| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
| |
Like the STi and sunxi series SOCs, Altera's SOCFPGA also needs a glue layer
on top of the Synopsys gmac IP.
This patch adds the platform driver for the glue layer which configures the IP
before the generic STMMAC driver takes over.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
Replace dev_kfree_skb with dev_consume_skb_any in stmmac_tx_clean that can
be called in hard irq and other contexts. stmmac_tx_clean handles
freeing successfully transmitted packets.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
|
|
|
|
|
|
|
|
|
| |
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
This is to fix the compatibility to the STiD127 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
This patch is to fix the chain mode that was broken
and generated a panic. This patch reviews the chain/ring
modes now shaing the same structure and taking care
about the pointers and callbacks.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
This patch is to fix and tune the default buffer sizes.
It reduces the default bufsize used by the driver from
4KiB to 1536 bytes.
Patch has been tested on both ARM and SH4 platform based.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
This patch is to disable the EEE (so HW and timers)
for example when the phy communicates that the EEE
can be supported anymore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
alloc_dma_desc_resources() returns an error value and the next line
actually checks for it, so assign the return value properly.
Found by the coverity scanner.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.
This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
Logging the MAC address on every if-up, is not really useful, and annoying when
there is no cable inserted and NetworkManager tries the ifup every 50 seconds.
Also change the log level from warning to info, as that is what it is.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
Logging a PTP error on hw which simply does not support PTP is not very
useful. Moreover this message gets logged on every if-up, and if there is
no cable inserted NetworkManager will re-try the ifup every 50 seconds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
These changes correct the following issues with jumbo frames on the
stmmac driver:
1) The Synopsys EMAC can be configured to support different FIFO
sizes at core configuration time. There's no way to query the
controller and know the FIFO size, so the driver needs to get this
information from the device tree in order to know how to correctly
handle MTU changes and setting up dma buffers. The default
max-frame-size is as currently used, which is the size of a jumbo
frame.
2) The driver was enabling Jumbo frames by default, but was not allocating
dma buffers of sufficient size to handle the maximum possible packet
size that could be received. This led to memory corruption since DMAs were
occurring beyond the extent of the allocated receive buffers for certain types
of network traffic.
kernel BUG at net/core/skbuff.c:126!
Internal error: Oops - BUG: 0 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 563 Comm: sockperf Not tainted 3.13.0-rc6-01523-gf7111b9 #31
task: ef35e580 ti: ef252000 task.ti: ef252000
PC is at skb_panic+0x60/0x64
LR is at skb_panic+0x60/0x64
pc : [<c03c7c3c>] lr : [<c03c7c3c>] psr: 60000113
