summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/freescale/gianfar.c
Commit message (Collapse)AuthorAgeFilesLines
* net/fsl: constify of_device_id arrayFabian Frederick2015-03-171-1/+1
| | | | | | | | of_device_id is always used as const. (See driver.of_match_table and open firmware functions) Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Consider dts property endianess on handlingJingchang Lu2015-03-151-30/+47
| | | | | | | | | Use of_property_read*() to get arch endian consistent property values. Do some refactoring in the process. Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Make FCB access endian safeClaudiu Manoil2015-03-151-8/+9
| | | | | | | | Use conversion macros to correctly access the BE fields of the Rx and Tx Frame Control Block on LE CPUs. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Make BDs access endian safeClaudiu Manoil2015-03-151-46/+62
| | | | | | | | Use conversion macros to correctly access the BE fields of the Rx and Tx Buffer Descriptors on LE CPUs. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: gianfar: correctly determine the number of queue groupsTobias Waldekranz2015-03-051-2/+17
| | | | | | | | | | | | eTSEC of-nodes may have children which are not queue-group nodes. For example new-style fixed-phy declarations. These where incorrectly assumed to be additional queue-groups. Change the search to filter out any nodes which are not queue-groups, or have been disabled. Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Reduce logging noise seen due to phy polling if link is downGuenter Roeck2015-03-031-2/+2
| | | | | | | | | | | | | | | | | | | | Commit 6ce29b0e2a04 ("gianfar: Avoid unnecessary reg accesses in adjust_link()") eliminates unnecessary calls to adjust_link for phy devices which don't support interrupts and need polling. As part of that work, the 'new_state' local flag, which was used to reduce logging noise on the console, was eliminated. Unfortunately, that means that a 'Link is Down' log message will now be issued continuously if a link is configured as UP, the link state is down, and the associated phy requires polling. This occurs because priv->oldduplex is -1 in this case, which always differs from phydev->duplex. In addition, phydev->speed may also differ from priv->oldspeed. gfar_update_link_state() is therefore called each time a phy is polled, even if the link state did not change. Cc: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: gianfar: remove the unneeded check of disabled deviceKevin Hao2015-01-291-1/+1
| | | | | | | | | Since commit cd1e65044d44 ("of/device: Don't register disabled devices"), the disabled device will not be registered at all. So we don't need to do the check again in the platform device driver. Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: rename vlan_tx_* helpers since "tx" is misleading thereJiri Pirko2015-01-131-2/+2
| | | | | | | The same macros are used for rx as well. So rename it. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: gianfar: add missing __iomem annotationKevin Hao2014-12-301-1/+1
| | | | | | | | | | | | | | | | Fix the following spare warning: drivers/net/ethernet/freescale/gianfar.c:3521:60: warning: incorrect type in argument 1 (different address spaces) drivers/net/ethernet/freescale/gianfar.c:3521:60: expected unsigned int [noderef] <asn:2>*addr drivers/net/ethernet/freescale/gianfar.c:3521:60: got unsigned int [usertype] *rfbptr drivers/net/ethernet/freescale/gianfar.c:205:16: warning: incorrect type in assignment (different address spaces) drivers/net/ethernet/freescale/gianfar.c:205:16: expected unsigned int [usertype] *rfbptr drivers/net/ethernet/freescale/gianfar.c:205:16: got unsigned int [noderef] <asn:2>*<noident> drivers/net/ethernet/freescale/gianfar.c:2918:44: warning: incorrect type in argument 1 (different address spaces) drivers/net/ethernet/freescale/gianfar.c:2918:44: expected unsigned int [noderef] <asn:2>*addr drivers/net/ethernet/freescale/gianfar.c:2918:44: got unsigned int [usertype] *rfbptr Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: gianfar: mark the local functions staticKevin Hao2014-12-301-4/+5
| | | | | Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge tag 'driver-core-3.19-rc1' of ↵Linus Torvalds2014-12-141-1/+0
