| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Documentation:
- MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
Loongson1C:
- Add CPU support for Loongson1C
- Add board support
- Add defconfig
- Add RTC support for Loongson1C board
All this except one Documentation fix has sat in linux-next and has
survived Imagination's automated build test system"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
MIPS: ptrace: Fix regs_return_value for kernel context
MIPS: VDSO: Drop duplicated -I*/-E* aflags
MIPS: Fix -mabi=64 build of vdso.lds
MIPS: Enable hardened usercopy
MIPS: generic: Convert SEAD-3 to a generic board
MIPS: generic: Introduce generic DT-based board support
MIPS: Support generating Flattened Image Trees (.itb)
MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
MIPS: Print CM error reports upon bus errors
MIPS: Support per-device DMA coherence
MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
MIPS: Sanitise coherentio semantics
MIPS: PCI: Support generic drivers
MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
MIPS: PCI: Inline pcibios_assign_all_busses
MIPS: PCI: Make pcibios_set_cache_line_size an initcall
MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
MIPS: PCI: Use struct list_head lists
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The SEAD-3 board is now probing its EHCI controller using the generic
EHCI driver & its generic-ehci device tree binding. Remove the unused
SEAD-3 specific EHCI code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14052/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
This driver should initialize controller only, PHY initialization should
be handled by separated PHY driver. We already have phy-bcm-ns-usb2 in
place so let it makes its duty.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
With LPAE config we don't have omap3 or omap4 selected for
omap5 variants.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fixes the following sparse warning:
drivers/usb/host/ohci-at91.c:141:15: warning:
symbol 'at91_dt_syscon_sfr' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Fix to return error code -ENOMEM from the usb_create_shared_hcd()
error handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\ \
| |/
| |
| |
| |
| | |
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)
the ->primary_hcd will be set to NULL at USB3 hcd removal.
Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
ohci-omap doesn't need to include mach/irqs.h - nothing within this
driver needs anything from this header file. Remove this include.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
The mach/hardware.h include doesn't seem to be necessary to build
ohci-sa1111, so let's remove it to kill off an unnecessary platform
specific include.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The neponset is a daughter board for the Assabet platform, which has a
SA1111 chip on it. If we're initialising the SA1111 OHCI, and we're
part of a neponset, the host platform must be an Assabet.
This allows us to eliminate machine_has_neponset() from this driver,
replacing it instead with machine_is_assabet(), and killing the
mach/assabet.h include.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The usb controller does not manage correctly the suspend mode for
the ehci. In echi mode, there is no way to suspend without any
device connected to it. This is why this specific control is added
to fix this issue. Since the suspend mode works in ohci mode, this
specific control works by suspend the usb controller in ohci mode.
This specific control is by setting the SUSPEND_A/B/C fields of
SFR_OHCIICR(OHCI Interrupt Configuration Register) in the SFR
while the OHCI USB suspend.
This set operation must be done before the USB clock disabled,
clear operation after the USB clock enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| | |
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| | |
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| | |
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| | |
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| | |
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\ \
| |/
| |
| |
| |
| | |
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Enqueue the first TRB even if full_len is zero.
Without this "adb install <apk>" freezes the system.
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Fixes: 86065c2719a5 ("xhci: don't rely on precalculated value of needed trbs in the enqueue loop")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
GPIO control register is divided into IOPINS1 and IOPINS2.
And low 4-bit of register is controls output.
So, this patch fixes wrong mask of GPIO output.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In ehci_turn_off_all_ports() all EHCI port registers are cleared to zero.
On some hardware, this can lead to an system hang,
when ehci_port_power() accesses the already cleared registers.
This patch changes the order of cleanup.
First call ehci_port_power() which respects the current bits in
port status registers
and afterwards cleanup the hard way by setting everything to zero.
Signed-off-by: Marc Ohlf <ohlf@mkt-sys.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Allwinner A64 EHCI requires 4 clocks to be enabled.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently bcma-hcd driver handles 3 different bcma cores:
1) BCMA_CORE_USB20_HOST (0x819)
2) BCMA_CORE_NS_USB20 (0x504)
3) BCMA_CORE_NS_USB30 (0x505)
The first one was introduced years ago and so far was used on MIPS
devices only. All Northstar (ARM) devices were using other two cores
which allowed easy implementation of separated initialization paths.
It seems however Broadcom decided to reuse this old USB 2.0 controller
on some recently introduced cheaper Northstar BCM53573 SoCs. I noticed
this on Tenda AC9 (based on BCM47189B0 belonging to BCM53573 family).
There is no difference in this old controller core identification
between MIPS and ARM devices: they share the same id and revision. We
need different controller initialization procedure however.
To handle this add a check for architecture and implement required
initialization for ARM case.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
The workqueue "workqueue" has multiple workitems which may require
ordering. Hence, a dedicated ordered workqueue has been used.
