| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| ... | |
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Due to the full duplex nature of the SPI bus, the SPI master
on DaVinci needs transmit to be active even if the tranfer is
only meant to collect receive data.
The current code achieves this by using a temporary zeroed buffer
to provide DMA data in case the transfer does not have a transmit
buffer provided.
However, the transmit DMA is started only if transmit buffer is
provided rendering the temporary buffer unused. Instead the code
relies on a write to SPIDAT1 register to trigger transmit operation.
This however only sends two bytes of data.
Fix this by starting transmit DMA always.
This changes exposes a bug on DM355 where the CSHOLD bit in
SPIDAT1 needs to be written to in between transfers. Handle
that by introducing a "cshold_bug" platform data which is
set to true for DM355.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Do not store DMA channel related information per chip-select since
that information does not depend on the chip select.
The same DMA channels can be used for transfers on all chip-selects
since the transfer happens one-at-a-time.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Remove unnecessary call to davinci_spi_setup_transfer() at the end
of davinci_spi_setup().
davinci_spi_setup_transfer() is registered as the setup_transfer
callback for the bitbang layer and is called independently by
the bitbang layer to setup the transfer before it begins.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The function davinci_spi_bufs_prep() is doing stuff that
davinci_spi_setup() is doing. Eliminate it and move the work
to davinci_spi_setup()
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Configure the data-in, data-out and clock functionality pins
in SPIPC0 register only once during probe. No need to set these
bits for each transfer.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Add support for SPI interrupt mode operation.
Define a per chip-select "io type" variable which
specifies if the transfers on this chip-select should
happen in interrupt mode or polled mode.
Introduce a new function davinci_spi_process_events()
to help consolidate the code between interrupt mode
processing and polled mode processing.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Use the fact that the get_tx and get_rx can now cope with
NULL buffer pointers to simplify the poll mode transfer
code.
While at it, check for SPI errors every transfer rather than
at the end of the whole transfer.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The interrupt mode support as it stands is another version
of poll mode. Even when interrupt mode is selected, the code
tight loops on interrupt status register, rendering it totally
useless. A completion variable is initialized, but never used.
Remove this fake interrupt mode since users can anyway use
poll mode with no functional difference. A usefully implemented
interrupt mode support can be added later.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The completion variable 'done' is unnecessarly initialized by
the function davinci_spi_bufs_dma() where as it is not used
for DMA transfers at all.
Remove the unnecessary initialization.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
In davinci_spi_check_error(), Tx interrupt being set is
treated as error. This function is only meant to flag
bus error conditions and Tx interrupt being set at that
point is not a bus error but rather a driver bug.
Stop checking for Tx interrupt and flagging that as an
IO error.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The variable count in DaVinci SPI driver's private data is
largely unused and its minor use can easily be eliminated.
Remove the variable.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
In the davinci_spi_bufs_dma() function, SPI is briefly disabled
before enabling it immediately back again.
Remove this unnecessary disable.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
In the davinci_spi_{tx|rx}_u{8|16}() functions, check for
buffer pointer being valid before using it. While providing
for better error checking, this change will help simplify
code in the caller.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The EDMA acount (called data_type in davinci_spi_bufs_dma())
is simply the bytes_per_word obtained in the transfer setup
function. The current code calculates the acount value from
bytes_per_word in a convoluted manner. Simplify the code.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The count member of davinci_spi is internal to the driver and
is not shared with framework. Eliminate its unnecessary update.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The struct davinci_spi_slave has a single member. Eliminate it
and store the per-chipselect data in struct davinci_spi directly.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Several members of struct davinci_spi_slave are unused in code.
Remove such members.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Just enabling WAITENA in SPIFMTn register waits for the
enable signal from the slave indefinitely. Allow support
for finite waiting by adding support for c2e delay
(maximum time for addressed slave to respond) and t2e
delay (maximum time for slave to respond after transmit
data finished).
