summaryrefslogtreecommitdiffstats
path: root/drivers/net/ixgbe
Commit message (Collapse)AuthorAgeFilesLines
* tree-wide: fix comment/printk typosUwe Kleine-König2010-11-011-2/+2
| | | | | | | | | | "gadget", "through", "command", "maintain", "maintain", "controller", "address", "between", "initiali[zs]e", "instead", "function", "select", "already", "equal", "access", "management", "hierarchy", "registration", "interest", "relative", "memory", "offset", "already", Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* ixgbe: DCB, fix TX hang occurring in stress condition with PFCJohn Fastabend2010-10-285-10/+54
| | | | | | | | | | | | | | | | The DCB credits refill quantum _must_ be greater than half the max packet size. This is needed to guarantee that TX DMA operations are not attempted during a pause state. Additionally, the min IFG must be set correctly for DCB mode. If a DMA operation is requested unexpectedly during the pause state the HW data store may be corrupted leading to a DMA hang. The DMA hang requires a reset to correct. This fixes the HW configuration to avoid this condition. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: add a refcnt when turning on/off FCoE offload capabilityYi Zou2010-10-212-0/+7
| | | | | | | | | | | | | | | The FCoE offload is enabled/disabled per adapter, but upper FCoE protocol stack could have multiple FCoE instances created on the same physical network interface, e.g., FCoE on multiple VLAN interfaces on the same physical network interface. In this case we want to turn on FCoE offload at the first request from ndo_fcoe_enable() but only turn off FCoE offload at the very last call to ndo_fcoe_disable(). This is fixed by adding a refcnt in the per adapter FCoE structure and tear down FCoE offload when refcnt decrements to zero. Signed-off-by: Yi Zou <yi.zou@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: fix stats handlingEric Dumazet2010-10-213-16/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | Current ixgbe stats have following problems : - Not 64 bit safe (on 32bit arches) - Not safe in ixgbe_clean_rx_irq() : All cpus dirty a common location (netdev->stats.rx_bytes & netdev->stats.rx_packets) without proper synchronization. This slow down a bit multiqueue operations, and possibly miss some updates. Fixes : Implement ndo_get_stats64() method to provide accurate 64bit rx|tx bytes/packets counters, using 64bit safe infrastructure. ixgbe_get_ethtool_stats() also use this infrastructure to provide 64bit safe counters. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: update copyright infoEmil Tantilov2010-10-214-4/+4
| | | | | | | | Update copyright notice Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: Update ixgbe to use new vlan accleration.Jesse Gross2010-10-213-79/+74
| | | | | | | | | | Make the ixgbe driver use the new vlan accleration model. Signed-off-by: Jesse Gross <jesse@nicira.com> CC: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com> CC: Emil Tantilov <emil.s.tantilov@intel.com> CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vlan: Don't check for vlan group before vlan_tx_tag_present.Jesse Gross2010-10-211-1/+1
| | | | | | | | | | | | | Many (but not all) drivers check to see whether there is a vlan group configured before using a tag stored in the skb. There's not much point in this check since it just throws away data that should only be present in the expected circumstances. However, it will soon be legal and expected to get a vlan tag when no vlan group is configured, so remove this check from all drivers to avoid dropping the tags. Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vlan: Rename VLAN_GROUP_ARRAY_LEN to VLAN_N_VID.Jesse Gross2010-10-211-1/+1
| | | | | | | | | | VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs. Since vlan groups will soon be more of an implementation detail for vlan devices, rename the constant to be descriptive of its actual purpose. Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: DCB: remove DCB check configJohn Fastabend2010-10-151-1/+0
| | | | | | | | | | | | | | | Remove a DCB check config from DCB configuration we continue to configure DCB even if it fails so don't even bother to check. Plus user space (lldpad) checks this before programming the hw anyways. Worse case is we program some values into the hw that don't make total sense resulting in incorrect bandwidth allocation. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: declare functions as staticEmil Tantilov2010-10-1411-86/+40
| | | | | | | | | | | | Following patch fixes warnings reported by `make namespacecheck` Reported by Stephen Hemminger CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: remove unused functionsEmil Tantilov2010-10-148-555/+0
| | | | | | | | | | | | | Remove functions that are declared, but not used in the driver. This patch fixes warnings reported by `make namespacecheck` Reported by Stephen Hemminger CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: Use affinity_hint when Flow Director is enabledPeter Waskiewicz2010-10-062-0/+27
