| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| ... | |
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
After the lock is dropped, it is possible that the cpufreq_dev gets
freed before we call get_level() and that can cause kernel to crash.
Drop the lock after we are done using the structure.
Cc: 4.2+ <stable@vger.kernel.org> # 4.2+
Fixes: 02373d7c69b4 ("thermal: cpu_cooling: fix lockdep problems in cpu_cooling")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
For INT3403 sensor PTYP field is mandatory. But some platforms didn't
have this field for sensors. This cause load failure for int3403 driver.
This change checks for the presence of _TMP method and if present, then
treats this device as a sensor.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
| | | |/ /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch fix the few typos in function header of
acpi_parse_trt. Also, fix the typo in kernel debug
message for acpi_parse_art.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
| | |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Some parameters are not documented, or not present at all, in thermal
governors code.
Signed-off-by: Willy Wolff <willy.mh.wolff@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Intel Cherry Trail Whiskey Cove PMIC
- TI LP87565 PMIC
New Device Support:
- Add support for Cannonlake to intel-lpss-pci
- Add support for Simatic IOT2000 to intel_quark_i2c_gpio
New Functionality:
- Add Regulator support (axp20x)
Fix-ups:
- Rework IRQ handling (intel_soc_pmic_bxtwc, rtsx_pcr, cros_ec)
- Remove unused/unwelcome code (ipaq-micro, wm831x-core, da9062-core)
- Provide deregistration on unbind (rn5t618)
- Rework DT code/documentation (arizona)
- Constify things (fsl-imx25-tsadc)
- MAINTAINERS updates (DA9062/61)
- Kconfig configuration adaptions (INTEL_SOC_PMIC, MFD_AXP20X_I2C)
- Switch to DMI matching (intel_quark_i2c_gpio)
- Provide an appropriate level of error checking (wm831x-{i2c,spi},
twl4030-irq, tc6393xb)
- Make use of devm_* (resource handling) calls (intel_soc_pmic_bxtwc,
stm32-timers, atmel-flexcom, cros_ec, fsl-imx25-tsadc,
exynos-lpass, palmas, qcom-spmi-pmic, smsc-ece1099,
motorola-cpcap)"
[ Skipped the last commit in that series that added eight thousand
lines of pointless repeated register definitions. - Linus ]
* tag 'mfd-next-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (38 commits)
mfd: Add LP87565 PMIC support
mfd: cros_ec: Free IRQ on exit
dt-bindings: vendor-prefixes: Add arctic to vendor prefix
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: axp20x-i2c: Document that this must be builtin on x86
mfd: Add Cherry Trail Whiskey Cove PMIC driver
mfd: tc6393xb: Handle return value of clk_prepare_enable
mfd: intel_quark_i2c_gpio: Add support for SIMATIC IOT2000 platform
mfd: intel_quark_i2c_gpio: Use dmi_system_id table for retrieving frequency
mfd: motorola-cpcap: Use devm_of_platform_populate()
mfd: smsc-ece: Use devm_of_platform_populate()
mfd: qcom-spmi-pmic: Use devm_of_platform_populate()
mfd: palmas: Use devm_of_platform_populate()
mfd: exynos: Use devm_of_platform_populate()
mfd: fsl-imx25: Use devm_of_platform_populate()
mfd: cros_ec: Use devm_of_platform_populate()
mfd: atmel: Use devm_of_platform_populate()
mfd: stm32-timers: Use devm_of_platform_populate()
mfd: intel_soc_pmic: Select designware i2c-bus driver
...
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Since all second level thermal IRQs are consumed by the same
device(bxt_wcove_thermal), there is no need to expose them as separate
interrupts. We can just export only the first level IRQs for thermal and
let the device(bxt_wcove_thermal) driver handle the second level IRQs
based on thermal interrupt status register. Also, just using only the
first level IRQ will eliminate the bug involved in requesting only the
second level IRQ and not explicitly enable the first level IRQ. For
more info on this issue please read the details at,
https://lkml.org/lkml/2017/2/27/148
This patch also makes relevant change in bxt_wcove_thermal driver to use
only first level PMIC thermal IRQ.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big patchset of USB and PHY driver updates for 4.13-rc1.
