summaryrefslogtreecommitdiffstats
path: root/include/asm-powerpc/ppc-pci.h
Commit message (Collapse)AuthorAgeFilesLines
* powerpc: Move include files to arch/powerpc/include/asmStephen Rothwell2008-08-041-149/+0
| | | | | | | | | | | | | | from include/asm-powerpc. This is the result of a mkdir arch/powerpc/include/asm git mv include/asm-powerpc/* arch/powerpc/include/asm Followed by a few documentation/comment fixups and a couple of places where <asm-powepc/...> was being used explicitly. Of the latter only one was outside the arch code and it is a driver only built for powerpc. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] iSeries: Call iSeries_pcibios_init from setup_archStephen Rothwell2007-12-111-3/+0
| | | | | Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Make global_phb_number staticStephen Rothwell2007-12-031-1/+0
| | | | | | | since it's not used outside of arch/powerpc/kernel/pci-common.c. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Rewrite IO allocation & mapping on powerpc64Benjamin Herrenschmidt2007-06-141-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This rewrites pretty much from scratch the handling of MMIO and PIO space allocations on powerpc64. The main goals are: - Get rid of imalloc and use more common code where possible - Simplify the current mess so that PIO space is allocated and mapped in a single place for PCI bridges - Handle allocation constraints of PIO for all bridges including hot plugged ones within the 2GB space reserved for IO ports, so that devices on hotplugged busses will now work with drivers that assume IO ports fit in an int. - Cleanup and separate tracking of the ISA space in the reserved low 64K of IO space. No ISA -> Nothing mapped there. I booted a cell blade with IDE on PIO and MMIO and a dual G5 so far, that's it :-) With this patch, all allocations are done using the code in mm/vmalloc.c, though we use the low level __get_vm_area with explicit start/stop constraints in order to manage separate areas for vmalloc/vmap, ioremap, and PCI IOs. This greatly simplifies a lot of things, as you can see in the diffstat of that patch :-) A new pair of functions pcibios_map/unmap_io_space() now replace all of the previous code that used to manipulate PCI IOs space. The allocation is done at mapping time, which is now called from scan_phb's, just before the devices are probed (instead of after, which is by itself a bug fix). The only other caller is the PCI hotplug code for hot adding PCI-PCI bridges (slots). imalloc is gone, as is the "sub-allocation" thing, but I do beleive that hotplug should still work in the sense that the space allocation is always done by the PHB, but if you unmap a child bus of this PHB (which seems to be possible), then the code should properly tear down all the HPTE mappings for that area of the PHB allocated IO space. I now always reserve the first 64K of IO space for the bridge with the ISA bus on it. I have moved the code for tracking ISA in a separate file which should also make it smarter if we ever are capable of hot unplugging or re-plugging an ISA bridge. This should have a side effect on platforms like powermac where VGA IOs will no longer work. This is done on purpose though as they would have worked semi-randomly before. The idea at this point is to isolate drivers that might need to access those and fix them by providing a proper function to obtain an offset to the legacy IOs of a given bus. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Add EEH sysfs blinkenlightsLinas Vepstas2007-06-141-0/+3
| | | | | | | | | | | | | | | | | | Add sysfs blinkenlights for EEH statistics. Shuffle the eeh_add_device_tree() call so that it appears in the correct sequence. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> ---- arch/powerpc/platforms/pseries/Makefile | 2 arch/powerpc/platforms/pseries/eeh.c | 4 + arch/powerpc/platforms/pseries/eeh_cache.c | 2 arch/powerpc/platforms/pseries/eeh_sysfs.c | 84 +++++++++++++++++++++++++++++ arch/powerpc/platforms/pseries/pci_dlpar.c | 7 +- include/asm-powerpc/ppc-pci.h | 3 + 6 files changed, 98 insertions(+), 4 deletions(-) Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Assorted janitorial EEH cleanupsLinas Vepstas2007-05-101-3/+15
| | | | | | | | | | | | | | Assorted minor cleanups to EEH code; -- use literals, use kerneldoc format. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> ---- arch/powerpc/platforms/pseries/eeh.c | 13 ++++++++++--- arch/powerpc/platforms/pseries/eeh_driver.c | 7 ++++--- include/asm-powerpc/ppc-pci.h | 18 +++++++++++++++--- 3 files changed, 29 insertions(+), 9 deletions(-) Signed-off-by: Paul Mackerras <paulus@samba.org>
* Fix occurrences of "the the "Michael Opdenacker2007-05-091-1/+1
| | | | | Signed-off-by: Michael Opdenacker <michael@free-electrons.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
* [POWERPC] EEH: wait for slot statusLinas Vepstas2007-03-221-1/+2