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core update from Greg KH: "Here's the set of driver core patches for 3.19-rc1. They are dominated by the removal of the .owner field in platform drivers. They touch a lot of files, but they are "simple" changes, just removing a line in a structure. Other than that, a few minor driver core and debugfs changes. There are some ath9k patches coming in through this tree that have been acked by the wireless maintainers as they relied on the debugfs changes. Everything has been in linux-next for a while" * tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits) Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries" fs: debugfs: add forward declaration for struct device type firmware class: Deletion of an unnecessary check before the function call "vunmap" firmware loader: fix hung task warning dump devcoredump: provide a one-way disable function device: Add dev_<level>_once variants ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries ath: use seq_file api for ath9k debugfs files debugfs: add helper function to create device related seq_file drivers/base: cacheinfo: remove noisy error boot message Revert "core: platform: add warning if driver has no owner" drivers: base: support cpu cache information interface to userspace via sysfs drivers: base: add cpu_device_create to support per-cpu devices topology: replace custom attribute macros with standard DEVICE_ATTR* cpumask: factor out show_cpumap into separate helper function driver core: Fix unbalanced device reference in drivers_probe driver core: fix race with userland in device_add() sysfs/kernfs: make read requests on pre-alloc files use the buffer. sysfs/kernfs: allow attributes to request write buffer be pre-allocated. fs: sysfs: return EGBIG on write if offset is larger than file size ...
| * net: ethernet: freescale: drop owner assignment from platform_driversWolfram Sang2014-10-201-1/+0
| | | | | | | | | | | | | | A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* | gianfar: Fix dma check map error when DMA_API_DEBUG is enabledKevin Hao2014-12-111-28/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We need to use dma_mapping_error() to check the dma address returned by dma_map_single/page(). Otherwise we would get warning like this: WARNING: at lib/dma-debug.c:1140 Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.18.0-rc2-next-20141029 #196 task: c0834300 ti: effe6000 task.ti: c0874000 NIP: c02b2c98 LR: c02b2c98 CTR: c030abc4 REGS: effe7d70 TRAP: 0700 Not tainted (3.18.0-rc2-next-20141029) MSR: 00021000 <CE,ME> CR: 22044022 XER: 20000000 GPR00: c02b2c98 effe7e20 c0834300 00000098 00021000 00000000 c030b898 00000003 GPR08: 00000001 00000000 00000001 749eec9d 22044022 1001abe0 00000020 ef278678 GPR16: ef278670 ef278668 ef278660 070a8040 c087f99c c08cdc60 00029000 c0840d44 GPR24: c08be6e8 c0840000 effe7e78 ef041340 00000600 ef114e10 00000000 c08be6e0 NIP [c02b2c98] check_unmap+0x51c/0x9e4 LR [c02b2c98] check_unmap+0x51c/0x9e4 Call Trace: [effe7e20] [c02b2c98] check_unmap+0x51c/0x9e4 (unreliable) [effe7e70] [c02b31d8] debug_dma_unmap_page+0x78/0x8c [effe7ed0] [c03d1640] gfar_clean_rx_ring+0x208/0x488 [effe7f40] [c03d1a9c] gfar_poll_rx_sq+0x3c/0xa8 [effe7f60] [c04f8714] net_rx_action+0xc0/0x178 [effe7f90] [c00435a0] __do_softirq+0x100/0x1fc [effe7fe0] [c0043958] irq_exit+0xa4/0xc8 [effe7ff0] [c000d14c] call_do_irq+0x24/0x3c [c0875e90] [c00048a0] do_IRQ+0x8c/0xf8 [c0875eb0] [c000ed10] ret_from_except+0x0/0x18 For TX, we need to unmap the pages which has already been mapped and free the skb before return. For RX, move the dma mapping and error check to gfar_new_skb(). We would reuse the original skb in the rx ring when either allocating skb failure or dma mapping error. Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | gianfar: Implement PAUSE frame generation supportMatei Pavaluca2014-10-291-0/+54
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The hardware can automatically generate pause frames when the number of free buffers drops under a certain threshold, but in order to do this, the address of the last free buffer needs to be written to a specific register for each RX queue. This has to be done in 'gfar_clean_rx_ring' which is called for each RX queue. In order not to impact performance, by adding a register write for each incoming packet, this operation is done only when the PAUSE frame transmission is enabled. Whenever the link is readjusted, this capability is turned on or off. Signed-off-by: Matei Pavaluca <matei.pavaluca@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Fix the way the local advertising flow options are determinedPavaluca Matei-B466102014-10-291-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | Local flow control options needed in order to resolve the negotiation are incorrectly calculated. Previously 'mii_advertise_flowctrl' was called to determine the local advertising options, but these were determined based on FLOW_CTRL_RX/TX flags which are never set through ethtool. The patch simply translates from ethtool flow options to mii flow options. Signed-off-by: Pavaluca Matei <matei.pavaluca@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Add flow control support flags to gianfar's capabilitiesPavaluca Matei-B466102014-10-291-0/+3