Since the workqueue is not being used on a memory reclaim path,
WQ_MEM_RECLAIM has not been set.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
It's a rather simple controller, we just need to make sure USB is
powered (using GPIO pin) and reset bus core. Once this is done it's
safe to register XHCI controller and let it init PHY and do its magic.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,x;
@@
- if (of_get_property(e1,e2,NULL))
- x = true;
- else
- x = false;
+ x = of_property_read_bool(e1,e2);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Highlights:
- ARM64 support for ACPI host bridges
- new drivers for Axis ARTPEC-6 and Marvell Aardvark
- new pci_alloc_irq_vectors() interface for MSI-X, MSI, legacy INTx
- pci_resource_to_user() cleanup (more to come)
Detailed summary:
Enumeration:
- Move ecam.h to linux/include/pci-ecam.h (Jayachandran C)
- Add parent device field to ECAM struct pci_config_window (Jayachandran C)
- Add generic MCFG table handling (Tomasz Nowicki)
- Refactor pci_bus_assign_domain_nr() for CONFIG_PCI_DOMAINS_GENERIC (Tomasz Nowicki)
- Factor DT-specific pci_bus_find_domain_nr() code out (Tomasz Nowicki)
Resource management:
- Add devm_request_pci_bus_resources() (Bjorn Helgaas)
- Unify pci_resource_to_user() declarations (Bjorn Helgaas)
- Implement pci_resource_to_user() with pcibios_resource_to_bus() (microblaze, powerpc, sparc) (Bjorn Helgaas)
- Request host bridge window resources (designware, iproc, rcar, xgene, xilinx, xilinx-nwl) (Bjorn Helgaas)
- Make PCI I/O space optional on ARM32 (Bjorn Helgaas)
- Ignore write combining when mapping I/O port space (Bjorn Helgaas)
- Claim bus resources on MIPS PCI_PROBE_ONLY set-ups (Bjorn Helgaas)
- Remove unicore32 pci=firmware command line parameter handling (Bjorn Helgaas)
- Support I/O resources when parsing host bridge resources (Jayachandran C)
- Add helpers to request/release memory and I/O regions (Johannes Thumshirn)
- Use pci_(request|release)_mem_regions (NVMe, lpfc, GenWQE, ethernet/intel, alx) (Johannes Thumshirn)
- Extend pci=resource_alignment to specify device/vendor IDs (Koehrer Mathias (ETAS/ESW5))
- Add generic pci_bus_claim_resources() (Lorenzo Pieralisi)
- Claim bus resources on ARM32 PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
- Remove ARM32 and ARM64 arch-specific pcibios_enable_device() (Lorenzo Pieralisi)
- Add pci_unmap_iospace() to unmap I/O resources (Sinan Kaya)
- Remove powerpc __pci_mmap_set_pgprot() (Yinghai Lu)
PCI device hotplug:
- Allow additional bus numbers for hotplug bridges (Keith Busch)
- Ignore interrupts during D3cold (Lukas Wunner)
Power management:
- Enforce type casting for pci_power_t (Andy Shevchenko)
- Don't clear d3cold_allowed for PCIe ports (Mika Westerberg)
- Put PCIe ports into D3 during suspend (Mika Westerberg)
- Power on bridges before scanning new devices (Mika Westerberg)
- Runtime resume bridge before rescan (Mika Westerberg)
- Add runtime PM support for PCIe ports (Mika Westerberg)
- Remove redundant check of pcie_set_clkpm (Shawn Lin)
Virtualization:
- Add function 1 DMA alias quirk for Marvell 88SE9182 (Aaron Sierra)
- Add DMA alias quirk for Adaptec 3805 (Alex Williamson)
- Mark Atheros AR9485 and QCA9882 to avoid bus reset (Chris Blake)
- Add ACS quirk for Solarflare SFC9220 (Edward Cree)
MSI:
- Fix PCI_MSI dependencies (Arnd Bergmann)
- Add pci_msix_desc_addr() helper (Christoph Hellwig)
- Switch msix_program_entries() to use pci_msix_desc_addr() (Christoph Hellwig)
- Make the "entries" argument to pci_enable_msix() optional (Christoph Hellwig)
- Provide sensible IRQ vector alloc/free routines (Christoph Hellwig)
- Spread interrupt vectors in pci_alloc_irq_vectors() (Christoph Hellwig)
Error Handling:
- Bind DPC to Root Ports as well as Downstream Ports (Keith Busch)
- Remove DPC tristate module option (Keith Busch)
- Convert Downstream Port Containment driver to use devm_* functions (Mika Westerberg)
Generic host bridge driver:
- Select IRQ_DOMAIN (Arnd Bergmann)
- Claim bus resources on PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
ACPI host bridge driver:
- Add ARM64 acpi_pci_bus_find_domain_nr() (Tomasz Nowicki)
- Add ARM64 ACPI support for legacy IRQs parsing and consolidation with DT code (Tomasz Nowicki)
