summaryrefslogtreecommitdiffstats
path: root/drivers/scsi/bfa/bfa_ioc.h
Commit message (Collapse)AuthorAgeFilesLines
* [SCSI] bfa: fru vpd date update changesVijaya Mohan Guvva2013-06-261-1/+2
| | | | | | | | | | | | | 1. While FRU VPD data update, inform firmware to send a completion event on I2C bus. Without this change, firmware used to send completion message on I2C bus for every chunk of FRU VPD update. 2. Support for FRU VPN update on CHINOOK2 cards. 3. Append port count to the model name to differentiate between single port and dual port model of 1860. 4. Update the size of the model name to 16bytes Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: kdump fix on 815 and 825 adaptersVijaya Mohan Guvva2013-06-261-0/+6
| | | | | | | | | | | | | | | | Root cause: When kernel crashes, On brocade 815/825 adapters, bfa IOC state machine and FW doesn't get a notification and hence are not cleanly shutdown. So registers holding driver/IOC state information are not reset back to valid disabled/parking values. This causes subsequent driver initialization to fail during kdump kernel boot. Fix description: during the initialization of first PCI function, reset corresponding register when unclean shutown is detect by reading chip registers. This will make sure that ioc/fw gets clean re-initialization. Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Add support to read/update the FRU data.Krishna Gudipati2012-10-071-0/+49
| | | | | | | | | - Add FRU sub-module to support FRU read/write/update. - Add support to read/write from the temp FRU module. [jejb: fix checkpatch issues] Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Add support to configure min/max bandwidth for a pcifnKrishna Gudipati2012-10-071-4/+4
| | | | | | | | | | - Added support to configure minimum bandwidth for a pcifn. - Minimum bandwith is guaranteed at per queue level. - Added support to update pcifn bandwidth dynamically without a server reboot. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Add support for IO throttling at port levelKrishna Gudipati2012-10-071-0/+3
| | | | | | | | | Add capability to limit the number of exchanges on a port to avoid queue-full conditions from the target side. Signed-off-by: Sudarsana Reddy Kalluru <skalluru@brocade.com> Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Fix few attributes in the RHBA CT passthru commandKrishna Gudipati2012-10-071-1/+2
| | | | | | | | | | | - Made changes to set the RHBA command max payload based on the port configured frame size. - Made changes to fix the driver/fw version size in FMDI structure. - Fix to pass the fw version for FDMI attribute type FDMI_HBA_ATTRIB_FW_VERSION rather than driver version. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* Merge tag 'scsi-for-linus' of ↵Linus Torvalds2012-10-021-0/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull first round of SCSI updates from James Bottomley: "This is a large set of updates, mostly for drivers (qla2xxx [including support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas). There's also a rework for tape adding virtually unlimited numbers of tape drives plus a set of dif fixes for sd and a fix for a live lock on hot remove of SCSI devices. This round includes a signed tag pull of isci-for-3.6 Signed-off-by: James Bottomley <JBottomley@Parallels.com>" Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI helper function use in a function that was removed by this pull. * tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits) [SCSI] st: remove st_mutex [SCSI] sd: Ensure we correctly disable devices with unknown protection type [SCSI] hpsa: gen8plus Smart Array IDs [SCSI] qla4xxx: Update driver version to 5.03.00-k1 [SCSI] qla4xxx: Disable generating pause frames for ISP83XX [SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX [SCSI] qla4xxx: IDC implementation for Loopback [SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx [SCSI] qla4xxx: Fix panic while rmmod [SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails [SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX [SCSI] qla4xxx: Update idc reg in case of PCI AER [SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery [SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX [SCSI] qla4xxx: Print correct IDC version [SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW [SCSI] scsi_dh_alua: Enable STPG for unavailable ports [SCSI] scsi_remove_target: fix softlockup regression on hot remove [SCSI] ibmvscsi: Fix host config length field overflow [SCSI] ibmvscsi: Remove backend abstraction ...