sp : ef253c18 ip : 60000113 fp : 00000000
r10: ef3a5400 r9 : 00000ebc r8 : ef3a546c
r7 : ee59f000 r6 : ee59f084 r5 : ee59ff40 r4 : ee59f140
r3 : 000003e2 r2 : 00000007 r1 : c0b9c420 r0 : 0000007d
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 2e8ac04a DAC: 00000015
Process sockperf (pid: 563, stack limit = 0xef252248)
Stack: (0xef253c18 to 0xef254000)
3c00: 00000ebc ee59f000
3c20: ee59f084 ee59ff40 ee59f140 c04a9cd8 ee8c50c0 00000ebc ee59ff40 00000000
3c40: ee59f140 c02d0ef0 00000056 ef1eda80 ee8c50c0 00000ebc 22bbef29 c0318f8c
3c60: 00000056 ef3a547c ffe2c716 c02c9c90 c0ba1298 ef3a5838 ef3a5838 ef3a5400
3c80: 000020c0 ee573840 000055cb ef3f2050 c053f0e0 c0319214 22b9b085 22d92813
3ca0: 00001c80 004b8e00 ef3a5400 ee573840 ef3f2064 22d92813 ef3f2064 000055cb
3cc0: ef3f2050 c031a19c ef252000 00000000 00000000 c0561bc0 00000000 ff00ffff
3ce0: c05621c0 ef3a5400 ef3f2064 ee573840 00000020 ef3f2064 000055cb ef3f2050
3d00: c053f0e0 c031cad0 c053e740 00000e60 00000000 00000000 ee573840 ef3a5400
3d20: ef0a6e00 00000000 ef3f2064 c032507c 00010000 00000020 c0561bc0 c0561bc0
3d40: ee599850 c032799c 00000000 ee573840 c055a380 ef3a5400 00000000 ef3f2064
3d60: ef3f2050 c032799c 0101c7c0 2b6755cb c059a280 c030e4d8 000055cb ffffffff
3d80: ee574fc0 c055a380 ee574000 ee573840 00002b67 ee573840 c03fe9c4 c053fa68
3da0: c055a380 00001f6f 00000000 ee573840 c053f0e0 c0304fdc ef0a6e01 ef3f2050
3dc0: ee573858 ef031000 ee573840 c03055d8 c0ba0c40 ef000f40 00100100 c053f0dc
3de0: c053ffdc c053f0f0 00000008 00000000 ef031000 c02da948 00001140 00000000
3e00: c0563c78 ef253e5f 00000020 ee573840 00000020 c053f0f0 ef313400 ee573840
3e20: c053f0e0 00000000 00000000 c05380c0 ef313400 00001000 00000015 c02df280
3e40: ee574000 ef001e00 00000000 00001080 00000042 005cd980 ef031500 ef031500
3e60: 00000000 c02df824 ef031500 c053e390 c0541084 f00b1e00 c05925e8 c02df864
3e80: 00001f5c ef031440 c053e390 c0278524 00000002 00000000 c0b9eb48 c02df280
3ea0: ee8c7180 00000100 c0542ca8 00000015 00000040 ef031500 ef031500 ef031500
3ec0: c027803c ef252000 00000040 000000ec c05380c0 c0b9eb40 c0b9eb48 c02df940
3ee0: ef060780 ffffa4dd c0564a9c c056343c 002e80a8 00000080 ef031500 00000001
3f00: c053808c ef252000 fffec100 00000003 00000004 002e80a8 0000000c c00258f0
3f20: 002e80a8 c005e704 00000005 00000100 c05634d0 c0538080 c05333e0 00000000
3f40: 0000000a c0565580 c05380c0 ffffa4dc c05434f4 00400100 00000004 c0534cd4
3f60: 00000098 00000000 fffec100 002e80a8 00000004 002e80a8 002a20e0 c0025da8
3f80: c0534cd4 c000f020 fffec10c c053ea60 ef253fb0 c0008530 0000ffe2 b6ef67f4
3fa0: 40000010 ffffffff 00000124 c0012f3c 0000ffe2 002e80f0 0000ffe2 00004000
3fc0: becb6338 becb6334 00000004 00000124 002e80a8 00000004 002e80a8 002a20e0
3fe0: becb6300 becb62f4 002773bb b6ef67f4 40000010 ffffffff 00000000 00000000
[<c03c7c3c>] (skb_panic+0x60/0x64) from [<c02d0ef0>] (skb_put+0x4c/0x50)
[<c02d0ef0>] (skb_put+0x4c/0x50) from [<c0318f8c>] (tcp_collapse+0x314/0x3ec)
[<c0318f8c>] (tcp_collapse+0x314/0x3ec) from [<c0319214>]
(tcp_try_rmem_schedule+0x1b0/0x3c4)
[<c0319214>] (tcp_try_rmem_schedule+0x1b0/0x3c4) from [<c031a19c>]
(tcp_data_queue+0x480/0xe6c)
[<c031a19c>] (tcp_data_queue+0x480/0xe6c) from [<c031cad0>]
(tcp_rcv_established+0x180/0x62c)
[<c031cad0>] (tcp_rcv_established+0x180/0x62c) from [<c032507c>]
(tcp_v4_do_rcv+0x13c/0x31c)
