summaryrefslogtreecommitdiffstats
path: root/drivers/regulator/tps6507x-regulator.c
Commit message (Collapse)AuthorAgeFilesLines
* regulator: tps6507x: Use regulator_map_voltage_ascendAxel Lin2013-04-251-0/+1
| | | | | | | | All regulators have ascendant voltage list in this driver. Use regulator_map_voltage_ascend for them. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps6507x: Fix using wrong dev argument for calling of_regulator_matchAxel Lin2013-01-301-1/+1
| | | | | | | | | | | | The dev parameter is the device requesting the data. In this case it should be &pdev->dev rather than pdev->dev.parent. The dev parameter is used to call devm_kzalloc in of_get_regulator_init_data(), which means this fixes a memory leak because the memory is allocated every time probe() is called, thus it should be freed when this driver is unloaded. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps6507x: add device tree support.Vishwanathrao Badarkhe, Manish2013-01-271-0/+92
| | | | | | | | | | | Add device tree based initialization support for TI's tps6507x regulators. Add device tree binding document for TI's tps6507x using datasheet: http://www.ti.com/lit/ds/symlink/tps65070.pdf Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: remove use of __devexitBill Pemberton2012-11-201-1/+1
| | | | | | | | CONFIG_HOTPLUG is going away as an option so __devexit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: remove use of __devinitBill Pemberton2012-11-201-1/+1
| | | | | | | | CONFIG_HOTPLUG is going away as an option so __devinit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: remove use of __devexit_pBill Pemberton2012-11-201-1/+1
| | | | | | | | CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps6507x: Avoid duplicating the same mapping table for LDO2 and ↵Axel Lin2012-06-051-18/+2
| | | | | | | | | | | VDCDCx The voltage mapping table for LDO2 is exactly the same as VDCDCx. Thus we can use one mapping table for both LDO2 and VDCDCx instead of duplicating the mapping table. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps6507x: Remove unused min_uV and max_uV from struct tps_infoAxel Lin2012-06-051-12/+0
| | | | | | | | | | The min_uV and max_uV are not used in this driver. For table based voltage mappings, we can get min_uV and max_uV by info->table[0] and info->table[table_len -1]. Thus remove min_uV and max_uV from struct tps_info. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps6507x: Use regulator_list_voltage_table()Axel Lin2012-06-031-57/+43
| | | | | Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: Remove unneeded include of linux/delay.h from regulator driversAxel Lin2012-04-231-1/+0
| | | | | | | | | | | | | All the drivers that need delay for the regulator voltage output voltage to stabilize after being enabled or after being set to a new value has been converted to implement enable_time and set_voltage_time_sel callbacks. Then regulator core will take care of the necessary delay. For the drivers that don't need the delay, don't need to include linux/delay.h. This patch removes the unneeded include of linux/delay.h in regulator drivers. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps6507x: Convert to get_voltage_selAxel Lin2012-04-201-3/+3
| | | | | Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: Convert tps65xxx regulator drivers to use devm_kzallocAxel Lin2012-04-111-6/+1
| | | | | Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: core: Use a struct to pass in regulator runtime configurationMark Brown2012-04-091-2/+6
| | | | | | | | | | | | | | Rather than adding new arguments to regulator_register() every time we want to add a new bit of dynamic information at runtime change the function to take these via a struct. By doing this we avoid needing to do further changes like the recent addition of device tree support which required each regulator driver to be updated to take an additional parameter. The regulator_desc which should (mostly) be static data is still passed separately as most drivers are able to configure this statically at build time. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: Convert tps6507x to set_voltage_selAxel Lin2012-03-141-26/+5
| | | | | Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: Refactor tps6507x to use one tps6507x_pmic_ops for all LDOs and DCDCsAxel Lin2012-03-141-201/+67
| | | | | | | | | All the callback functions implementation for DCDCx and LDOx are very similar, I think it is ok to use one tps6507x_pmic_ops for all LDOs and DCDCs. This refactor removes a couple of duplicated code. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: pass additional of_node to regulator_register()Rajendra Nayak2011-11-231-1/+1