| * [SCSI] bfa: Add PowerPC support and enable PCIE AER handling.Krishna Gudipati2012-09-241-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | - Added few missing endian swap changes to support BFA on PowerPC. - Added PCIE AER support to BFA: a) Implemented the PCI error handler entry points. b) Made changes to FCS state machine to handle STOP event from the PCI error detected entry point. c) Made changes to the IO Controller state machine to handle SUSPEND event from the PCI error detected entry point. d) Made changes to restart the BFA operations on a slot_reset completion. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* | treewide: fix comment/printk/variable typosAnatol Pomozov2012-09-011-1/+1
|/ | | | | Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* [SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.Krishna Gudipati2012-03-281-1/+16
| | | | | | | | | | Made changes to the Fabric Assigned Address(FAA) feature implementation. Introduced the IOCFC state machine, which now handles the FAA logic, IOC and BFA sub-modules enablement. Removed un-wanted FAA enable/disable routines; FAA is enabled by default. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Add support to store driver configuration in flash.Krishna Gudipati2011-07-271-1/+43
| | | | | | | | | | | - Added dconf (Driver Config) BFA sub-module. - The dconf sub-module provides interfaces and manages flash writes to the flash DRV parition. - dconf sub-module also ensures that the whole 64K DRV partition is updated on a flash write. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Added support to collect and reset fcport statsKrishna Gudipati2011-07-271-0/+2
| | | | | | | | | | | - Added support to collect and reset fcport stats. - Modified design to allow multiple requests for fcport stats. - fcport will remember the stats request in its stats_pending queue and service each of the queued requests after receiving a firmware response for the prior request. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Add FC-transport based Asynchronous Event Notification support.Krishna Gudipati2011-07-271-0/+2
| | | | | | | | - Added support to post vendor unique events on fc_host. - Supports adapter, port, ioc, flash and remote port based AEN events. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Added support to query PHY.Krishna Gudipati2011-06-291-0/+54
| | | | | | | | | - Added PHY sub-module. - Implemented interface to obtain stats and to read/update the fw from the PHY module. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Added HBA diagnostics support.Krishna Gudipati2011-06-291-0/+141
| | | | | | | | | - Added diagnostics sub-module to BFA. - Implemented interface to perform memtest/loopback test and some other diagnostics tests. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Added support for flash configurationKrishna Gudipati2011-06-291-0/+72
| | | | | | | | - Added flash sub-module. - Implemented the interface to read/erase/update flash partition. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Added support to obtain SFP info.Krishna Gudipati2011-06-291-0/+52
| | | | | | | | - Added SFP sub-module to BFA. - Added interface to collect sfp media info and sfp speed. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: DMA memory allocation enhancement.Krishna Gudipati2011-06-291-0/+64
| | | | | | | | | | | | | - Modified the design such that each BFA sub-module will provide the amount of DMA and KVA memory needed by it and queues the same request to the global dma and kva info queues. - During the memory allocation we iterate over this queue to allocate the dma and kva memory requested by sub-modules. - The change is needed to avoid requesting the aggregate amount of memory needed by all the BFA sub-modules as one contiguous chunk. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Brocade-1860 Fabric Adapter PLL init fixes.Krishna Gudipati2011-06-291-2/+1
| | | | | | | | | | | | | | | | | | - If flash controller is halted unconditionally, this results in illegal write access to flash controller register domain. Since flash controller registers are only accessible once s_clk is started - added logic to check for WGN status and halt flash controller only if it is already running. - Added check to wait for flash controller halt to be completed before proceeding with s_clk/l_clk initializations. - Removed unnecessary reset logic for PMM 1T memory and moved memory initialization after flash access enable. - Disable Brocade-1860 asic MBOX interrupt before PLL initialization. - Remove reset enable for S_CLK/L_CLK after both PLL initializations are complete. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Added Fabric Assigned Address(FAA) supportKrishna Gudipati2011-06-291-0/+1
| | | | | | | | | - Updated/added data structures and definitions to support FAA protocol. - Modified the IOC state machine to support FAA. - Introduced FAA feature configuration - enable/disable/query. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Enable ASIC block configuration and query.Krishna Gudipati2011-06-291-0/+49
| | | | | | | | | | - Added ASIC block configuration APIs: - to create/delete/update the physical functions - to do adapter/port mode configuration - to query the current ASIC block configuration. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Driver initialization and model description fixKrishna Gudipati2011-06-291-2/+2
