| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
| |
Add device name for Mellanox FPGA devices.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
|
|
|
|
|
|
|
|
| |
Currently, FPGA capability is located in (mdev)->caps.hca_cur,
change the location to be (mdev)->caps.fpga,
since hca_cur is reserved for HCA device capabilities.
Fixes: e29341fb3a5b ("net/mlx5: FPGA, Add basic support for Innova")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add interface to initialize and interact with Innova FPGA SBU
connections.
A client driver may use these functions to set up a high-speed DMA
connection with its SBU hardware logic, and send/receive messages
over this connection.
A later patch in this patchset will make use of these functions for
Innova IPSec offload in mlx5 Ethernet driver.
Add commands to retrieve Innova FPGA SBU capabilities, and to
read/write Innova FPGA configuration space registers and memory,
over internal I2C.
At high level, the FPGA configuration space is divided such:
0x00000000 - 0x007fffff is reserved for the SBU
0x00800000 - 0xffffffff is reserved for the Shell
0x400000000 - ... is DDR memory
A later patchset will add support for accessing FPGA CrSpace and memory
over a high-speed connection. This is the reason for the ACCESS_TYPE
enumeration, which currently only supports I2C.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Innova FPGA includes shell hardware and Sandbox-Unit (SBU) hardware.
The shell hardware is handled by mlx5_core itself, while the SBU is
handled by a client driver.
Reset the SBU to a well-known initial state when initializing a new
device, and set the FPGA to bypass mode when uninitializing a device.
This allows the client driver to assume that its device has been
reset when a new device is detected.
During SBU reset, the FPGA is put into SBU-bypass mode. In this mode
packets do not pass through the SBU, so it cannot affect the network
data stream at all.
A factory-image does not have an SBU, so skip these flows.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
The FPGA QP is a high-bandwidth communication channel between the host
CPU and the FPGA device. It allows performing DMA operations between
host memory and the FPGA logic via the ConnectX chip.
Add ConnectX FW commands which create and manipulate FPGA QPs.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
|
Mellanox Innova is a NIC with ConnectX and an FPGA on the same
board. The FPGA is a bump-on-the-wire and thus affects operation of
the mlx5_core driver on the ConnectX ASIC.
Add basic support for Innova in mlx5_core.
This allows using the Innova card as a regular NIC, by detecting
the FPGA capability bit, and verifying its load state before
initializing ConnectX interfaces.
Also detect FPGA fatal runtime failures and enter error state if
they ever happen.
All new FPGA-related logic is placed in its own subdirectory 'fpga',
which may be built by selecting CONFIG_MLX5_FPGA.
This prepares for further support of various Innova features in later
patchsets.
Additional details about hardware architecture will be provided as
more features get submitted.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