- Implement ARM64 AML accessors for PCI_Config region (Tomasz Nowicki)
- Support ARM64 ACPI-based PCI host controller (Tomasz Nowicki)
Altera host bridge driver:
- Check link status before retrain link (Ley Foon Tan)
- Poll for link up status after retraining the link (Ley Foon Tan)
Axis ARTPEC-6 host bridge driver:
- Add PCI_MSI_IRQ_DOMAIN dependency (Arnd Bergmann)
- Add DT binding for Axis ARTPEC-6 PCIe controller (Niklas Cassel)
- Add Axis ARTPEC-6 PCIe controller driver (Niklas Cassel)
Intel VMD host bridge driver:
- Use lock save/restore in interrupt enable path (Jon Derrick)
- Select device dma ops to override (Keith Busch)
- Initialize list item in IRQ disable (Keith Busch)
- Use x86_vector_domain as parent domain (Keith Busch)
- Separate MSI and MSI-X vector sharing (Keith Busch)
Marvell Aardvark host bridge driver:
- Add DT binding for the Aardvark PCIe controller (Thomas Petazzoni)
- Add Aardvark PCI host controller driver (Thomas Petazzoni)
- Add Aardvark PCIe support for Armada 3700 (Thomas Petazzoni)
Microsoft Hyper-V host bridge driver:
- Fix interrupt cleanup path (Cathy Avery)
- Don't leak buffer in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
- Handle all pending messages in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
NVIDIA Tegra host bridge driver:
- Program PADS_REFCLK_CFG* always, not just on legacy SoCs (Stephen Warren)
- Program PADS_REFCLK_CFG* registers with per-SoC values (Stephen Warren)
- Use lower-case hex consistently for register definitions (Thierry Reding)
- Use generic pci_remap_iospace() rather than ARM32-specific one (Thierry Reding)
- Stop setting pcibios_min_mem (Thierry Reding)
Renesas R-Car host bridge driver:
- Drop gen2 dummy I/O port region (Bjorn Helgaas)
TI DRA7xx host bridge driver:
- Fix return value in case of error (Christophe JAILLET)
Xilinx AXI host bridge driver:
- Fix return value in case of error (Christophe JAILLET)
Miscellaneous:
- Make bus_attr_resource_alignment static (Ben Dooks)
- Include <asm/dma.h> for isa_dma_bridge_buggy (Ben Dooks)
- MAINTAINERS: Add file patterns for PCI device tree bindings (Geert Uytterhoeven)
- Make host bridge drivers explicitly non-modular (Paul Gortmaker)"
* tag 'pci-v4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (125 commits)
PCI: xgene: Make explicitly non-modular
PCI: thunder-pem: Make explicitly non-modular
PCI: thunder-ecam: Make explicitly non-modular
PCI: tegra: Make explicitly non-modular
PCI: rcar-gen2: Make explicitly non-modular
PCI: rcar: Make explicitly non-modular
PCI: mvebu: Make explicitly non-modular
PCI: layerscape: Make explicitly non-modular
PCI: keystone: Make explicitly non-modular
PCI: hisi: Make explicitly non-modular
PCI: generic: Make explicitly non-modular
PCI: designware-plat: Make it explicitly non-modular
PCI: artpec6: Make explicitly non-modular
PCI: armada8k: Make explicitly non-modular
PCI: artpec: Add PCI_MSI_IRQ_DOMAIN dependency
PCI: Add ACS quirk for Solarflare SFC9220
arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700
PCI: aardvark: Add Aardvark PCI host controller driver
dt-bindings: add DT binding for the Aardvark PCIe controller
PCI: tegra: Program PADS_REFCLK_CFG* registers with per-SoC values
...
|
| | |\
| | |
| | |
| | |
| | | |
Conflicts:
drivers/nvme/host/pci.c
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Currently the Linux PCI core does not touch power state of PCI bridges and
PCIe ports when system suspend is entered. Leaving them in D0 consumes
power unnecessarily and may prevent the CPU from entering deeper C-states.
With recent PCIe hardware we can power down the ports to save power given
that we take into account few restrictions:
- The PCIe port hardware is recent enough, starting from 2015.
- Devices connected to PCIe ports are effectively in D3cold once the port
is transitioned to D3 (the config space is not accessible anymore and
the link may be powered down).
- Devices behind the PCIe port need to be allowed to transition to D3cold
and back. There is a way both drivers and userspace can forbid this.
- If the device behind the PCIe port is capable of waking the system it
needs to be able to do so from D3cold.