| | | | | | | | | | | | | | - Moved FCS initialization, which internally does the im_port creation as well as the scsi_host creation before bfa_init. Once the bfa_init is complete & successful: - Reset the FCS base port cfg params such as pwwn/nwwn and setup fc host params - based on the values learned during the ioc getattr request. - Change needed to support BSG commands even on bfa init failure. - Model description fixes for Brocade adapters. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Brocade-1860 Fabric Adapter 16Gbs support and flash controller ↵Krishna Gudipati2011-06-291-1/+6
| | | | | | | | | | | | | | | | | | fixes. - Added support for 16Gbps. - Added logic to flush pending mailbox command queue when IOC is disabled. - Fix to Halt the flash controller during fw initialization - since when asic blck is programmed flash controller's continuous access blocks f/w access to flash. - Added new asic based card types and modified IOC get card model routine. - Added PLL init fix to do LPU reset every time we do a memory initialization, since not doing so will cause LPU to be uninitialized during driver load. - Added fix to Halt flash controller before PLL initialization. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: IOC and PLL init changes for Brocade-1860 Fabric Adapter.Krishna Gudipati2011-06-291-1/+2
| | | | | | | | | | | | | | | | | - Introduced IOC poll mechanism which replaces current interrupt based FW READY method. - The timer based poll routine in IOC will query the ioc_fwstate register to see if there is a state change in FW, and sends the READY event. - Bug fixes in the new asic PLL initialization. - Added logic to handle CPE/RME queue interrupts before iocfc config done. 1. Use the queue_process flag to see if iocfc configuration is done in INTX mode. 2. Split the MSIX handler installation in two - one for IOC intr handler and the other for cpe/rme queue handler - and delay assigning queue handlers until iocfc config is done in MSIX mode. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Brocade-1860 Fabric Adapter Hardware EnablementKrishna Gudipati2011-06-291-48/+69
| | | | | | | | | | | | | | | | - Added support for Brocade-1860 Fabric Adapter. - Made changes to support single firmware image per asic type. - Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with only minimal defines used by host. - Added changes to setup CPE/RME Queue register offsets based on firmware response. - Removed queue register offset initializations and added register offsets to BFI config response message. - Added Brocade-1860 asic specific interrupt status definitions and mailbox interfaces. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Introduce IOC event notification mechanism.Krishna Gudipati2011-06-291-8/+16
| | | | | | | | | Introduced a generic event notification callback function that receives IOC_ENABLED, IOC_DISABLED, IOC_FAILED events and notifies the modules registered for these events. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: Introduced generic address len pair to represent DMA memory chunk.Krishna Gudipati2011-06-291-12/+10
| | | | | | | | | | | - Avoid the use of hardware defined structure bfi_sge_s for DMA requests in host. - Defined a generic address len pair to represent a DMA memory chunk (bfi_alen_s). Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* [SCSI] bfa: kdump fixJing Huang2011-05-241-0/+1
| | | | | | | | | | | | | | | Root cause: When kernel crashes, bfa IOC state machine and FW doesn't get a notification and hence are not cleanly shutdown. So registers holding driver/IOC state information are not reset back to valid disabled/parking values. This causes subsequent driver initialization to hang during kdump kernel boot. Fix description: during the initialization of first PCI function, reset corresponding register when unclean shutown is detect by reading chip registers. This will make sure that ioc/fw gets clean re-initialization. Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <jbottomley@parallels.com>
* [SCSI] bfa: remove unused defintions and misc cleanupsJing Huang2010-12-311-9/+0
| | | | | | | | This patch removes unused functions, data strucutres, and definitions. It also includes misc comment and formatting cleanups. Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: IOC auto recovery fix.Krishna Gudipati2010-12-211-1/+18
| | | | | | | | | | - Made IOC auto_recovery synchronized and not timer based. - Only one PCI function will attempt to recover and reinitialize the ASIC on a failure, after all the active PCI fns acknowledge the IOC failure. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: remove all OS wrappersMaggie Zhang2010-12-211-4/+4
| | | | | | | | Remove OS wrapper functions/macros, and as a result remove bfa_os_inc.h. Signed-off-by: Maggie Zhang <xmzhang@brocade.com> Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: clean up one line functionsMaggie Zhang2010-12-211-14/+5
| | | | | | | | Cleaned up one line functions. Signed-off-by: Maggie Zhang <xmzhang@brocade.com> Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: remove unused and empty functionsMaggie Zhang2010-12-211-1/+0