On the PHY side, they decided to move files around to "make things
easier" in their tree. Hopefully that wasn't a mistake, but in
linux-next testing, we haven't had any reported problems.
There's the usual set of gadget and xhci and musb updates in here as
well, along with a number of smaller updates for a raft of different
USB drivers. Full details in the shortlog, nothing really major.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (173 commits)
Add USB quirk for HVR-950q to avoid intermittent device resets
USB hub_probe: rework ugly goto-into-compound-statement
usb: host: ohci-pxa27x: Handle return value of clk_prepare_enable
USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
usbip: Fix uninitialized variable bug in vhci
usb: core: read USB ports from DT in the usbport LED trigger driver
dt-bindings: leds: document new trigger-sources property
usb: typec: ucsi: Add ACPI driver
usb: typec: Add support for UCSI interface
usb: musb: compress return logic into one line
USB: serial: propagate late probe errors
USB: serial: refactor port endpoint setup
usb: musb: tusb6010_omap: Convert to DMAengine API
ARM: OMAP2+: DMA: Add slave map entries for 24xx external request lines
usb: musb: tusb6010: Handle DMA TX completion in DMA callback as well
usb: musb: tusb6010_omap: Allocate DMA channels upfront
usb: musb: tusb6010_omap: Create new struct for DMA data/parameters
usb: musb: tusb6010_omap: Use one musb_ep_select call in tusb_omap_dma_program
usb: musb: tusb6010: Add MUSB_G_NO_SKB_RESERVE to quirks
usb: musb: Add quirk to avoid skb reserve in gadget mode
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Use the new helper for reusing a device-tree node of another device
instead of managing the node references explicitly.
This also makes sure that the new of_node_reuse flag is set if the
device is ever reprobed, something which specifically now avoids driver
core from attempting to claim any pinmux resources already claimed by
the parent device.
Fixes: ec4664b3fd6d ("thermal: max77620: Add thermal driver for reporting junction temp")
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The thermal child device reuses the parent MFD-device device-tree node
when registering a thermal zone, but did not take a reference to the
node.
This leads to a reference imbalance, and potential use-after-free, when
the node reference is dropped by the platform-bus device destructor
(once for the child and later again for the parent).
Fix this by dropping any reference already held to a device-tree node
and getting a reference to the parent's node which will be balanced on
reprobe or on platform-device release, whichever comes first.
Note that simply clearing the of_node pointer on probe errors and on
driver unbind would not allow the use of device-managed resources as
specifically thermal_zone_of_sensor_unregister() claims that a valid
device-tree node pointer is needed during deregistration (even if it
currently does not seem to use it).
Fixes: ec4664b3fd6d ("thermal: max77620: Add thermal driver for reporting junction temp")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fix the compile after the switch to the UUID API in commit f4c19ac9
("thermal: int340x_thermal: Switch to use new generic UUID API").
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
| |/ /
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
There are new types and helpers that are supposed to be used in
new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
The conversion fixes a potential bug in int340x_thermal as well
since we have to use memcmp() on binary data.
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Tweak the Kconfig description to mention support for NSP and make the
default on for iProc based platforms.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
Add a missing character in this description for a function.
Acked-by: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
ti_bandgap_build()
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus remove such statements here.
Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf
Acked-by: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kcalloc".
This issue was detected by using the Coccinelle software.
Acked-by: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Making thermal_emergency_poweroff static fixes sparse warning:
drivers/thermal/thermal_core.c:6: warning: symbol
'thermal_emergency_poweroff' was not declared. Should it be static?
