| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Implement full support for OF SPI bindings. Now the driver can manage its
own chip selects without any help from the board files and/or fsl_soc
constructors.
The "legacy" code is well isolated and could be removed as time goes by.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The main purpose of this patch is to pass 'struct spi_device' to the chip
select handling routines. This is needed so that we could implement
full-fledged OpenFirmware support for this driver.
While at it, also:
- Replace two {de,activate}_cs routines by single cs_contol().
- Don't duplicate platform data callbacks in mpc83xx_spi struct.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The patch fixes following sparse warnings:
CHECK spi_mpc83xx.c
spi_mpc83xx.c:145:1: warning: symbol 'mpc83xx_spi_rx_buf_u8' was not declared. Should it be static?
spi_mpc83xx.c:146:1: warning: symbol 'mpc83xx_spi_rx_buf_u16' was not declared. Should it be static?
spi_mpc83xx.c:147:1: warning: symbol 'mpc83xx_spi_rx_buf_u32' was not declared. Should it be static?
spi_mpc83xx.c:148:1: warning: symbol 'mpc83xx_spi_tx_buf_u8' was not declared. Should it be static?
spi_mpc83xx.c:149:1: warning: symbol 'mpc83xx_spi_tx_buf_u16' was not declared. Should it be static?
spi_mpc83xx.c:150:1: warning: symbol 'mpc83xx_spi_tx_buf_u32' was not declared. Should it be static?
spi_mpc83xx.c:175:32: warning: incorrect type in initializer (different address spaces)
spi_mpc83xx.c:175:32: expected void *tmp_ptr
spi_mpc83xx.c:175:32: got unsigned int [noderef] <asn:2>*<noident>
spi_mpc83xx.c:183:26: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:183:26: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:183:26: got void *tmp_ptr
spi_mpc83xx.c:184:26: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:184:26: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:184:26: got void *tmp_ptr
spi_mpc83xx.c:287:31: warning: incorrect type in initializer (different address spaces)
spi_mpc83xx.c:287:31: expected void *tmp_ptr
spi_mpc83xx.c:287:31: got unsigned int [noderef] <asn:2>*<noident>
spi_mpc83xx.c:295:25: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:295:25: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:295:25: got void *tmp_ptr
spi_mpc83xx.c:296:25: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:296:25: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:296:25: got void *tmp_ptr
spi_mpc83xx.c:486:13: warning: symbol 'mpc83xx_spi_irq' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|\
| |
| |
| |
| |
| | |
Manual merge of:
arch/powerpc/include/asm/elf.h
drivers/i2c/busses/i2c-mpc.c
|
| |\
| | |
| | |
| | |
| | | |
Conflicts:
sound/soc/pxa/pxa2xx-i2s.c
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Cc: dbrownell@users.sourceforge.net
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
|
| |\ \
| | | |
| | | |
| | | |
| | | |
| | | | |
Conflicts:
arch/arm/mach-omap2/clock.c
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
... which now means no driver requests the "armxor_ck" clock directly.
Also, fix the error handling for clk_get(), ensuring that we propagate
the error returned from clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
... rather than the clock names themselves.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |\ \ \
| | | |/
| | |/|
| | | |
| | | |
| | | | |
Conflicts:
arch/arm/mach-at91/gpio.c
|
| | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
| |/
|/|
| |
| |
| |
| |
| |
| |
| | |
The driver was not releasing memory when it was removed or
when there was a failure during probe. This fixes it.
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|/
|
|
|
|
|
|
|
|
| |
gpio_get_value() returns 0 or nonzero, but getmiso() expects 0 or 1.
Sanitize the value to a 0/1 boolean.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
|
| |
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For some reason I have to slowdown clock to touchscreen device.
In atmel_spi_setup() there is comment that max_speed_hz == 0 means as slow
as possible and divider is set to maximum value. But in
atmel_spi_transfer() function is check against not zero max_speed_hz with
EINVAL returned.