| | | | | | | | | | Modify routine that returns PCI slot status to wait for slot status to become available. This is needed, as slots that are in some remote card cage may go offline for extended periods of time. New users for this routine in following patches. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Make find_and_init_pbs() a void functionStephen Rothwell2007-03-091-1/+1
| | | | | | | It always returned 0 and noone checked. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Allow pSeries to build without CONFIG_PCIStephen Rothwell2007-03-091-0/+7
| | | | | Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Generic OF platform driver for PCI host bridges.Benjamin Herrenschmidt2006-12-041-6/+6
| | | | | | | | | | | | | | | | | When enabled in Kconfig, it will pick up any of_platform_device matching it's match list (currently type "pci", "pcix", "pcie", or "ht" and setup a PHB for it. Platform must provide a ppc_md.pci_setup_phb() for it to work (for doing the necessary initialisations specific to a given PHB like setting up the config space ops). It's currently only available on 64 bits as the 32 bits PCI code can't quite cope with it in it's current form. I will fix that later. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Make pci_read_irq_line the defaultBenjamin Herrenschmidt2006-12-041-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | This patch reworks the way IRQs are fixed up on PCI for arch powerpc. It makes pci_read_irq_line() called by default in the PCI code for devices that are probed, and add an optional per-device fixup in ppc_md for platforms that really need to correct what they obtain from pci_read_irq_line(). It also removes ppc_md.irq_bus_setup which was only used by pSeries and should not be needed anymore. I've also removed the pSeries s7a workaround as it can't work with the current interrupt code anyway. I'm trying to get one of these machines working so I can test a proper fix for that problem. I also haven't updated the old-style fixup code from 85xx_cds.c because it's actually buggy :) It assigns pci_dev->irq hard coded numbers which is no good with the new IRQ mapping code. It should at least use irq_create_mapping(NULL, hard_coded_number); and possibly also set_irq_type() to set them as level low. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] EEH: enable MMIO/DMA on frozen slotLinas Vepstas2006-09-211-0/+11
| | | | | | | | Add wrapper around the rtas call to enable MMIO or DMA on a frozen pci slot. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] powerpc: properly configure DDR/P5IOC children devsJohn Rose2006-03-161-0/+1
| | | | | | | | | | | The dynamic add path for PCI Host Bridges can fail to configure children adapters under P5IOC controllers. It fails to properly fixup bus/device resources, and it fails to properly enable EEH. Both of these steps need to occur before any children devices are enabled in pci_bus_add_devices(). Signed-off-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] powerpc: Save device BARs much earlier in the boot sequenceLinas Vepstas2006-01-101-2/+1
| | | | | | | | | | 241-eeh-save-bars-earlier.patch Save the PCI device bars *before* any PCI probing is done. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org> (cherry picked from 76c902b919098860f3d4e125f847abcc4cb1782a commit)
* [PATCH] powerpc: Don't continue with PCI Error recovery if slot reset failed.Linas Vepstas2006-01-101-1/+3
| | | | | | | | | | | | 238-eeh-stop-if-reset_failed.patch If the firmware is unable to reset the PCI slot for some reason, then don't attempt any further recovery steps after that point. Instead, mark the device as permanently failed. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org> (cherry picked from e06b942521eb2cdaf232726f45a820d5837acb12 commit)
* [PATCH] powerpc: Remove duplicate codeLinas Vepstas2006-01-101-0/+3
| | | | | | | | | | | 234-eeh-find-pe.patch The find_device_pe() routine is duplicated in two files. Remove one of the two copies, declare the other extern. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org> (cherry picked from 48408e708282d4d0269136ff27ea5acbd9410b5a commit)
* [PATCH] powerpc: Split out PCI address cache to its own fileLinas Vepstas2006-01-101-0/+8
| | | | | | | | | | | | | | | 25-pci-address-cache.patch The core EEH file is rather large. This patch splits out a self-contained chunk of it into its own file. This is the chunk that performes the caching and lookup of pci devices based on the i/o addresses of thier resoures. This code is almos architecture-independent and could be used by any system that wanted to find a pci device based only on the i/o address used by the device. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org> (cherry picked from b0b291d59906d4a9a89ed9e34d9fd684c7188924 commit)
* [PATCH] powerpc: PCI Error Recovery: PPC64 core recovery routinesLinas Vepstas2006-01-101-0/+9
| | | | | | | | | | Various PCI bus errors can be signaled by newer PCI controllers. The core error recovery routines are architecture dependent. This patch adds a recovery infrastructure for the PPC64 pSeries systems. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org> (cherry picked from e8ca11b460c4c9c7fa6b529be221529ebd770e38 commit)
