000001D1BC] .rtas_busy_delay+0x20/0x5c [C00000000FFFBB20] [C00000000001D8A8] .rtas_set_indicator+0x6c/0xcc [C00000000FFFBBC0] [C000000000048BF4] .xics_teardown_cpu+0x118/0x134 [C00000000FFFBC40] [C00000000004539C] .pseries_kexec_cpu_down_xics+0x74/0x8c [C00000000FFFBCC0] [C00000000002DF08] .crash_ipi_callback+0x15c/0x188 [C00000000FFFBD50] [C0000000000296EC] .smp_message_recv+0x84/0xdc [C00000000FFFBDC0] [C000000000048E08] .xics_ipi_dispatch+0xf0/0x130 [C00000000FFFBE50] [C00000000009EF10] .handle_IRQ_event+0x7c/0xf8 [C00000000FFFBF00] [C0000000000A0A14] .handle_percpu_irq+0x90/0x10c [C00000000FFFBF90] [C00000000002659C] .call_handle_irq+0x1c/0x2c [C00000000058B9C0] [C00000000000CA10] .do_IRQ+0xf4/0x1a4 [C00000000058BA50] [C0000000000044EC] hardware_interrupt_entry+0xc/0x10 --- Exception: 501 at .plpar_hcall_norets+0x14/0x1c LR = .pseries_dedicated_idle_sleep+0x190/0x1d4 [C00000000058BD40] [C00000000058BDE0] 0xc00000000058bde0 (unreliable) [C00000000058BDF0] [C00000000001270C] .cpu_idle+0x10c/0x1e0 [C00000000058BE70] [C000000000009274] .rest_init+0x44/0x5c To fix this issue, rtas_set_indicator_fast() is added so that will not wait for RTAS 'busy' delay and this new function is used for kdump (in xics_teardown_cpu()) and for CPU hotplug ( xics_migrate_irqs_away() and xics_setup_cpu()). Note that the platform architecture spec says that set-indicator on the indicator we're using here is not permitted to return the busy or extended busy status codes. Signed-off-by: Haren Myneni <haren@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Setup RTAS values earlier, to enable rtas_call() earlierMichael Ellerman2006-06-281-0/+3
| | | | | | | | | | | | | | Althought RTAS is instantiated when we enter the kernel, we can't actually call into it until we know its entry point address. Currently we grab that in rtas_initialize(), however that's quite late in the boot sequence. To enable rtas_call() earlier, we can grab the RTAS entry etc. values while we're scanning the flattened device tree. There's existing code to retrieve the values from /chosen, however we don't store them there anymore, so remove that code. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] check firmware state before suspendingDave C Boutcher2006-06-151-0/+1
| | | | | | | | | | Currently the kernel blindly halts all the processors and calls the ibm,suspend-me rtas call. If the firmware is not in the correct state, we then re-start all the processors and return. It is much smarter to first check the firmware state, and only if it is waiting, call the ibm,suspend-me call. Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] powerpc: reorg RTAS delay codeJohn Rose2006-06-091-6/+2
| | | | | | | | | | | | | This patch attempts to handle RTAS "busy" return codes in a more simple and consistent manner. Typical callers of RTAS shouldn't have to manage wait times and delay calls. This patch also changes the kernel to use msleep() rather than udelay() when a runtime delay is necessary. This will avoid CPU soft lockups for extended delay conditions. Signed-off-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] powerpc: Make early debugging configurable via KconfigMichael Ellerman2006-01-111-1/+0
| | | | | | | | | | | | | | | | | This patch adds Kconfig entries to control the early debugging options, currently in setup_64.c. Doing this via Kconfig rather than #defines means you can have one source tree, which is buildable for multiple platforms - and you can enable the correct early debug option for each platform via .config. I made udbg_early_init() a static inline because otherwise GCC is to daft to optimise it away when debugging is off. Now that we have udbg_init_rtas() we can make call_rtas_display_status* static. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] powerpc: sanitize header files for user space includesArnd Bergmann2006-01-091-0/+2
| | | | | | | | | | | | | | | include/asm-ppc/ had #ifdef __KERNEL__ in all header files that are not meant for use by user space, include/asm-powerpc does not have this yet. This patch gets us a lot closer there. There are a few cases where I was not sure, so I left them out. I have verified that no CONFIG_* symbols are used outside of __KERNEL__ any more and that there are no obvious compile errors when including any of the headers in user space libraries. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
* powerpc: Merge remaining RTAS codePaul Mackerras2005-11-031-24/+4
| | | | | | | | | This moves rtas-proc.c and rtas_flash.c into arch/powerpc/kernel, since cell wants them as well as pseries (and chrp can use rtas-proc.c too, at least in principle). rtas_fw.c is gone, with its bits moved into rtas_flash.c and rtas.c. Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] powerpc: move rtas_fw.c out of platforms/pseriesArnd Bergmann2005-11-011-0/+3
| | | | | | | | | | | Cell uses the same code as pSeries for flashing the firmware through rtas, so the implementation should not be part of platforms/pseries. Put it into arch/powerpc/kernel instead. Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* powerpc: Merge machdep.hPaul Mackerras2005-10-191-1/+1
| | | | | | | | | | | | A few things change for consistency between ppc32 and ppc64: idle functions return void; *_get_boot_time functions return unsigned long (i.e. time_t) rather than filling in a struct rtc_time (since that's useful to the callers and easier for pmac to generate); *_get_rtc_time and *_set_rtc_time functions take a struct rtc_time; irq_canonicalize is gone; nvram_sync returns void. Signed-off-by: Paul Mackerras <paulus@samba.org>
* powerpc: Merge in the ppc64 version of the prom code.Paul Mackerras2005-10-061-0/+249
This brings in the ppc64 version of prom_init.c, prom.c and btext.c and makes them work for ppc32. This also brings in the new calling convention, where the first entry to the kernel (with r5 != 0) goes to the prom_init code, which then restarts from the beginning (with r5 == 0) after it has done its stuff. For now this also brings in the ppc32 version of setup.c. It also merges lmb.h. Signed-off-by: Paul Mackerras <paulus@samba.org>
OpenPOWER on IntegriCloud