Probably driver should setup divider for each transfer based on
transfer->speed_hz value, but I think that would be not necessary overhead
as all used devices have constant clock.
Below patch works fine for me.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
|
|
| |
The driver was updated to use the device tree rather than the platform data.
Signed-off-by: John Linn <john.linn@xilinx.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This fixes a byteswap bug in the LM70 temperature sensor driver,
which was previously covered up by a converse bug in the driver
for the LM70EVAL-LLP board (which is also fixed).
Other fixes: doc updates, remove an annoying msleep(), and improve
three-wire protocol handling.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
[ dbrownell@users.sourceforge.net: doc and whitespace tweaks ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (60 commits)
uio: make uio_info's name and version const
UIO: Documentation for UIO ioport info handling
UIO: Pass information about ioports to userspace (V2)
UIO: uio_pdrv_genirq: allow custom irq_flags
UIO: use pci_ioremap_bar() in drivers/uio
arm: struct device - replace bus_id with dev_name(), dev_set_name()
libata: struct device - replace bus_id with dev_name(), dev_set_name()
avr: struct device - replace bus_id with dev_name(), dev_set_name()
block: struct device - replace bus_id with dev_name(), dev_set_name()
chris: struct device - replace bus_id with dev_name(), dev_set_name()
dmi: struct device - replace bus_id with dev_name(), dev_set_name()
gadget: struct device - replace bus_id with dev_name(), dev_set_name()
gpio: struct device - replace bus_id with dev_name(), dev_set_name()
gpu: struct device - replace bus_id with dev_name(), dev_set_name()
hwmon: struct device - replace bus_id with dev_name(), dev_set_name()
i2o: struct device - replace bus_id with dev_name(), dev_set_name()
IA64: struct device - replace bus_id with dev_name(), dev_set_name()
i7300_idle: struct device - replace bus_id with dev_name(), dev_set_name()
infiniband: struct device - replace bus_id with dev_name(), dev_set_name()
ISDN: struct device - replace bus_id with dev_name(), dev_set_name()
...
|
| |
| |
| |
| |
| |
| | |
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Change the spi_s3c2410 driver to use the generic gpio calls that are now
available.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This solves several issues:
* It fixes the wrong idle clock polarity issue in a cleaner and less
expensive way.
* It handles the AT32AP7000 errata "SPI Chip Select 0 BITS field
overrides other Chip Selects". Other chips, e.g. AT91SAM9261, have
similar issues.
Currently, the AT91RM9200 code path is left alone. But it might be
interesting to try the same technique on RM9200 using a different CSR
register.
[dbrownell@users.sourceforge.net: restore debug message for activation]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, we have a flag called "new_1" which is basically equivalent
to cpu_is_at91rm9200(). The latter is also called directly a few places.
Clean up this mess by introducing a atmel_spi_v2() function for
determining the controller version, and move all version dependent code
over to use it. This allows us to remove the new_1 flag.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as
"spi_gpio", so it works with arbitrary GPIOs and can be configured through
platform_data. Such SPI masters support:
- any number of bus instances (bus_num is the platform_device.id)
- any number of chipselects (one GPIO per spi_device)
- all four SPI_MODE values, and SPI_CS_HIGH
- i/o word sizes from 1 to 32 bits;
- devices configured as with any other spi_master controller
When configured using platform_data, this provides relatively low clock
rates. On platforms that support inlined GPIO calls, significantly
improved transfer speeds are also possible with a semi-custom driver.
(It's still painful when accessing flash memory, but less so.)
Sanity checked by using this version to replace both native controllers on
a board with six different SPI slaves, relying on three different
SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Magnus Damm <damm@igel.co.jp>
Cc: Torgil Svensson <torgil.svensson@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The spi master driver must have num_chipselect set to allow the bus to
initialise. Pass this through the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The spidev_to_sg() call in spi_s3c24xx_gpio.c was using the wrong method
to convert the spi device into the private data for the driver. Fix this
by using spi_master_get_devdata.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads. Tested with mmc-spi.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Corrects spi_imx driver oops during initialization/probing: can't use
drv_data before it's allocated.