Fixes: ef1d87e06ab4 ("thermal: core: Add a back up thermal shutdown mechanism")
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| |/
|
|
|
|
|
|
|
|
| |
Building this driver with W=1 reports:
warning: variable 'trip' set but not used [-Wunused-but-set-variable]
The call for of_thermal_get_trip_points() is useless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- Fix a problem where orderly_shutdown() is called for multiple times
due to multiple critical overheating events raised in a short period
by platform thermal driver. (Keerthy)
- Introduce a backup thermal shutdown mechanism, which invokes
kernel_power_off()/emergency_restart() directly, after
orderly_shutdown() being issued for certain amount of time(specified
via Kconfig). This is useful in certain conditions that userspace may
be unable to power off the system in a clean manner and leaves the
system in a critical state, like in the middle of driver probing
phase. (Keerthy)
- Introduce a new interface in thermal devfreq_cooling code so that the
driver can provide more precise data regarding actual power to the
thermal governor every time the power budget is calculated. (Lukasz
Luba)
- Introduce BCM 2835 soc thermal driver and northstar thermal driver,
within a new sub-folder. (Rafał Miłecki)
- Introduce DA9062/61 thermal driver. (Steve Twiss)
- Remove non-DT booting on TI-SoC driver. Also add support to fetching
coefficients from DT. (Keerthy)
- Refactorf RCAR Gen3 thermal driver. (Niklas Söderlund)
- Small fix on MTK and intel-soc-dts thermal driver. (Dawei Chien,
Brian Bian)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
thermal: core: Add a back up thermal shutdown mechanism
thermal: core: Allow orderly_poweroff to be called only once
Thermal: Intel SoC DTS: Change interrupt request behavior
trace: thermal: add another parameter 'power' to the tracing function
thermal: devfreq_cooling: add new interface for direct power read
thermal: devfreq_cooling: refactor code and add get_voltage function
thermal: mt8173: minor mtk_thermal.c cleanups
thermal: bcm2835: move to the broadcom subdirectory
thermal: broadcom: ns: specify myself as MODULE_AUTHOR
thermal: da9062/61: Thermal junction temperature monitoring driver
Documentation: devicetree: thermal: da9062/61 TJUNC temperature binding
thermal: broadcom: add Northstar thermal driver
dt-bindings: thermal: add support for Broadcom's Northstar thermal
thermal: bcm2835: add thermal driver for bcm2835 SoC
dt-bindings: Add thermal zone to bcm2835-thermal example
thermal: rcar_gen3_thermal: add suspend and resume support
thermal: rcar_gen3_thermal: store device match data in private structure
thermal: rcar_gen3_thermal: enable hardware interrupts for trip points
thermal: rcar_gen3_thermal: record and check number of TSCs found
thermal: rcar_gen3_thermal: check that TSC exists before memory allocation
...
|
| | |\ |
|
| | | |\
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal into thermal-soc
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If thermal bank with 4 sensors, thermal driver should read TEMP_MSR3.
However, currently thermal driver would not read TEMP_MSR3 since mt8173
thermal driver only use 3 sensors on each thermal bank at the same time,
so this patch would not effect temperature.
Only if mt mt8173 thermal driver use 4 sensors on any thermal bank, would
read third sensor two times, and lose fourth sensor of vale.
cc: stable@vger.kernel.org
Fixes: b7cf0053738c ("thermal: Add Mediatek thermal driver for mt2701.")
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We already have 2 Broadcom drivers and at least 1 more is coming. This
made us create broadcom subdirectory where bcm2835 should be moves now.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Just in case someone uses modinfo to find (blame) me.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add junction temperature monitoring supervisor device driver, compatible
with the DA9062 and DA9061 PMICs. A MODULE_DEVICE_TABLE() macro is added.
If the PMIC's internal junction temperature rises above T_WARN (125 degC)
an interrupt is issued. This T_WARN level is defined as the
THERMAL_TRIP_HOT trip-wire inside the device driver.
