| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This patch replaces the static bat0 interface with a dynamic/abstracted
approach. It is now possible to create multiple batX interfaces by
assigning hard interfaces to them. Each batX interface acts as an
independent mesh network. A soft interface is removed once no hard
interface references it any longer.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Kernighan algorithm is not able to calculate the number of set bits
in parallel and the compiler cannot replace it with optimized
instructions.
The kernel provides specialised functions for each cpu which can either
use a software implementation or hardware instruction depending on the
target cpu.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
| |
All routing debug messages are saved in a ring buffer that can be
read via the debugfs file "log".
Note that CONFIG_BATMAN_ADV_DEBUG must be activated to have the
debug logs compiled in.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch changes the sequence number range from 8 or 16 bit to 32 bit.
This should avoid problems with the sequence number sliding window algorithm
which we had seen in the past for broadcast floods or malicious packet
injections. We can not assure 100% security with this patch, but it is quite
an improvement over the old 16 bit sequence numbers:
* expected window size can be increased (4096 -> 65536)
* 64k packets in the right order would now be needed to cause a loop,
which seems practically impossible.
Furthermore, a TTL field has been added to the broadcast packet type, just to
make sure.
These changes required to increase the compatibility level once again.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
[sven.eckelmann@gmx.de: Change atomic64_* back to atomic_*, Rework on
top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Functions and variables which are used only inside one object file can
be declared as static. This helped to find unused functions/variables
* mainIfAddr_default
* main_if_was_up
and functions with declarations but missing definitions
* hash_debug
* orig_find
* send_own_packet_work
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
BATMAN and broadcast packets are tracked with a sequence number window of
currently 64 entries to measure and avoid duplicates. Packets which have a
sequence number smaller than the newest received packet minus 64 are not
within this sequence number window anymore and are called "old packets"
from now on.
When old packets are received, the routing code assumes that the host of the
originator has been restarted. This assumption however might be wrong as
packets can also be delayed by NIC drivers, e.g. because of long queues or
collision detection in dense WiFi? environments. This behaviour can be
reproduced by doing a broadcast ping flood in a dense node environment.
The effect is that the sequence number window is jumping forth and back,
accepting and forwarding any packet (because packets are assumed to be "new")
and causing loops.
To overcome this problem, the sequence number handling has been reorganized.
When an old packet is received, the window is reset back only once. Other old
packets are dropped for (currently) 30 seconds to "protect" the new sequence
number and avoid the hopping as described above.
The reorganization brings some code cleanups (at least i hope you feel the
same) and also fixes a bug in count_real_packets() which falsely updated
the last_real_seqno for slightly older packets within the seqno window
if they are no duplicates.
This second version of the patch also fixes a problem where for seq_diff==64
bit_shift() reads from outside of the seqno window, and removes the loop
for seq_diff == -64 which was present in the first patch.
The third iteration also adds a window for the next expected sequence numbers.
This minimizes sequence number flapping for packets with very big differences
(e.g. 3 packets with seqno 0, 25000 and 50000 might still cause problems
without this window).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
| |
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
| |
batman-adv used its own logging infrastructure. Replace this with
standard kernel logging, printk(), with compile time and runtime
options to enable/disable different debug levels.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
B.A.T.M.A.N. (better approach to mobile ad-hoc networking) is
a routing protocol for multi-hop ad-hoc mesh networks. The
networks may be wired or wireless. See
http://www.open-mesh.org/ for more information and user space
tools.
This is the first submission for inclusion in staging.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