While at it, modify the T2C and C2T defines by prepending
the register name as is the convention followed for other
register field elsewhere in the driver.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Setup chip-select timers values only if timer is enabled
(timer_disbled in spi configuration is false).
As a nice side effect, this patch removes code duplicated in
davinci_spi_bufs_pio() and davinci_spi_bufs_dma().
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Consolidate the setup of SPIFMTn register under
davinci_spi_setup_transfer() simplifying the code
and avoiding unnecessary reads and writes to the
register.
The two inline functions {set|clear}_fmt_bits() can
be eliminated because of this.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Some chip-select specific paramterers like wdelay, parity, usage of
chip-select timers (and the actual timer values) are included in
platform data forcing the same behaviour across all chip-selects.
Create a new davinci_spi_config data structure which can be passed
along using controller_data member of spi_device data structure
on a per-device basis.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The SPI_READY bit of struct spi_device:mode serves the purpose
of letting the SPI master know if the slave can signal if it is
ready for transfer or not.
The 'wait_enable' platform data was duplicating this functionality.
Use the framework provided method of indicating this capability.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Simplify pre-scalar calculation and move it into a seprate
function.
Refuse to correct invalid pre-scalar values silently as this
might lead to unexpected bugs and lower performance. Instead
an error will force users to dig into the root-cause of the
issue.
While at it, remove some device specific checks on the maximum
SPI frequency. As the driver supports the SPI interface
implemented on various devices, it should only take care of core
SPI limitations and leave the device specific handling to platform
code.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Sometimes, the chip selects provided by SPI module are
muxed with other functionality and cannot be used in
some designs. In such cases, it becomes convenient to use
an available GPIO line as chip select.
This patch enables the DaVinci SPI driver to treat specific
GPIO lines as chip selects based on information provided in
platform data.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
On TI DaVinci's SPI controller, the SPIDAT1 register which
controls the chip slect status, also has data transmit register
in the lower 16 bits. Writing to the whole 32-bits triggers
an additional data transmit every time the chip select is disabled.
While most SPI slaves cope-up with this, some cannot. This
patch fixes this by doing a 16-bit write on the upper half
of the SPIDAT1 register
While at it, group the SPIGCR1 register related defines seperately
from SPIDAT1 register defines.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Let davinci_spi_chipselect() perform both activation and
deactivation of chip selects. This lets spi_bitbang fully
control chip select activation, as intended by the SPI API.
With this change, the chip select activation code need not
be duplicated in davinci_spi_bufs_{pio|dma}().
Also, keeping chip select active control is removed as a
platform data and simply controlled using information from
spi_bitbang on whether chip slect should be activated or
de-activated.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Quit writing the same constant value determining the chip-select
mode when no transmissions are in progress in davinci_spi_chipelect().
Instead just setup the SPIDEF register once during probe.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The typecasting of SPI base address to davinci_spi_reg is
unused.
Remove it.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Remove unused defines from code which should help
in easy reading of code.
Also, use the opportuinity to keep the SPIGCR1
register defines together.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The 'pdata' variable is unused in couple of routines.
Remove such occurences.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Cleanup unnecessary white space from various
parts of the file.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | |/ / / /
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Fix the following checkpatch error:
WARNING: unnecessary whitespace before a quoted newline
+ dev_info(&pdev->dev, "Controller at 0x%p \n", davinci_spi->base);
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Probe/remove should be in __devinit/__devexit. Found by a section-mismatch
warning. Also, copy do_remove() over to remove().
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
dw_spi driver in upstream only supports PIO mode, and this patch
will support it to cowork with the Designware dma controller used
on Intel Moorestown platform, at the same time it provides a general
framework to support dw_spi core to cowork with dma controllers on
other platforms
It has been tested with a Option GTM501L 3G modem and Infenion 60x60
modem. To use DMA mode, DMA controller 2 of Moorestown has to be enabled
Also change the dma interface suggested by Linus Walleij.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
[Typo fix and renames to match intel_mid_dma renaming]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The SPI polling loop timeout only works with HZ=100 as the loop was
actually too short.