| | | | | | | | Removed unused and empty functions. Signed-off-by: Maggie Zhang <xmzhang@brocade.com> Signed-off-by: Jing Huang <xmzhang@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: fix endianess sparse check warningsMaggie2010-12-211-4/+4
| | | | | | | First round of fix for the endianess check warnings from make C=2 CF="-D__CHECK_ENDIAN__". Signed-off-by: Maggie <xmzhang@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: fix regular sparse check warnings.Maggie2010-12-211-1/+1
| | | | | | | Fix all sparse check warnings from make C=2. Signed-off-by: Maggie <xmzhang@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: fix comments for header filesJing Huang2010-10-251-19/+19
| | | | | | | | | | This patch addresses the comments from Randy Dunlap (Randy.Dunlap@oracle.com) regarding comment blocks that begining with "/**". bfa driver comments currently do not follow kernel-doc convention, we hence replace all /** with /* and **/ with */. Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: remove os wrapper functions and macrosJing Huang2010-10-251-34/+32
| | | | | | | | This patch replaces register access functions and macros with the the ones provided by linux. Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: replace endian swap macros with the ones provided by linuxJing Huang2010-10-251-2/+2
| | | | | Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: remove os wrapper and unused functionsJing Huang2010-10-251-1/+1
| | | | | | | | | | | This patch removes os wrapper and unused functions. bfa_os_assign(), bfa_os_memset(), bfa_os_memcpy(), bfa_os_udelay() bfa_os_vsprintf(), bfa_os_snprintf(), and bfa_os_get_clock() are replaced with direct assignment or native linux functions. Some unused functions related to VF (Vitual fabric) are also removed. Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: cleanup driverKrishna Gudipati2010-09-161-52/+196
| | | | | | | | We have flattened the BFA hierarchy and also reduced the number of source and header files we used to have earlier. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: update to support firmware configuationJing Huang2010-07-271-0/+1
| | | | | | | | Update related data structures to support firmeare configuration. Add AEN events related to firmware configuation. Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: ioc attributes fixJing Huang2010-07-271-0/+3
| | | | | | | | | | This patch fixes the APIs to obtain ioc attributes - fix API to obtain wwpn, wwnn, and mac. - add API to get mfg wwpn, wwnn, and mac. - fix API to obtain wwn of boot target. Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: enable basic PBC supportJing Huang2010-07-271-1/+0
| | | | | | | | | | | The patch includes the driver side changes to enable basic PBC (PreBoot Configuration) feature. - Data structure changes and new definitions for PBC. - APIs to access PBC info. - Remove unused code. Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: enable new hardwareJing Huang2010-07-271-3/+4
| | | | | | | | | | | | This patch enables support of new mezzanine cards for HP and IBM blade server. - Add new pciids for HP and IBM mezzanine card. - Add a new firmware image for HP mezzanine card, which is running in FC only mode. Rename firmware image to reflect the difference. Change the firmware download code accordingly for the above changes. Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: Replace bfa_get_attr() with specific APIsKrishna Gudipati2010-03-071-0/+10
| | | | | | | | | bfa_ioc_attr_s is a big structure and some times could cause stack overflow if defined locally, so add specific APIs that are needed to replace the use of ioc_attr local var. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: Added firmware save clear feature for BFA driver.Krishna Gudipati2010-03-071-0/+1
| | | | | Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: Clear LL_HALT and PSS_ERR bit when IOC crashes.Krishna Gudipati2010-03-071-0/+1
| | | | | | | Clear LL_HALT and PSS_ERR bit in the interrupt status register on an IOC crash. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: IOC changes: Support faster recovery and split bfa_ioc.c into ↵Krishna Gudipati2010-03-071-3/+42
| | | | | | | | | | | | | | | | | | | | | | | | | ASIC specific code. Add support for faster IOC recovery after failure. Split bfa_ioc.c into three files: bfa_ioc.c: Common code shared between crossbow and catapult ASIC's. bfa_ioc_cb.c: Code specific to the crossbow, reg mapping and interrupt related routines. bfa_ioc_ct.c: Code specific to the catapult, reg mapping and interrupt related routines. Fix to make sure IOC reinitialize's properly on enable request - update the ioc_fwstate reg with BFI_IOC_FAIL on ioc disable mbox cmd timeout. Makefile changes to support the 2 newly added files bfa_ioc_cb.c and bfa_ioc_ct.c. Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: fixed checkpatch errors for bfad filesJing Huang2009-12-041-6/+6
| | | | | | | This patch fixes checkpatch errors/warnings in bfad files. Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: Brocade BFA FC SCSI driverJing Huang2009-10-021-0/+259
Add new driver for Brocade Hardware Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
OpenPOWER on IntegriCloud