summaryrefslogtreecommitdiffstats
path: root/drivers/net/sfc/sfe4001.c
Commit message (Collapse)AuthorAgeFilesLines
* sfc: Add support for SFN4111TBen Hutchings2008-12-121-31/+122
| | | | | | | | Add support code for the SFN4111T 100/1000/10GBASE-T reference design, based in part on the existing code for the SFE4001. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for sub-10G speedsBen Hutchings2008-12-121-1/+1
| | | | | | | | | | | | | The SFC4000 has a separate MAC for use at sub-10G speeds. Introduce an efx_mac_operations structure with implementations for the two MACs. Switch between the MACs as necessary. PHY settings are independent of the MAC, so add get_settings() and set_settings() to efx_phy_operations. Also add macs field to indicate which MACs the PHY is connected to. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Use lm87 and lm90 drivers for board temperature/power monitoringBen Hutchings2008-11-061-63/+53
| | | | | | | | | Add board monitoring to periodic work whenever link is down. For SFE4001, report when a fault has caused the PHY to turn off. For SFE4002, switch XFP PHY into low-power state in case of a fault. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sfc: Remove workaround for old firmware bugBen Hutchings2008-09-241-12/+0
| | | | | | | | | There was a bug in XAUI synchronisation in early 10Xpress firmware versions. This is fixed in released firmware and we do not need to work around it. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sfc: Remove remnants of multi-port abstraction for MAC registersBen Hutchings2008-09-031-3/+4
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sfc: Make PHY flash mode a device attribute, not a module parameterBen Hutchings2008-09-031-68/+118
| | | | | | | | | | | | | This allows updating PHY firmware for one interface without removing all other interfaces handled by the driver. Replace tx_disabled flags and 10Xpress status enumeration with flags in enum efx_phy_mode. Prevent an interface from being brought up while in PHY flash mode. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sfc: Reduce delays in SFE4001 initialisationBen Hutchings2008-09-031-22/+35
| | | | | | | | | | Currently the board initialisation includes 2 delays of 1 second each. Usually it is unnecessary to wait that long, so check before doing so. Correct some of the comments and log messages while we're here. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sfc: Use kernel I2C system and i2c-algo-bit driverBen Hutchings2008-05-301-60/+66
| | | | | | | Remove our own implementation of I2C bit-banging. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sfc: Removed casts to voidBen Hutchings2008-05-221-7/+7
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [netdrvr] sfc: Add phy_flash_cfg module parameter and implementationBen Hutchings2008-05-131-0/+14
| | | | | | | | | The 10Xpress PHY supports flash upgrades through MDIO, but needs to be put in upgrade mode at power-up. This adds a module parameter and other logic to support that. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* New driver "sfc" for Solarstorm SFC4000 controller.Ben Hutchings2008-04-291-0/+252
The driver supports the 10Xpress PHY and XFP modules on our reference designs SFE4001 and SFE4002 and the SMC models SMC10GPCIe-XFP and SMC10GPCIe-10BT. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
OpenPOWER on IntegriCloud