summaryrefslogtreecommitdiffstats
path: root/drivers/net/s2io-regs.h
Commit message (Collapse)AuthorAgeFilesLines
* [PATCH] S2io: Offline diagnostics fixesravinandan.arakali@neterion.com2005-10-181-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes the following bugs with offline diagnostics code(run with "ethtool -t"). 1. After running offline diagnostics, adapter would report corrupted packets on receive. This was because of adapter not being brought out of "RLDRAM test mode". 2. Current EEPROM test works only for Xframe I. Since Xframe II uses different interface(SPI), support for this interface has been added. Also, since SPI supports write access to all areas of EEPROM, negative testing is done only for Xframe I. 3. Return values from subfunctions of offline diagnostics have been corrected. 4. In register test, expected value from rx_queue_cfg register is made to depend on adapter type. 5. After the test, need to restore values at EEPROM offsets 0x4F0 and 0x7F0. These locations were modified as part of test. 6. Use macro SPECIAL_REG_WRITE for write access to mc_rldram_test_ctrl register. Also, couple of unnecessary writes to mc_rldram_test_ctrl have been removed. Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* [PATCH] S2io: Hardware and miscellaneous fixesravinandan.arakali@neterion.com2005-09-061-5/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | Hi, This patch contains the following hardware related fixes and other miscellaneous bug fixes. 1. Updated the definition of single and double-bit ECC errors 2. Earlier we were allocating Transmit descriptors equal to MAX_SKB_FRAGS. This was causing a boundary condition failure. Need to allocate MAX_SKB_FRAGS+1 descriptors. 3. On some platforms(like PPC), pci_alloc_consistent() can return a zero DMA address. Since the NIC cannot handle zero-addresses, a workaround has been provided. Basically, we don't use such that page. We reallocate. 4. If list_info allocation failed during driver load, check for it during driver exit and return instead of trying to dereference NULL pointer. 5. Increase the debug level of few non-critical debug messages. 6. Reset the card on critical ECC double errors only in case of XframeI since XframeII can recover from such errors. 7. Print copyright message on driver load. 8. Bumped up the driver version no. to 2.0.8.1 Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* [PATCH] S2io: New link handling scheme for Xframe IIraghavendra.koushik@neterion.com2005-08-111-1/+7
| | | | | | | | | | | Hi, The below patch implements a new "Link state change handling" scheme supported by the Xframe II adapter. It also bumps up the driver version to 2.0.2.0. Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com> Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* [PATCH] S2io: Support for Xframe II NICraghavendra.koushik@neterion.com2005-08-111-12/+41
| | | | | | | | | | | | | | | | | | | Hi, This patch provides basic support for the Xframe II adapter. Includes the following changes: 1. New values to program XAUI interface. 2. Print the PCI/PCI-X mode(bus frequency, width). 3. Remove EOI from reset during intialization. 4. Enable all 8 PCCs if Xframe II adapter. 5. Programs the RLDRAM size depending on the device. (Note: RLDRAM size on XFARME-I is 64Mb whereas on XFRAME-II it's 32 Mb). 6. Enable extended(64-bit) statistics counters. 7. Program timer interrupt duration based on PCI/PCI-X clock speed. 8. Not required to save/restore PCI config space before/after reset. Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com> Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* [PATCH] S2io: Hardware fixesraghavendra.koushik@neterion.com2005-08-111-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | Hi, Below patch addresses few h/w specific issues. 1. Check for additional ownership bit on Rx path before starting Rx processing. 2. Enable only 4 PCCs(Per Context Controller) for Xframe I revisions less than 4. 3. Program Rx and Tx round robin registers depending on no. of rings/FIFOs. 4. Tx continous interrupts is now a loadable parameter. 5. Reset the card if we get double-bit ECC errors. 6. A soft reset of XGXS being done to force a link state change has been eliminated. 7. After a reset, clear "parity error detected" bit, PCI-X ECC status register, and PCI_STATUS bit in tx_pic_int register. 8. The error in the disabling allmulticast implementation has been rectified. 9. Leave the PCI-X parameters MMRBC, OST etc. at their BIOS/system defaults. Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com> Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* [PATCH] S2io: Code cleanupraghavendra.koushik@neterion.com2005-08-111-10/+9
| | | | | | | | | | | | | | | | | | | | | | | Hi, We are submitting a series of 13 patches to support our Xframe I and Xframe II line of products. The patches can be categorized as follows: Patches 1-8 : Changes applicable to both Xframe I and II Patches 9-11: Xframe II specific features Patch 12: Addresses issues found during testing cycle. Patch 13: Incorpoates mostly the review comments from community and some last moment bug fixes. Please review the patches and let us know your comments. Starting with patch 1 below. This patch involves cosmetic changes(tabs and indentation, regrouping of transmit and receive data structures, typecasting, code cleanup). Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com> Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* Linux-2.6.12-rc2v2.6.12-rc2Linus Torvalds2005-04-161-0/+778
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
OpenPOWER on IntegriCloud