The thermal triggering mechanism is interrupt based and happens when the
temperature rises above a given threshold level. The component cannot
return an exact temperature, it only has knowledge if the temperature is
above or below a given threshold value. A status bit must be polled to
detect when the temperature falls below that threshold level again. A
kernel work queue is configured to repeatedly poll and detect when the
temperature falls below this trip-wire, between 1 and 10 second intervals
(defaulting at 3 seconds).
This scheme is provided as an example. It would be expected that any
final implementation will also include a notify() function and any of these
settings could be altered to match the application where appropriate.
When over-temperature is reached, the interrupt from the DA9061/2 will be
repeatedly triggered. The IRQ is therefore disabled when the first
over-temperature event happens and the status bit is polled using a
work-queue until it becomes false.
This strategy is designed to allow the periodic transmission of uevents
(HOT trip point) as the first level of temperature supervision method. It
is intended for non-invasive temperature control, where the necessary
measures for cooling the system down are left to the host software. Once
the temperature falls again, the IRQ is re-enabled so a new critical
over-temperature event can be detected.
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Northstar is a SoC family commonly used in home routers. This commit
adds a driver for checking CPU temperature. As Northstar Plus seems to
also have this IP block this new symbol gets ARCH_BCM_IPROC dependency.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add basic thermal driver for bcm2835 SoC.
This driver currently make sure that tsense HW block is set up
correctly.
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
To restore operation it's easiest to reinitialise all TSCs. In order to
do this the current trip window needs to be stored in the TSC structure
so that it can be restored upon resume.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The device match data needs to be accessible outside the probe function,
store it in the private data structure.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Enable hardware trip points by implementing the set_trips callback. The
thermal core will take care of setting the initial trip point window and
to update it once the driver reports a TSC has moved outside it.
The interrupt structure for this device is a bit odd. There is not a
dedicated IRQ for each TSC, instead the interrupts are shared between
all TSCs. IRQn is fired if the temp monitored in IRQTEMPn is reached in
any of the TSCs, example IRQ3 is fired if temperature in IRQTEMP3 is
reached in either TSC0, TSC1 or TSC2.
For this reason the usage of interrupts in this driver is an all-on or
all-off design. When an interrupt happens all TSCs are checked and all
thermal zones are updated. This could be refined to be more fine grained
but the thermal core takes care of only updating the thermal zones that
have left their trip point window.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Record how many TSCs are found in struct rcar_gen3_thermal_priv, this is
needed to be able to add hardware interrupts for trip points later. Also
add a check to make sure at least one TSC is found.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Move the check for a TSC resource before allocating memory for a new
TSC. If no TSC is found there is little point in allocating memory for
it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
There is no point in protecting a register read with a lock. This is
most likely a leftover from when the driver was reworked before being
submitted for upstream.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The .thermal_init needs to be delayed a short amount of time to allow
for the TEMP register to contain something useful. If it's not delayed
these warnings are common during boot:
thermal thermal_zone0: failed to read out thermal zone (-5)
thermal thermal_zone1: failed to read out thermal zone (-5)
thermal thermal_zone2: failed to read out thermal zone (-5)
The warnings are triggered by the first call to .get_temp() while the
TEMP register contains 0 and rcar_gen3_thermal_get_temp() returns -EIO
since a TEMP value of 0 will result in a temperature reading which is
out of specifications.
This should have been done in the initial commit which adds the driver
as the same issue was found and corrected for r8a7795.