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
According to the manual the "tdfOnExit" flag must be set on the last byte
we want to send. The PSC controller holds SS low until the flag is set.
However, the flag was set always on the last byte of the FIFO,
independently if it is the last byte of the transfer. This generates
spurious toggling of the SS signals that breaks the protocol of some
peripherals. Fix.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
I saw a kernel oops in spidev_remove() when a spidev device was registered
and I unloaded the SPI master driver:
Unable to handle kernel paging request for data at address 0x00000004
Faulting instruction address: 0xc01c0c50
Oops: Kernel access of bad area, sig: 11 [#1]
CDSPR
Modules linked in: spi_ppc4xx(-)
NIP: c01c0c50 LR: c01bf9e4 CTR: c01c0c34
REGS: cec89c30 TRAP: 0300 Not tainted (2.6.27.3izt)
MSR: 00021000 <ME> CR: 24000228 XER: 20000007
DEAR: 00000004, ESR: 00800000
TASK = cf889040[2070] 'rmmod' THREAD: cec88000
GPR00: 00000000 cec89ce0 cf889040 cec8e000 00000004 cec8e000 ffffffff 00000000
GPR08: 0000001c c0336380 00000000 c01c0c34 00000001 1001a338 100e0000 100df49c
GPR16: 100b54c0 100df49c 100ddd20 100f05a8 100b5340 100efd68 00000000 00000000
GPR24: 100ec008 100f0428 c0327788 c0327794 cec8e0ac cec8e000 c0336380 00000000
NIP [c01c0c50] spidev_remove+0x1c/0xe4
LR [c01bf9e4] spi_drv_remove+0x2c/0x3c
Call Trace:
[cec89d00] [c01bf9e4] spi_drv_remove+0x2c/0x3c
[cec89d10] [c01859a0] __device_release_driver+0x78/0xb4
[cec89d20] [c0185ab0] device_release_driver+0x28/0x44
[cec89d40] [c0184be8] bus_remove_device+0xac/0xd8
[cec89d60] [c0183094] device_del+0x100/0x194
[cec89d80] [c0183140] device_unregister+0x18/0x30
[cec89da0] [c01bf30c] __unregister+0x20/0x34
[cec89db0] [c0182778] device_for_each_child+0x38/0x74
[cec89de0] [c01bf2d0] spi_unregister_master+0x28/0x44
[cec89e00] [c01bfeac] spi_bitbang_stop+0x1c/0x58
[cec89e20] [d908a5e0] spi_ppc4xx_of_remove+0x24/0x7c [spi_ppc4xx]
[...]
IMHO a call to spi_set_drvdata() is missing in spidev_probe(). The patch
below helped.
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|\ \ |
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Move plat/regs-spi.h to arch/arm/plat-s3c/include/plat ready
ready to clean out old include directories.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
| |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads.
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fixes a data corruption bug in pxa2xx_spi.c when operating in full duplex
mode with DMA and using buffers that overlap.
SPI transmit and receive buffers are allowed to be the same or to overlap.
However, this driver fails if such overlap is attempted in DMA mode
because it maps the rx and tx buffers in the wrong order. By mapping
DMA_FROM_DEVICE (read) before DMA_TO_DEVICE (write), it invalidates the
cache before flushing it, thus discarding data which should have been
transmitted.
The patch corrects the order of mapping. This bug exists in all versions
of pxa2xx_spi.c; similar bugs are in the drivers for two other SPI
controllers (au1500, imx).
A version of this patch has been tested on kernel 2.6.20 using
verification of loopback data with: random transfer length, random
bits-per-word, random positive offsets (both larger and smaller than
transfer length) between the start of the rx and tx buffers, and varying
clock rates.
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: J. Scott Merritt <merrij3@rpi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
controller
We're working with an AT91SAM9263 Rev B in our design and I experienced
some inconsistency in spi-based touchscreen usage between our board and
the Atmel evaluation kit we have that runs on a Rev A chip.