| | | | | | | | | | Use the new infrastructure to balance interrupts for flow alignment when ATR or Flow Director are enabled. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: fix link issues and panic with shared interrupts for 82598Emil Tantilov2010-09-301-10/+26
| | | | | | | | | | | | | | | Fix possible panic/hang with shared Legacy interrupts by not enabling interrupts when interface is down. Also fixes an intermittent link by enabling LSC upon exit from ixgbe_intr() This patch adds flags to ixgbe_irq_enable() to allow for some flexibility when enabling interrupts. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: Use netif_set_real_num_{rx,tx}_queues()Ben Hutchings2010-09-271-5/+11
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: return operator cleanupEric Dumazet2010-09-262-4/+4
| | | | | | | | | Change "return (EXPR);" to "return EXPR;" return is not a function, parentheses are not required. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000/e1000e/igb/ixgb/ixgbe: set NETIF_F_HIGHDMA for VLAN feature flagsYi Zou2010-09-221-1/+3
| | | | | | | | | | | | | | | If the netdev->features is set with NETIF_F_HIGHDMA, we should set the corresponding netdev->vlan_features as well to allow VLAN netdev created on top of the real netdev to be able to also benefit from HIGHDMA on 32bit system, reducing the performance hit that is caused by __skb_linearize(), particularly for large send. This is fixed in this patch for all Intel e1000, e1000e, igb, ixgbe, and ixgbe drivers since this should be beneficial to all devices supported by these drivers. Signed-off-by: Yi Zou <yi.zou@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethtool, ixgbe: Move RX n-tuple mask fixup to ethtoolBen Hutchings2010-09-171-43/+14
| | | | | | | | | | | The ethtool utility does not set masks for flow parameters that are not specified, so if both value and mask are 0 then this must be treated as equivalent to a mask with all bits set. Currently that is done in the only driver that implements RX n-tuple filtering, ixgbe. Move it to the ethtool core. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/ixgbe/ixgbe_main.c: Add ixgbe_psumJoe Perches2010-09-081-146/+151
| | | | | | | | | | Reduce indentation in a couple of places Add static function ixgbe_psum Add temporary for adapter->stats Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/ixgbe/ixgbe_main.c: Use pr_<level>Joe Perches2010-09-081-38/+36
| | | | | | | | | Did not add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt because no printk in this module used message prefixing. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/ixgbe/ixgbe_main.c: Checkpatch cleanupsJoe Perches2010-09-081-231/+236
| | | | | | | | | Whitespace cleanups. Move inline keyword after function type declarations. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: fix TX ring enable issues seen when VMDQ is enabledAlexander Duyck2010-09-081-1/+1
| | | | | | | | | | | The ordering of operations was messed up in the init and as a result when VMDQ was enabled we were trying to enable TX rings before setting the VFTE bits. This resulted in a ring that appeared to fail to enable when in fact it was blocked because the VFTE bits were cleared after the reset. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: avoid some skb->ip_summed initializationsEric Dumazet2010-09-022-3/+4
| | | | | | | | | | | | | | | | | | | | fresh skbs have ip_summed set to CHECKSUM_NONE (0) We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers. Introduce skb_checksum_none_assert() helper so that we keep this assertion documented in driver sources. Change most occurrences of : skb->ip_summed = CHECKSUM_NONE; by : skb_checksum_none_assert(skb); Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: Remove address use from assignments of function pointersJoe Perches2010-08-251-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | "foo = &function" is more commonly written "foo = function" Done with coccinelle script: // <smpl> @r@ identifier f; @@ f(...) { ... } @@ identifier r.f; @@ - &f + f // </smpl> drivers/net/tehuti.c used a function and struct with the same name, the function was renamed. Compile tested x86 only. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: rewrite ethtool test to use standard config functionsAlexander Duyck2010-08-193-253/+169
| | | | | | | | | | This change makes it so that the ethtool loopback test uses the standard ring configuration and allocation functions. As a result the loopback test will be much more effective at testing core driver functionality. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: update all DESC_ADV macros to accept a ring pointerAlexander Duyck2010-08-194-18/+18
| | | | | | | | | | | All of the DESC_ADV macros are currently needing the pointers to be de-referenced before accessing the ring. Instead of having to add all of the asterisks it is easier to just update the macro to expect a pointer to the ring. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: combine Rx into into ixgbe_configure_rxAlexander Duyck2010-08-191-57/+95