|/ | | | | | | | | | | | The phy device supports 802.3x flow control, but the specific flags are not set in the phy initialisation code. Flow control flags need to be added to the supported capabilities of the phydev by the driver. This is needed in order for ethtool to work ('ethtool -A' code checks for these flags) Signed-off-by: Pavaluca Matei <matei.pavaluca@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Add FCS to rx buffer size (fix)Claudiu Manoil2014-10-151-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For each Rx frame the eTSEC writes its FCS (Frame Check Sequence) to the Rx buffer. The eTSEC h/w manual states in the "Receive Buffer Descriptor Field Descriptions" table: "Data length is the number of octets written by the eTSEC into this BD's data buffer if L is cleared (the value is equal to MRBLR), or, if L is set, the length of the frame including *CRC*, FCB (if RCTRL[PRSDEP > 00), preamble (if MACCFG2[PreAmRxEn]=1), time stamp (if RCTRL[TS] = 1) and any padding (RCTRL[PAL])." Though the FCS bytes are removed by the driver before passing the skb to the net stack, the Rx buffer size computation does not currently take into account the FCS bytes (4 bytes). Because the Rx buffer size is multiple of 512 bytes, leaving out the FCS is not a problem for the default MTU of 1500, as the Rx buffer size is 1536 in this case. However, for custom MTUs, where the difference between the MTU size and the Rx buffer size is less, this can be a problem as the computed Rx buffer size won't be enough to accomodate the FCS for a received frame that is big enough (close to MTU size). In such case the received frame is considered to be incomplete (L flag not set in the RxBD status) and silently dropped. Note that the driver does not currently support S/G on Rx, so it has to compute its Rx buffer size based on the MTU of the device. Reported-by: Kristian Otnes <kotnes@cisco.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Replace eieio with wmb for non-PPC archsClaudiu Manoil2014-10-091-10/+3
| | | | | | | | | | Replace PPC specific eieio() with arch independent wmb() for other architectures, i.e. ARM. The eieio() macro is not defined on ARM and generates build error. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Replace spin_event_timeout() with arch independentClaudiu Manoil2014-10-091-13/+19
| | | | | | | | | | Use arch independent code to replace the powerpc dependent spin_event_timeout() from gfar_halt_nodisable(). Added GRS/GTS read accessors to clean-up the implementation of gfar_halt_nodisable(). Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Make MAC addr setup endian safe, cleanupClaudiu Manoil2014-10-091-8/+7
| | | | | | | | | | | | Fix the 32-bit memory access that is not endian safe, i.e. not giving the desired byte layout for a LE CPU: tempval = *((u32 *) (tmpbuf + 4)), where 'char tmpbuf[]'. Get rid of rendundant local vars (tmpbuf[] and idx) and forced casts. Cleanup comments. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Exclude PPC specific errata handling from ARM buildsClaudiu Manoil2014-10-091-0/+6
| | | | | | | | | | This excludes the PPC specific instructions for PPC based SoC (MPC85xx family) version identification from ARM builds. The PPC specific macro mfspr() from asm/reg.h is not defined by the ARM architecture. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Include missing headers for ARM buildsClaudiu Manoil2014-10-091-0/+2
| | | | | | | | | | | | Include linux/of_address.h for of_iomap() and linux/of_irq.h for irq_of_parse_and_map(). This wasn't an issue for PPC, because these were implicitly included from asm/prom.h (via linux/of.h) for PPC builds only. ARM builds need these includes explicitly. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: gianfar: fix reference counting for phy_nodeUwe Kleine-König2014-08-071-2/+2