[<c032507c>] (tcp_v4_do_rcv+0x13c/0x31c) from [<c032799c>]
(tcp_v4_rcv+0x718/0x73c)
[<c032799c>] (tcp_v4_rcv+0x718/0x73c) from [<c0304fdc>]
(ip_local_deliver+0x98/0x274)
[<c0304fdc>] (ip_local_deliver+0x98/0x274) from [<c03055d8>]
(ip_rcv+0x420/0x758)
[<c03055d8>] (ip_rcv+0x420/0x758) from [<c02da948>]
(__netif_receive_skb_core+0x44c/0x5bc)
[<c02da948>] (__netif_receive_skb_core+0x44c/0x5bc) from [<c02df280>]
(netif_receive_skb+0x48/0xb4)
[<c02df280>] (netif_receive_skb+0x48/0xb4) from [<c02df824>]
(napi_gro_flush+0x70/0x94)
[<c02df824>] (napi_gro_flush+0x70/0x94) from [<c02df864>]
(napi_complete+0x1c/0x34)
[<c02df864>] (napi_complete+0x1c/0x34) from [<c0278524>]
(stmmac_poll+0x4e8/0x5c8)
[<c0278524>] (stmmac_poll+0x4e8/0x5c8) from [<c02df940>]
(net_rx_action+0xc4/0x1e4)
[<c02df940>] (net_rx_action+0xc4/0x1e4) from [<c00258f0>]
(__do_softirq+0x12c/0x2e8)
[<c00258f0>] (__do_softirq+0x12c/0x2e8) from [<c0025da8>] (irq_exit+0x78/0xac)
[<c0025da8>] (irq_exit+0x78/0xac) from [<c000f020>] (handle_IRQ+0x44/0x90)
[<c000f020>] (handle_IRQ+0x44/0x90) from [<c0008530>]
(gic_handle_irq+0x2c/0x5c)
[<c0008530>] (gic_handle_irq+0x2c/0x5c) from [<c0012f3c>]
(__irq_usr+0x3c/0x60)
3) The driver was setting the dma buffer size after allocating dma buffers,
which caused a system panic when changing the MTU.
BUG: Bad page state in process ifconfig pfn:2e850
page:c0b72a00 count:0 mapcount:0 mapping: (null) index:0x0
page flags: 0x200(arch_1)
Modules linked in:
CPU: 0 PID: 566 Comm: ifconfig Not tainted 3.13.0-rc6-01523-gf7111b9 #29
[<c001547c>] (unwind_backtrace+0x0/0xf8) from [<c00122dc>]
(show_stack+0x10/0x14)
[<c00122dc>] (show_stack+0x10/0x14) from [<c03c793c>] (dump_stack+0x70/0x88)
[<c03c793c>] (dump_stack+0x70/0x88) from [<c00b2620>] (bad_page+0xc8/0x118)
[<c00b2620>] (bad_page+0xc8/0x118) from [<c00b302c>]
(get_page_from_freelist+0x744/0x870)
[<c00b302c>] (get_page_from_freelist+0x744/0x870) from [<c00b40f4>]
(__alloc_pages_nodemask+0x118/0x86c)
[<c00b40f4>] (__alloc_pages_nodemask+0x118/0x86c) from [<c00b4858>]
(__get_free_pages+0x10/0x54)
[<c00b4858>] (__get_free_pages+0x10/0x54) from [<c00cba1c>]
(kmalloc_order_trace+0x24/0xa0)
[<c00cba1c>] (kmalloc_order_trace+0x24/0xa0) from [<c02d199c>]
(__kmalloc_reserve.isra.21+0x24/0x70)
[<c02d199c>] (__kmalloc_reserve.isra.21+0x24/0x70) from [<c02d240c>]
(__alloc_skb+0x68/0x13c)
[<c02d240c>] (__alloc_skb+0x68/0x13c) from [<c02d3930>]
(__netdev_alloc_skb+0x3c/0xe8)
[<c02d3930>] (__netdev_alloc_skb+0x3c/0xe8) from [<c0279378>]
(stmmac_open+0x63c/0x1024)
[<c0279378>] (stmmac_open+0x63c/0x1024) from [<c02e18cc>]
(__dev_open+0xa0/0xfc)
[<c02e18cc>] (__dev_open+0xa0/0xfc) from [<c02e1b40>]
(__dev_change_flags+0x94/0x158)
[<c02e1b40>] (__dev_change_flags+0x94/0x158) from [<c02e1c24>]
(dev_change_flags+0x18/0x48)
[<c02e1c24>] (dev_change_flags+0x18/0x48) from [<c0337bc0>]
(devinet_ioctl+0x638/0x700)
[<c0337bc0>] (devinet_ioctl+0x638/0x700) from [<c02c7aec>]
(sock_ioctl+0x64/0x290)
[<c02c7aec>] (sock_ioctl+0x64/0x290) from [<c0100890>]
(do_vfs_ioctl+0x78/0x5b8)
[<c0100890>] (do_vfs_ioctl+0x78/0x5b8) from [<c0100e0c>] (SyS_ioctl+0x3c/0x5c)
[<c0100e0c>] (SyS_ioctl+0x3c/0x5c) from [<c000e760>]
The fixes have been verified using reproducible, automated testing.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When timestamping is enabled, stmmac_tx_clean will call
stmmac_get_tx_hwtstamp to get tx TS.
