summaryrefslogtreecommitdiffstats
path: root/drivers/net/qlcnic
Commit message (Collapse)AuthorAgeFilesLines
* qlcnic: add loopback diagnostic testAmit Kumar Salecha2010-02-025-10/+225
| | | | | | | | | | | | Loopback test (offline) added in ethtool self test. o Set device in loopback mode o Send packets o Process receive packets in qlcnic_process_rcv_ring_diag() o Compare packets o Reset device in normal mode. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlcnic: add interrupt diagnostic testAmit Kumar Salecha2010-02-024-16/+154
| | | | | | | | | | Interrupt test (offline) added in ethtool self test. Register a temporary interrupt handler and then send command to fw to raise an interrupt. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlcnic: support LED blink for device identificationSucheta Chakraborty2010-02-023-0/+49
| | | | | | | | Added support of device identification by blinking LED for specified time. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlcnic: protect resoruce cleanup by rtnl lockAmit Kumar Salecha2010-02-022-3/+5
| | | | | | | | | | | | o context resources can be in used, while resoruce cleanup is in progress, during fw recover. o Null pointer execption can occur in send_cmd_desc, if fw recovery module frees tx ring without rtnl lock. o Same applies to ethtool register dump and FW health registers should be dump in any case. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlcnic: clear device reset state after fw recoveryAmit Kumar Salecha2010-02-021-1/+21
| | | | | | | | o After firmware recovery, clear device reset state transition register. Otherwise firmware reload can occur unnecessary. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlcnic: add ethernet identifier in board infoAmit Kumar Salecha2010-02-021-3/+7
| | | | | | | | | Added missing identifier that distinguishes between FCOE/ISCSI/ETHERNET functions. Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlcnic: use DEFINE_PCI_DEVICE_TABLEAmit Kumar Salecha2010-02-021-1/+1
| | | | | | | | Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section in every case. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlcnic: Qlogic ethernet driver for CNA devicesAmit Kumar Salecha2010-01-168-0/+8728
o 1G/10G Ethernet Driver for Qlgic QLE8240 and QLE8242 CNA devices. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
OpenPOWER on IntegriCloud