| | | | | | | | | | | With device tree support for regulators, its needed that the regulator_dev->dev device has the right of_node attached. To be able to do this add an additional parameter to the regulator_register() api, wherein the dt-adapted driver can then pass this additional info onto the regulator core. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps6507x: Remove num_voltages arrayAxel Lin2011-08-081-7/+1
| | | | | | | | We can get n_voltages for each regulator from table_len of struct tps_info. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Fix desc_id for tps65023/6507x/65910Axel Lin2011-05-271-2/+1
| | | | | | | | | | | | | | The desc_id variable should not be a static variable. The rest of the code assumes the desc_id must less than TPSxxxxx_NUM_REGULATOR. If we set desc_id to be a static variable, checking the return value of rdev_get_id() may return error. Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: Anuj Aggarwal <anuj.aggarwal@ti.com> Cc: Graeme Gregory <gg@slimlogic.co.uk> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Report actual configured voltage to set_voltage()Mark Brown2011-01-121-2/+8
| | | | | | | | | | | Change the interface used by set_voltage() to report the selected value to the regulator core in terms of a selector used by list_voltage(). This allows the regulator core to know the voltage that was chosen without having to do an explict get_voltage(), which would be much more expensive as it will generally access hardware. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: tps6507x - remove incorrect commentsAxel Lin2010-09-011-6/+0
| | | | | | | | | This driver is a platform driver, not a i2c driver. Thus remove incorrect tps6507x_remove comments. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: tps6507x - add missing platform_set_drvdata in tps6507x_pmic_probeAxel Lin2010-08-111-0/+1
| | | | | | | | We should call platform_set_drvdata() before calling platform_get_drvdata(). Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH registerAnuj Aggarwal2010-07-281-7/+29
| | | | | | | | | | | | | | | | | | | | Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> In TPS6507x, depending on the status of DEFDCDC{2,3} pin either DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or programmed to change the output voltage. The current driver assumes DEFDCDC{2,3} pins are always tied low and thus operates only on DEFDCDC{2,3}_LOW register. This need not always be the case (as is found on OMAP-L138 EVM). Unfortunately, software cannot read the status of DEFDCDC{2,3} pins. So, this information is passed through platform data depending on how the board is wired. Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* mfd: Add TPS6507x supportTodd Fischer2010-05-281-79/+74
| | | | | | | | | | | TPS6507x are multi function (PM, touchscreen) chipsets from TI. This commit also changes the corresponding regulator driver from being standalone to an MFD subdevice. Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* regulator: tps6057x namespace cleanupTodd Fischer2010-05-281-85/+87
| | | | | | | | | Move from using tps or tsp6507x to tps6057x_pmic in a consistent manner. Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Add tps6507x board data structureTodd Fischer2010-05-281-2/+12
| | | | | | | | | | | | Add mfd structure which refrences sub-driver initialization data. For example, for a giving hardware implementation, the voltage regulator sub-driver initialization data provides the mapping betten a voltage regulator and what the output voltage is being used for. Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* mfd: Move TPS6507x register definition to header file.Todd Fischer2010-05-281-59/+1
| | | | | | | | | | Other sub-drivers for the TPS6507x chip will need to use register definition so move it out of the source file and into a header file. Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo2010-03-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* Regulators: tps6507x-regulator - mark probe method as __devinitDmitry Torokhov2010-03-031-19/+15
| | | | | | | | | Also move error handling in probe() out of line and do not bother to reset fields in structures that are about to be freed. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: tps650xx - build fixes for x86_64Liam Girdwood2009-09-221-5/+6
| | | | | | | | | | | | Fixes the following errors on both tps650xx regulator drivers :- drivers/regulator/tps65023-regulator: struct i2c_device_id is 32 bytes. The last of 1 is: 0x74 0x70 0x73 0x36 0x35 0x30 0x32 0x33 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 FATAL: drivers/regulator/tps65023-regulator: struct i2c_device_id is not terminated with a NULL entry! This patch also fixes the GPL v2 licence string for both drivers. Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* Regulator: Add TPS6507x regulator driverAnuj Aggarwal2009-09-221-0/+713
Adding support for TI TPS6507x regulator driver Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
OpenPOWER on IntegriCloud