Fixes: 564e73d283af9d4c ("thermal: rcar_gen3_thermal: Add R-Car Gen3 thermal driver")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
ti_thermal_expose_sensor always takes the
devm_thermal_zone_of_sensor_register call for registration
with the device tree nodes present for all the bandgap sensors
for omap3/4/5 and dra7 family. There are large chunks of unused
code. Removing all of them.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Now that slope and offset data are being passed from
device tree no need to populate in driver data.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Currently slope and offset values for calculating the hot spot
temperature of a thermal zone is being taken directly from driver
data. So fetch them from device tree.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
| | |\ \ \ |
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
orderly_poweroff is triggered when a graceful shutdown
of system is desired. This may be used in many critical states of the
kernel such as when subsystems detects conditions such as critical
temperature conditions. However, in certain conditions in system
boot up sequences like those in the middle of driver probes being
initiated, userspace will be unable to power off the system in a clean
manner and leaves the system in a critical state. In cases like these,
the /sbin/poweroff will return success (having forked off to attempt
powering off the system. However, the system overall will fail to
completely poweroff (since other modules will be probed) and the system
is still functional with no userspace (since that would have shut itself
off).
However, there is no clean way of detecting such failure of userspace
powering off the system. In such scenarios, it is necessary for a backup
workqueue to be able to force a shutdown of the system when orderly
shutdown is not successful after a configurable time period.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
| | | |/ /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
thermal_zone_device_check --> thermal_zone_device_update -->
handle_thermal_trip --> handle_critical_trips --> orderly_poweroff
The above sequence happens every 250/500 mS based on the configuration.
The orderly_poweroff function is getting called every 250/500 mS.
With a full fledged file system it takes at least 5-10 Seconds to
power off gracefully.
In that period due to the thermal_zone_device_check triggering
periodically the thermal work queues bombard with
orderly_poweroff calls multiple times eventually leading to
failures in gracefully powering off the system.
Make sure that orderly_poweroff is called only once.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
| | |\ \ \ |
|
| | | |/ /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The interrupt request call in Intel SoC DTS driver may fail if
there is no underlying BIOS support. However, the user space
thermal daemon can still use the thermal zones created by the
SoC DTS driver in polling mode, therefore, instead of bailing
out on interrupt request failures, it is better just to log
a warning message and continue the init process.
Signed-off-by: Brian Bian <brian.bian@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch adds another parameter to the trace function:
trace_thermal_power_devfreq_get_power().
In case when we call directly driver's code for the real power,
we do not have static/dynamic_power values. Instead we get total
power in the '*power' value. The 'static_power' and
'dynamic_power' are set to 0.
Therefore, we have to trace that '*power' value in this scenario.
CC: Steven Rostedt <rostedt@goodmis.org>
CC: Ingo Molnar <mingo@redhat.com>
CC: Zhang Rui <rui.zhang@intel.com>
CC: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch introduces a new interface for device drivers connected to
devfreq_cooling in the thermal framework: get_real_power().
Some devices have more sophisticated methods (like power counters)
to approximate the actual power that they use.
In the previous implementation we had a pre-calculated power
table which was then scaled by 'utilization'
('busy_time' and 'total_time' taken from devfreq 'last_status').
With this new interface the driver can provide more precise data
regarding actual power to the thermal governor every time the power
budget is calculated. We then use this value and calculate the real
resource utilization scaling factor.
Reviewed-by: Chris Diamand <chris.diamand@arm.com>
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
|
| | |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Move the code which gets the voltage for a given frequency.
This code will be resused in few places.