Also add appropriate cpu_relax() in the busy wait loops...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This variable is a bool but defined an int and defined completely
backwards. This makes the code more readable.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The sglen return by the dma_map_sg() should be passed to the DMA
engine, not the one passed in. If we one day have a DMA mapper
that can coalesce entries, this will bug due to a too large
number of entries being passed in.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The struct device for the DMA engine is the apropriate one to use
when mapping/unmapping buffers. This is because the memory which
is addressable by DMA is determined by the DMA engine rather than
the device.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
It seems spi_topcliff_pch of linux-2.6.37-rc6 degraded by previous patch.
In fact, data transfer fails on evaluation board testing.
I found like the following register miss-setting line.
Using this patch, I have confirmed data transfer can work well.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
There are no machines in-tree that still use the driver
name as device name. So save a few bytes and remove it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | |\ \ \ \ \
| | | |_|_|/
| | |/| | | |
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Now that the of_platform_bus_type has been merged with the platform
bus type, a single platform driver can handle both OF and non-OF use
cases. This patch merges the OF support into the platform driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This patch merges the platform driver support into the main body of
xilinx_spi.c in preparation for merging the OF and non-OF support
code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
|
| | | |/ / /
| |/| | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The current code has the OF binding modifying the platform_data
pointer which it must not do, and the common code doesn't really need
to use a pdata pointer. This patch eliminates the platform_data
references from the common part of the driver in preparation for
merging the OF and non-OF versions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
After grabbing a msg from the msgq, the mcfqspi_work function calls
list_del_init on the mcfqspi->msgq which unintentionally deletes the rest
of the list before it can be processed. If qspi call was made using
spi_sync, this can result in a process hang.
Signed-off-by: Jate Sujjavanich <jsujjavanich@syntech-fuelmaster.com>
Acked-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
When SPI wake up from OFF mode, CS is in the wrong state: force it to the
inactive state.
During the system life, I monitored the CS behavior using a oscilloscope.
I also activated debug in omap2_mcspi, so I saw when driver disable the clocks
and restore context when device is not used.Each time the CS was in the correct
state. It was only when system was put suspend to ram with off-mode activated
that on resume the CS was in wrong state( ie activated).
Changelog:
* Change from v1 to v2:
- Rebase on linus/master (after 2.6.37-rc1)
- Do some clean-up and fix indentation on both patches
- Add more explanations for patch 2
* Change from v2 to v3:
- Use directly resume function of spi_master instead of using function
- from spi_device as Grant Likely pointed it out.
- Force this transition explicitly for each CS used by a device.
* Change from v3 to v4:
- Patch clean-up according to Kevin Hilman and checkpatch.
- Now force CS to be in inactive state only if it was inactive when it was
suspended.
* Change from v4 to v5:
- Rebase on linus/master (after 2.6.37-rc3)
- Collapse some lines as pointed by Grant Likely
- Fix a spelling
* Change from v5 to v6:
- Rebase on linus/master (after 2.6.37-rc7)
- Use CONFIG_SUSPEND instead of CONFIG_PM
- Didn't use legacy PM methods anymore. Instead, add a struct dev_pm_ops and
add the resume method there.
- Fix multi-line comment style
* Change from v6 to v7:
- Rebase on linus/master (after 2.6.37-rc8)
- Drop an extra line
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| |\ \ \ \ \
| |_|_|/ /
|/| | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
spi/mpc52xx-spi: fix annotation for remove()-pointer
spi/fsl_espi: fix wrong setting of the address in the command buffer
spi/fsl_espi: change the read behaviour of the SPIRF
of/i2c: Fix request module by alias
powerpc/mpc5200: include fs.h in mpc52xx_gpt.c
|