| | | | | | | | | | The Rx init is currently split over ixgbe_configure, ixgbe_configure_rx, and ixgbe_up_complete. Instead of leaving it split over 3 function it is easier to consolidate them all into ixgbe_configure_rx. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: pull all Tx init into ixgbe_configure_txAlexander Duyck2010-08-191-39/+52
| | | | | | | | | | The Tx init was spread out over ixgbe_configure, ixgbe_configure_tx, and ixgbe_up_complete. This change combines all of that into the ixgbe_configure_tx function in order to simplify the Tx init path. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: move all GPIE register config into a single functionAlexander Duyck2010-08-191-42/+30
| | | | | | | | | | This change moves all GPIE register configuration into a single function. The advantage of this is that we can avoid a number of unnecessary read/modify/write cycles on the register. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: Move virtualization config into a separate functionAlexander Duyck2010-08-191-38/+46
| | | | | | | | | This change moves the configuration that was done in configure_rx into a separate virtualization configuration function. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: move all Rx DMA control register writes to one central locationAlexander Duyck2010-08-192-43/+50
| | | | | | | | | | This change moves all of the Rx DMA control register writes to one central location. This should help to avoid accidentally overwriting existing settings. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: Move max frame size and Rx buffer length configuration into a functionAlexander Duyck2010-08-191-48/+60
| | | | | | | | | This change consolidates all of the Rx max frame size and Rx buffer length configuration into a single function. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: remove redundant configuration of vmolr, rename generic variableAlexander Duyck2010-08-191-7/+4
| | | | | | | | | | | | The vmolr is configured already in ixgbe_set_rx_mode for the PF so there is no need to set it again in ixgbe_configure_rx. Instead of using the variable name reg, it is easier to just rename it to gcr_ext to reflect the register contents that the variable holds. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: bump PS header size to 512 bytesAlexander Duyck2010-08-191-4/+9
| | | | | | | | | | Bump the header size for packet split to 512 bytes since this makes the best use of the 1k buffer that is allocated for any skb 512 bytes or smaller. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: combine accesses to FCTRL register into ixgbe_set_rx_modeAlexander Duyck2010-08-191-7/+6
| | | | | | | | | | We are accessing the FCTRL register in multiple spots in the init path and we can simplify things by combining the configuration all into ixgbe_set_rx_mode. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: pull PSRTYPE configuration into a separate functionAlexander Duyck2010-08-191-11/+25
| | | | | | | | | | The configuration of PSRTYPE was being done conditionally on if packet split is enabled or not. It can be configured always since it will not have any effect when packet split is not enabled. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: pull ring configuration into it's own functionAlexander Duyck2010-08-191-13/+20
| | | | | | | | | These changes add ixgbe_configure_rx_ring which is used to setup the base function pointers for the ring. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: consolidate all setting of MRQC into one functionAlexander Duyck2010-08-191-57/+43
| | | | | | | | | | | | | This change simplifies the configuration of MRQC by consolidating the setting of it into one function. As such the register is no longer set in multiple places which should make any future changes easier to work with. In addition we can combine RSS related register writes into the call since enabling all of those bits without enabling RSS itself in MRQC should have no effect. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: move Tx ring configuration into a separate functionAlexander Duyck2010-08-191-40/+29
| | | | | | | | | | This patch moves the Tx ring configuration into a separate function. In addition the function drops the setting of the head writeback RO bit since head writeback is no longer used within ixgbe. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: move configuration of the MTQC register into it's own functionAlexander Duyck2010-08-191-33/+40
| | | | | | | | | This patch moves the configuration of the MTQC register into it's own function call similar to ixgbe_setup_mrqc. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: combine two modifications of TXDCTL into oneAlexander Duyck2010-08-191-12/+6
| | | | | | | | | | | In ixgbe_up_complete we were doing a read-modify-write of TXDCTL followed by another one just a few lines further down. Instead of performing two separate read-modify-writes it would make more sense to combine the two into one. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: move setting of GSO size for 82598 into ixgbe_configure_dcbAlexander Duyck2010-08-191-11/+10