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale MXS Low Resolution ADC
- Freescale i.MX23/i.MX28 LRADC touchscreen
- Motorola CPCAP Power Button
- TI LMU (Lighting Management Unit)
- Atmel SMC (Static Memory Controller)
New Device Support:
- Add support for X-Powers AXP803 to axp20x
- Add support for Dialog Semi DA9061 to da9062-core
- Add support for Intel Cougar Mountain to lpc_ich
- Add support for Intel Gemini Lake to lpc_ich
New Functionality:
- Add Device Tree support; wm831x-*, axp20x, ti-lmu, da9062, sun4i-gpadc
- Add IRQ sense support; motorola-cpcap
- Add ACPI support; cros_ec
- Add Reset support; altera-a10sr
- Add ADC support; axp20x
- Add AC Power support; axp20x
- Add Runtime PM support; atmel-ebi, exynos-lpass
- Add Battery Power Supply support; axp20x
- Add Clock support; exynos-lpass, hi655x-pmic
Fix-ups:
- Implicitly specify required headers; motorola-cpcap, intel_soc_pmic_bxtwc
- Add .remove() method; stm32-timers, exynos-lpass
- Remove unused code; intel_soc_pmic_core, intel-lpss-acpi, ipaq-micro, atmel-smc, menelaus
- Rename variables for clarity; axp20x
- Convert pr_warning() to pr_warn(); db8500-prcmu, sta2x11-mfd, twl4030-power
- Improve formatting; arizona-core, axp20x
- Use raw_spinlock_*() variants; asic3, t7l66xb, tc6393xb
- Simplify/refactor code; arizona-core, atmel-ebi
- Improve error checking; intel_soc_pmic_core
Bug Fixes:
- Ensure OMAP3630/3730 boards can successfully reboot; twl4030-power
- Correct max-register value; stm32-timers
- Extend timeout to account for clock stretching; cros_ec_spi
- Use correct IRQ trigger type; motorola-cpcap
- Fix bad use of IRQ sense register; motorola-cpcap
- Logic error "||" should be "&&"; mxs-lradc-ts"
* tag 'mfd-next-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
input: touchscreen: mxs-lradc: || vs && typos
dt-bindings: Add AXP803's regulator info
mfd: axp20x: Support AXP803 variant
dt-bindings: Add device tree binding for X-Powers AXP803 PMIC
dt-bindings: Make AXP20X compatible strings one per line
mfd: intel_soc_pmic_core: Fix unchecked return value
mfd: menelaus: Remove obsolete local_irq_disable() and local_irq_enable()
mfd: omap-usb-tll: Configure ULPIAUTOIDLE
mfd: omap-usb-tll: Fix inverted bit use for USB TLL mode
mfd: palmas: Fixed spelling mistake in error message
mfd: lpc_ich: Add support for Intel Gemini Lake SoC
mfd: hi655x: Add the clock cell to provide WiFi and Bluetooth
mfd: intel_soc_pmic: Fix a mess with compilation units
mfd: exynos-lpass: Add runtime PM support
mfd: exynos-lpass: Add missing remove() function
mfd: exynos-lpass: Add support for clocks
mfd: exynos-lpass: Remove pad retention control
iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs
mfd: cpcap: Fix bad use of IRQ sense register
mfd: cpcap: Use ack_invert interrupts
...
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Crystal Cove and Whiskey Cove are two different PMICs which are
installed on Intel Atom SoC based platforms.
Moreover there are two independent drivers that by some reason were
supposed (*) to get into one kernel module.
Fix the mess by clarifying Kconfig option for Crystal Cove and split
Whiskey Cove out of it.
(*) It looks like the configuration was never tested with
INTEL_SOC_PMIC=n. The line in Makefile is actually wrong.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> (supporter:ACPI)
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| |\ \ \
| |_|/
|/| | |
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The best place to register the CPU cooling device is from the cpufreq
driver as we would know if all the resources are already available or
not. That's what is done for the cpufreq-dt.c driver as well.
The cpu-cooling driver for dbx500 platform was just (un)registering
with the thermal framework and that can be handled easily by the cpufreq
driver as well and in proper sequence as well.
Get rid of the cooling driver and its its users and manage everything
from the cpufreq driver instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
It is possible for dev_pm_opp_find_freq_exact() to return errors. It was
all fine earlier as dev_pm_opp_get_voltage() had a check within it to
check for invalid OPPs, but dev_pm_opp_put() doesn't have any similar
checks and the callers need to make sure OPP is valid before calling
them.
Also update the later dev_warn_ratelimited() to not print the error
message as the OPP is guaranteed to be valid now.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
There isn't much the user can do on seeing these warnings, as the
hardware is actually okay. dev_err suits much better here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