But the skb can be NULL because the last of its tx_skbuff is NULL
if this packet frame is filled in more than one descriptors.
To fix the issue, change the code:
- Store TX skb to the tx_skbuff[] of frame's last segment.
- Check skb is not NULL in stmmac_get_tx_hwtstamp.
Signed-off-by: Bruce Liu <damuzi000@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Allwinner A20 has an ethernet controller that seems to be
an early version of Synopsys DesignWare MAC 10/100/1000 Universal,
which is supported by the stmmac driver.
Allwinner's GMAC requires setting additional registers in the SoC's
clock control unit.
The exact version of the DWMAC IP that Allwinner uses is unknown,
thus the exact feature set is unknown.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
The stmmac driver core allows passing feature flags and callbacks via
platform data. Add a similar stmmac_of_data to pass flags and callbacks
tied to compatible strings. This allows us to extend stmmac with glue
layers for different SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
The snps,phy-addr device tree property is non-standard, and should be
removed in favor of proper phy node support. Remove it from the binding
documents and warn if the property is still used.
Most PHYs respond to address 0, but a few don't, so auto-detect PHY
address by default, to make up for the lack of explicit address selection.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
"snps,force_sf_dma_mode" is documented in stmmac device tree bindings,
but is never handled by the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
The current .init and .exit callbacks requires access to driver
private data structures. This is not a good seperation and abstraction.
Instead, we add a new .setup callback for allocating private data, and
pass the returned pointer to the other callbacks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
The DWMAC has a reset assert line, which is used on some SoCs. Add an
optional reset control to stmmac driver core.
To support reset control deferred probing, this patch changes the driver
probe function to return the actual error, instead of just -EINVAL.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
The stmmac driver does not enable the main clock during the probe phase.
If the clock was not enabled by the boot loader or was disabled by the
kernel, hardware features and the MDIO bus would not be probed properly.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In PM_SUSPEND_FREEZE and WOL(Wakeup On Lan) case, when the driver gets a
wakeup event, either the driver or platform specific PM code should notify
the pm core about it, so that the system can wakeup from low power.
In cases where there is no involvement of platform specific PM, it
becomes driver responsibility to notify the PM core to wakeup the
system.
Without this WOL with PM_SUSPEND_FREEZE does not work on STi based SOCs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds code to restore default pinstate of the pins when it
comes back from low power state. Without this patch the state of the
pins would be unknown and the driver would not work.
This patch also adds code to put the pins in to sleep state when the
driver enters low power state.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In hibernation freeze case the driver just releases the resources like
dma buffers, irqs, unregisters the drivers and during restore it does
register, request the resources. This is not really necessary, as part
of power management all the data structures are intact, all the
previously allocated resources can be used after coming out of low
power.
This patch uses the suspend and resume callbacks for freeze and
restore which initializes the hardware correctly without unregistering
or releasing the resources, this should also help in reducing the time
to restore.
Also this patch fixes a bug in stmmac_pltfr_restore and
stmmac_pltfr_freeze where it tries to get hold of platform data via
dev_get_platdata call, which would return NULL in device tree cases and
the next if statement would crash as there is no NULL check.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The driver PM resume assumes that the IP is still powered up and the
all the register contents are not disturbed when it comes out of low
power suspend case. This assumption is wrong, basically the driver
should not consider any state of registers after it comes out of low
power. However driver can keep the part of the IP powered up if its a
wake up source. But it can not assume the register state of the IP. Also
its possible that SOC glue layer can take the power off the IP if its
not wake-up source to reduce the power consumption.
This patch re initializes hardware by calling stmmac_hw_setup function in
resume case.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
This patch promotes stmmac_mdio_reset function from static to
non-static, so that power management functions can decide to reset if
the IP comes out from lowe power state specially hibernation cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch moves hardware setup part of the code in stmmac_open to a new
function stmmac_hw_setup, the reason for doing this is to make hw
initialization independent function so that PM functions can re-use it to
re-initialize the IP after returning from low power state.