This patch adds a new flag to struct pci_device called 'bridge_d3'. This
flag is set and cleared by the PCI core whenever there is a change in power
management state of any of the devices behind the PCIe port. When system
later on is suspended we only need to check this flag and if it is true
transition the port to D3 otherwise we leave it in D0.
Also provide override mechanism via command line parameter
"pcie_port_pm=[off|force]" that can be used to disable or enable the
feature regardless of the BIOS manufacturing date.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
We now have implicit batching in the timer wheel. The slack API is no longer
used, so remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094342.189813118@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| |\ \ \
| |/ /
| | |
| | |
| | |
| | | |
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Contained are some standard fixes and unusually an extension to the
Reset API. Some of those changes are required to fix a bug introduced
in -rc1, which introduces extra 'reset line checks' i.e. whether the
line is shared or not. If a line is shared and the new *_shared() API
is not used, the request fails with an error. This breaks USB in v4.7
for ST's platforms.
Admittedly, there are some patches contained in our (MFD/Reset)
immutable branch which are not true -fixes, but there isn't anything I
can do about that. Rest assured though, there aren't any API
'changes'. Everything is the same from the consumer's perspective.
- Use new reset_*_get_shared() variant to prevent reset line
obtainment failure (Fixes commit 0b52297f2288: "reset: Add support
for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning"
* tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
reset: TRIVIAL: Add line break at same place for similar APIs
reset: Supply *_shared variant calls when using *_optional APIs
reset: Supply *_shared variant calls when using of_* API
reset: Ensure drivers are explicit when requesting reset lines
reset: Reorder inline reset_control_get*() wrappers
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
On the STiH410 B2120 development board the ST EHCI IP shares its reset
line with the OHCI IP. New functionality in the reset subsystems forces
consumers to be explicit when requesting shared/exclusive reset lines.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| | | |/
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
On the STiH410 B2120 development board the ST EHCI IP shares its reset
line with the OHCI IP. New functionality in the reset subsystems forces
consumers to be explicit when requesting shared/exclusive reset lines.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
gcc warns about what first looks like a reference to an uninitialized
variable:
drivers/usb/host/xhci-ring.c: In function 'handle_cmd_completion':
drivers/usb/host/xhci-ring.c:753:4: error: 'ep_ring' may be used uninitialized in this function [-Werror=maybe-uninitialized]
xhci_unmap_td_bounce_buffer(xhci, ep_ring, cur_td);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/xhci-ring.c:647:20: note: 'ep_ring' was declared here
struct xhci_ring *ep_ring;
^~~~~~~
It's clear to see that the list_empty() check means it can never be
uninitialized, however it still looks wrong:
When ep->cancelled_td_list contains more than one entry, the
ep_ring variable will point to the ring that was retrieved
from the last urb, and we have to look it up again in the
second loop instead, which fixes the behavior and gets rid of the
warning too.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f9c589e142d0 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.8 merge window
Here's the big pull request for Peripheral stack and
all related drivers.
This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).
There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.
For the Gadget API, we're just adding tracepoints to
aid debugging activities.
Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
|
| | |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
instead of defining all functions as static inlines,
let's move them to udc-core and export them with
EXPORT_SYMBOL_GPL, that way we can make sure that
only GPL drivers will use them.
As a side effect, it'll be nicer to add tracepoints
to the gadget API.
While at that, also fix Kconfig dependencies to
avoid randconfig build failures.
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
No more users for it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Requesting the only property that the driver needs using the
unified device property interface so it will be available
for all types of platforms, not just the ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
It's only used with rings that have link trbs
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Only used in one place, replace with trb_is_link() helper
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
inc_deq() is called both for rings with link trbs and the event ring
without link trbs.
The last_trb() check in inc_deq() has a off by one error, going beyond
allocated array when checking if trb == [TRBS_PER_SEGMENT], and the whole
inc_deq() depend on this.
Rewrite the inc_deq() funciton, remove the faulty last_trb() helper, add
new last_trb_on_seg() and last_trb_on_ring() helpers
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add a new is_link_trb() function that only checks for link trbs.
We want to split generic last_trb() function which is used for both
event rings without link trbs, and endpoint and command rings with links.
This will allow us to easier check for link trbs added mid segments.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Remove the event ring related checks in inc_enq()
Host hardware is the producer of events on the event ring,
driver will not queue anything, or call inc_enq() for the
event ring.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
If the last trb before a link is not packet size aligned, and is not
splittable then use a bounce buffer for that chunk of max packet size
unalignable data.
Allocate a max packet size bounce buffer for every segment of a bulk
endpoint ring at the same time as allocating the ring.
If we need to align the data before the link trb in that segment then
copy the data to the segment bounce buffer, dma map it, and enqueue it.
Once the td finishes, or is cancelled, unmap it.
For in transfers we need to first map the bounce buffer, then queue it,
after it finishes, copy the bounce buffer to the original sg list, and
finally unmap it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