The data was apparently delayed by 1 byte and got ridiculous data out of
the touchscreen driver, very strange. As everything looked normal in
the spi, touchscreen and dma logs, I contacted the Atmel support and
they triggered me on a new HW bug that appeared in the Rev B SPI
controller.
The problem is that the SPI controller on the Rev B needs that the
software reset is performed two times so that it's performed correctly.
Applying the patch below solves the issue on my Rev B board. I've tested
it as well on my Rev A evaluation kit and it has apparently no unwanted
side effect, things continue to work as expected.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
|
| |
| |
| |
| |
| |
| |
| |
| | |
Now that device_create() has been audited, rename things back to the
original call to be sane.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (51 commits)
[ARM] 5308/1: Fix Viper ISA IRQ handling
[ARM] 5307/1: pxa: fix CM-X2XX PCMCIA build error
[ARM] 5306/1: pxa: fix build error on CM-X270
[ARM] 5302/1: ARM: OMAP: Revert omap3 WDT changes to avoid merge conflict
[ARM] 5305/1: ARM: OMAP: Fix compile of McBSP by removing unnecessary check
[ARM] 5301/1: ARM: OMAP: Add missing irq defines
ARM: OMAP3: Add default kernel config for OMAP LDP
ARM: OMAP3: Add basic board support for OMAP LDP
ARM: OMAP3: Defconfig for the Gumstix Overo board (rev 3)
ARM: OMAP3: Add support for the Gumstix Overo board (rev 3)
ARM: OMAP3: Add Beagle defconfig
ARM: OMAP3: Add minimal Beagle board support
ARM: OMAP3: Add minimal omap3430 support
ARM: OMAP2: Fix sparse, checkpatch warnings in OMAP2/3 IRQ code
ARM: OMAP: Fixes to omap_mcbsp_request function
ARM: OMAP: Add support for OMAP2430 in McBSP
ARM: OMAP: Add support for McBSP devices 3 - 5 on 34xx
ARM: OMAP: Allocate McBSP devices dynamically
Fix sections for omap-mcbsp platform driver
[ARM] S3C24XX: Additional include moves
...
|
| |\ \
| | | |
| | | |
| | | |
| | | |
| | | | |
Conflicts:
arch/arm/mach-versatile/core.c
|
| |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Conflicts:
arch/arm/mach-omap2/gpmc.c
arch/arm/mach-omap2/irq.c
|
| | | | |
| | | | |
| | | | |
| | | | | |
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
When omap_udc is also incorporated, this macro will no longer be used.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Make the SPI external GPIO expander drivers register themselves at
subsys_initcall() time when they're statically linked, and make the SPI
core do its driver model initialization earlier so that's safe.
SOC-integrated GPIOs are available starting very early -- often before
initcalls start to run, or earily in arch_initcall() at latest -- so this
improves consistency, letting more subsystems rely on GPIOs being usable
by their own subsys_initcall() code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Add support to orion_spi for the 88F6183 ARM SoC by adding code to work
around a 6183-specific erratum.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Make the chip info structure data optional by providing reasonable
defaults. Improve corresponding documentation, and highlight the drawback
of not providing explicit chipselect control.
DMA can determine appropriate dma_burst_size and thresholds automatically
so use DMA even if dma_burst_size is not specified.
Signed-off-by: Vernon Sauder <VernonInHand@gmail.com>
Reviewed-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Minor fixes: remove redundant local variable initialization, fix "can not"
to what I _think_ is a preferred spelling, output IRQ number if requesting
it failed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Add a pin configuration callback for the s3c24xx SPI driver, as there are
several options depending on the channel and the chip in use.
This is needed as the controller may not have been setup by the initial
bootloader and the fact that the SPI controller gets reset over
suspend/resume into slave mode but the GPIO function registers do not.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Modify spi_write_then_read() to use one transfer. This speeds up all
callers, and is a minor code shrink.
Signed-off-by: Vernon Sauder <Vernon.Sauder@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|