| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Upgrade nomadik pinctrl driver to enable selection of other
alternate-C[1-4] functions on some specific ux500 SoC pins.
Handling of those functions is done thanks to PRCM GPIOCR
registers. This was previously managed in PRCMU driver and
it was not really convenient. Idea is to provide a common
way to control all alternate functions.
Note that this improvement does not support the old-fashioned way
used to control nomadik pins, namely the "nmk_config_pin()" function
and its derivatives.
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
| |
Another possible pin configuration for the MC1 pin group.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
|
| |
There is yet another way to mux the keyboard, so fix up that
group.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
| |
Tidy up a small typo in the HSI function group list.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
|
|
| |
On 8500 and 9540, all SPI2 pins are driven by SPI block except SPI2_FRM
which is driven as GPIO due to specific constraints.
A new group spi2_oc1_2 is created which exclude SPI2_FRM pin.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
| |
mc0_dat47_a_1 and mc0dat31dir_a_1 groups are missing for mco function
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
|
|
|
| |
On 8500 and 9540, all HSI pins are driven by HSI block except
HSIT_ACWAKE0_a which is driven as GPIO due to specific
constraints. A new group hsit_a_2 is created which exclude
HSIT_ACWAKE0_a pin.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
|
| |
Add smcs1_b_1_pins as DB8500_PIN_B14 can be SM_CS1 in alt B
Add smps0_c_1_pins as DB8500_PIN_E8 can be SM_PS0 in alt C
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
| |
move DB8500_PIN_AJ11(HSIR_RDY0_a) from hsit_a_1_pins to hsir_a_1_pins
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Implements basic pinmux for the Nomadik pin controller.
The plan is to split the existing singular pin config interface
nmk_config_pin(), nmk_config_pins(), that will configure muxing
and other settings at the same time, into two interfaces
by splitting the code in pinmux and pinctrl and eventually
deleting the old interface and its helper functions when all
users are gone.
nmk_gpio_set_mode() and nmk_gpio_get_mode() are two older
interfaces for just configuring muxing/altfunctions that
will also be replaced in the end.
We take some extra care to handle the glitch-avoidance here,
but it is simpler now since there is only one altsetting per
pingroup so we know immediately if we need to avoid altfunc
C glitches for a certain group.
As part of the makeover implement the .request() and .free()
calls on the GPIO chips and have them call back into the
pinctrl layer to reserve GPIOs.
ChangeLog v1->v2:
- Rebased on pinctrl-mergebase-20120418 so we get the latest
driver infrastructure where function count is done by a fixed
value and we can drop a few range checks since this is now
handled by the core.
- Include a GPIO muxing hunk erroneously part of the pin config
patch.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a scratch pin control interface to the Nomadik pinctrl
driver, and defines the pins and groups in the DB8500 ASIC. We
define GPIO ranges to cover the pins exposed. The DB8500 has
more pins than this but we restrict the driver to the pins that
can be controlled from the combined GPIO and pin control hardware
to begin with.
ChangeLog v1->v2:
- Base on the latest pinctrl development from
pinctrl-mergebase-20120418 so we can get rid of legacy
group count mechanism. Also drop the range checks for group
index, this is handled by the core now.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|