* [PATCH] powerpc: sanitize header files for user space includesArnd Bergmann2006-01-091-0/+2
| | | | | | | | | | | | | | | include/asm-ppc/ had #ifdef __KERNEL__ in all header files that are not meant for use by user space, include/asm-powerpc does not have this yet. This patch gets us a lot closer there. There are a few cases where I was not sure, so I left them out. I have verified that no CONFIG_* symbols are used outside of __KERNEL__ any more and that there are no obvious compile errors when including any of the headers in user space libraries. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
* powerpc: Merge pci.hPaul Mackerras2005-11-191-2/+0
| | | | | | | | | | This involves some minor changes: a few unused functions that the ppc32 pci.c provides are no longer declared here or exported; pcibios_assign_all_busses now just refers to the pci_assign_all_buses variable on both 32-bit and 64-bit; pcibios_scan_all_fns is now just 0 instead of a function that always returns 0 on 64-bit. Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] powerpc: pci_64 fixes & cleanupsBenjamin Herrenschmidt2005-11-161-1/+0
| | | | | | | | | | | | | | | | I discovered that in some cases (PowerMac for example) we wouldn't properly map the PCI IO space on recent kernels. In addition, the code for initializing PCI host bridges was scattered all over the place with some duplication between platforms. This patch fixes the problem and does a small cleanup by creating a pcibios_alloc_controller() in pci_64.c that is similar to the one in pci_32.c (just takes an additional device node argument) that takes care of all the grunt allocation and initialisation work. It should work for both boot time and dynamically allocated PHBs. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] ppc64: mark failed devicesLinas Vepstas2005-11-101-0/+7
| | | | | | | | | | | | 17-eeh-slot-marking-bug.patch A device that experiences a PCI outage may be just one deivce out of many that was affected. In order to avoid repeated reports of a failure, the entire tree of affected devices should be marked as failed. This patch marks up the entire tree. Signed-off-by: Linas Vepstas <linas@linas.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] ppc64: Save & restore of PCI device BARSLinas Vepstas2005-11-101-0/+23
| | | | | | | | | | | | | | | | | 14-eeh-device-bar-save.patch After a PCI device has been resest, the device BAR's and other config space info must be restored to the same state as they were in when the firmware first handed us this device. This will allow the PCI device driver, when restarted, to correctly recognize and set up the device. Tis patch saves the device config space as early as reasonable after the firmware has handed over the device. Te state resore funcion is inteded for use by the EEH recovery routines. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] ppc64: PCI reset support routinesLinas Vepstas2005-11-101-0/+14
| | | | | | | | | | | | | | 13-eeh-recovery-support-routines.patch EEH Recovery support routines This patch adds routines required to help drive the recovery of EEH-frozen slots. The main function is to drive the PCI #RST signal line high for a qurter of a second, and then allow for a second & a half of settle time. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] ppc64: PCI address cache minor fixesLinas Vepstas2005-11-101-4/+0
| | | | | | | | | | | | | | | 03-eeh-addr-cache-cleanup.patch This is a minor patch to clean up a buglet related to the PCI address cache. (The buglet doesn't manifes itself unless there are also bugs elsewhere, which is why its minor.). Also: -- Improved debug printing. -- Declare some private routines as static -- Adds reference counting to struct pci_dn->pcidev structure Signed-off-by: Linas Vepstas <linas@linas.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] ppc64: uniform usage of bus unit id interfaceslinas2005-11-101-0/+4
| | | | | | | | | | | | | 01-pci-dn-uniformization.patch This patch changes the rtas_pci interface to use the new struct pci_dn structure for two routines that work with pci device nodes. This patch also does some minor janitorial work: it uses some handy macros and cleans up some trailing whitespace in the affected file. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] dlpar enable for OF pci probeJohn Rose2005-11-071-0/+1
| | | | | | | | | This patch contains the arch/ppc64 bits for enabling DLPAR and PCI Hotplug for the new OF-based PCI probe mechanism. This code path is currently broken. Signed-off-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* powerpc: Move iSeries_pci.c to powerpc/platform/iseriesStephen Rothwell2005-09-281-0/+54
and rename it to pci.c. This also required moving arch/ppc64/kernel/pci.h into include/asm-powerpc (called ppc-pci.h. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
OpenPOWER on IntegriCloud