This will also avoid code duplication across stmmac_resume/restore and
stmmac_open.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch moves dma resource allocation to a new function
alloc_dma_desc_resources, the reason for moving this to a new function
is to keep the memory allocations in a separate function. One more reason
it to get suspend and hibernation cases working without releasing and
allocating these resources during suspend-resume and freeze-restore
cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
This patch removes gpio_free for reset line of the phy, driver stores
the gpio number in its private data-structure to use in future. As the
driver uses this pin in future this pin should not be freed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support to "max-speed" property which is a standard
Ethernet device tree property. max-speed specifies maximum speed
(specified in megabits per second) supported the device.
Depending on the clocking schemes some of the boards can only support
few link speeds, so having a way to limit the link speed in the mac
driver would allow such setups to work reliably.
Without this patch there is no way to tell the driver to limit the
link speed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
GRO requires VLANs to be removed before aggregation can occur.
The Synopsys EMAC does not strip VLAN tags so this must be
done by the driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch corrects a problem in stmmac_ptp.c, functions
stmmac_adjust_time and stmmac_adjust_freq where the incorrect spinlocks
were released. This patch also addresses a problem in stmmac_main,
function stmmac_init_ptp where the capability detection for
advanced timestamping was masked by message masking.
This patch was touch tested using linuxptp, and runs without the previously
observed instabilities. More extensive testing is ongoing.
Vince
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Make variables only used in one file static. Also avoids possible
namespace collisions.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch marks the function stmmac_pltfr_freeze() and
stmmac_pltfr_restore() in stmmac_platform.c as static because they are
not used outside this file.
Thus, it also removes the following warnings in
ethernet/stmicro/stmmac/stmmac_platform.c:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:222:5: warning: no previous prototype for ‘stmmac_pltfr_freeze’ [-Wmissing-prototypes]
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:236:5: warning: no previous prototype for ‘stmmac_pltfr_restore’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
stmmac_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes. Currently it sets the TX configuration
before validating the rx_filter field.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Merge commit 06c54055bebf did a bad conflict resolution accidentally
leaving out a closing brace. Add it back.
This breaks a handful of defconfigs on ARM, so it'd be good to see it
applied pretty quickly.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch fixed the pbl(programmable burst length) setting
using DT. Even though the default pbl is 8, If there is no
pbl property in device tree file, pbl is set 0 and it causes
bandwidth degradation.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Time stamp binary rollover is set.
The synopsys spec says When TSCRLSSR is cleard, the rollover value of
sub-second register is 0x7FFFFFFF(0.465 ns per clock).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
force_thresh_dma_mode is set.
Some synopsys ip implementation doesn't support DMA store and forward mode,
such as BF60x. So, set force_thresh_dma_mode to use DMA thresholds only.
Update document and devicetree as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch removes the no_csum_insertion private parameter that is not used anymore
and, also, the "likely" annotation from the condition that is not in a critical path.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \
| |/ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In stmmac_init_rx_buffers():
* add missing handling of dma_map_single() error
* remove superfluous unlikely() optimization while at it
Add stmmac_free_rx_buffers() helper and use it in dma_free_rx_skbufs().
In init_dma_desc_rings():
* add missing handling of kmalloc_array() errors
* fix handling of dma_alloc_coherent() and stmmac_init_rx_buffers() errors
* make function return an error value on error and 0 on success
In stmmac_open():
* add handling of init_dma_desc_rings() return value
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch fixed the condition of extend_desc for jumbo frame.
There is no check routine for extend_desc in the stmmac_jumbo_frm function.
Even though extend_desc is set if dma_tx is used instead of dma_etx.
It causes kernel panic.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
|
| |
devm_ioremap_resource
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds phy reset callback support for stmmac driver via device
trees. It adds three new properties to gmac device tree bindings to
define the reset signal via gpio.
With this patch users can conveniently pass reset gpio number with pre,
pulse and post delay in micro secs via DTs.
active low:
_________ ____________
<pre-delay> |<pulse-delay> |<post-delay>
| |
|_______________|
active high:
________________
<pre-delay> |<pulse-delay> |<post-delay>
| |
________| |___________
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|