| | | | | | | | | | We are unnecessarily modifying the GSO size for all HW when we don't need to. The code can be simplified by moving the check for DCB and the adjustment of the GSO size for 82598 into ixgbe_configure_dcb. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: remove redundant DMA alignment codeAlexander Duyck2010-08-191-12/+12
| | | | | | | | | | | | | This patch removes the redundant DMA alignment code from the Rx buffer allocation path. This code is no longer necessary since all x86 buffers are now DMA aligned due to recent changes to NET_IP_ALIGN and NET_SKB_PAD. It also moves the setting of the Rx queue value into the allocation path since it is more likely that the queue mapping will still be in the cache at the time of allocation. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: cleanup ixgbe_get_drvinfo to be extra careful with buffer boundariesDon Skidmore2010-08-191-10/+13
| | | | | | | | | Make the code in ixgbe_get_drvinfo more protected against buffer overflow boundaries by using snprintf and sizeof with snprintf. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e100/e1000*/igb*/ixgb*: Add missing read memory barrierJeff Kirsher2010-08-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on patches from Sonny Rao and Milton Miller... Combined the patches to fix up clean_tx_irq and clean_rx_irq. The PowerPC architecture does not require loads to independent bytes to be ordered without adding an explicit barrier. In ixgbe_clean_rx_irq we load the status bit then load the packet data. With packet split disabled if these loads go out of order we get a stale packet, but we will notice the bad sequence numbers and drop it. The problem occurs with packet split enabled where the TCP/IP header and data are in different descriptors. If the reads go out of order we may have data that doesn't match the TCP/IP header. Since we use hardware checksumming this bad data is never verified and it makes it all the way to the application. This bug was found during stress testing and adding this barrier has been shown to fix it. The bug can manifest as a data integrity issue (bad payload data) or as a BUG in skb_pull(). This was a nasty bug to hunt down, if people agree with the fix I think it's a candidate for stable. Previously Submitted to e1000-devel only for ixgbe http://marc.info/?l=e1000-devel&m=126593062701537&w=3 We've now seen this problem hit with other device drivers (e1000e mostly) So I'm resubmitting with fixes for other Intel Device Drivers with similar issues. CC: Milton Miller <miltonm@bga.com> CC: Anton Blanchard <anton@samba.org> CC: Sonny Rao <sonnyrao@us.ibm.com> CC: stable <stable@kernel.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIGJohn Fastabend2010-08-081-4/+10
| | | | | | | | | | | | | | | | | | Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause a build error. This resolves the build error by wrapping the fcoe.up in CONFIG_IXGBE_DCB ifdefs. Also frames were being priority VLAN tagged even without DCB enabled. This fixes this so that 8021Q priority tags are only added with DCB actually enabled. Reported-by: divya <dipraksh@linux.vnet.ibm.com> Reported-by: Jon Mason <jon.mason@exar.com> Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2010-07-271-0/+9
|\ | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/bnx2x_main.c Merge bnx2x bug fixes in by hand... :-/ Signed-off-by: David S. Miller <davem@davemloft.net>
| * ixgbe/igb: catch invalid VF settingsAndy Gospodarek2010-07-211-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some ixgbe cards put an invalid VF device ID in the PCIe SR-IOV capability. The ixgbe driver is only valid for PFs or non SR-IOV hardware. It seems that the same problem could occur on igb hardware as well, so if we discover we are trying to initialize a VF in ixbge_probe or igb_probe, print an error and exit. Based on a patch for ixgbe from Chris Wright <chrisw@sous-sol.org>. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Cc: Chris Wright <chrisw@sous-sol.org> Acked-by: Chris Wright <chrisw@sous-sol.org> Acked-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ixgbe: potential null dereferenceDan Carpenter2010-07-271-3/+4
| | | | | | | | | | | | | | | | The e_dev_err() macro dereferences "adapter" which is NULL here. Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ixgbe: priority tagging FCoE frames without FCoE offloadJohn Fastabend2010-07-271-21/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | The DCB user priority for FCoE is available regardless of whether FCoE offload is enabled (IXGBE_FLAG_FCOE_ENABLED bit is set). This allows proper DCB user priority tagging for FCoE traffic on both 82598 and 82599 devices. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ixgbe: fix ethtool statsEric Dumazet2010-07-241-21/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In latest changes about 64bit stats on 32bit arches, [commit 28172739f0a276eb8 (net: fix 64 bit counters on 32 bit arches)], I missed ixgbe uses a bit of magic in its ixgbe_gstrings_stats definition. IXGBE_NETDEV_STAT() must now assume offsets relative to rtnl_link_stats64, not relative do dev->stats. As a bonus, we also get 64bit stats on ethtool -S Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
OpenPOWER on IntegriCloud