| | | | | | | | | | | | | | | | | | The line before the changed if condition is: priv->phy_node = of_parse_phandle(np, "phy-handle", 0); . If this call succeeds priv->phy_node must not be overwritten in the if block; otherwise the reference to the node returned by of_parse_phandle is lost. So add a check that the if block isn't executed in this case. Furthermore in the fixed phy case no reference is aquired for phy_node resulting in an of_node_put without holding a reference. To fix that, get a reference on the MAC dt node. Fixes: be40364544bd ("gianfar: use the new fixed PHY helpers") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: gianfar: no need to check parameter being != NULL for of_node_putUwe Kleine-König2014-08-071-8/+4
| | | | | | | of_node_put is a noop when being called with NULL. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds2014-06-121-7/+15
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: 1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov. 2) Multiqueue support in xen-netback and xen-netfront, from Andrew J Benniston. 3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn Mork. 4) BPF now has a "random" opcode, from Chema Gonzalez. 5) Add more BPF documentation and improve test framework, from Daniel Borkmann. 6) Support TCP fastopen over ipv6, from Daniel Lee. 7) Add software TSO helper functions and use them to support software TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia. 8) Support software TSO in fec driver too, from Nimrod Andy. 9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli. 10) Handle broadcasts more gracefully over macvlan when there are large numbers of interfaces configured, from Herbert Xu. 11) Allow more control over fwmark used for non-socket based responses, from Lorenzo Colitti. 12) Do TCP congestion window limiting based upon measurements, from Neal Cardwell. 13) Support busy polling in SCTP, from Neal Horman. 14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru. 15) Bridge promisc mode handling improvements from Vlad Yasevich. 16) Don't use inetpeer entries to implement ID generation any more, it performs poorly, from Eric Dumazet. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits) rtnetlink: fix userspace API breakage for iproute2 < v3.9.0 tcp: fixing TLP's FIN recovery net: fec: Add software TSO support net: fec: Add Scatter/gather support net: fec: Increase buffer descriptor entry number net: fec: Factorize feature setting net: fec: Enable IP header hardware checksum net: fec: Factorize the .xmit transmit function bridge: fix compile error when compiling without IPv6 support bridge: fix smatch warning / potential null pointer dereference via-rhine: fix full-duplex with autoneg disable bnx2x: Enlarge the dorq threshold for VFs bnx2x: Check for UNDI in uncommon branch bnx2x: Fix 1G-baseT link bnx2x: Fix link for KR with swapped polarity lane sctp: Fix sk_ack_backlog wrap-around problem net/core: Add VF link state control policy net/fsl: xgmac_mdio is dependent on OF_MDIO net/fsl: Make xgmac_mdio read error message useful net_sched: drr: warn when qdisc is not work conserving ...
| * Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2014-06-051-3/+3
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/xen-netback/netback.c net/core/filter.c A filter bug fix overlapped some cleanups and a conversion over to some new insn generation macros. A xen-netback bug fix overlapped the addition of multi-queue support. Signed-off-by: David S. Miller <davem@davemloft.net>
| | * gianfar: Call netif_carrier_off() prior to registrationFabio Estevam2014-06-051-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Quoting David Miller: "At the moment you call register_netdev() the device is visible, notifications are sent to userspace, and userland tools can try to bring the interface up and see the incorrect link state, before you do the netif_carrier_off(). Said another way, between the register_netdev() and netif_carrier_off() call, userspace can see the device in an inconsistent state." So call netif_carrier_off() prior to register_netdev(). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | gianfar: Fix the section mismatch warnings.Xiubo Li2014-06-041-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Building with CONFIG_DEBUG_SECTION_MISMATCH enabled, the following WARNING is occured: LD drivers/net/built-in.o WARNING: drivers/net/built-in.o(.text+0xcd4c): Section mismatch in reference from the function gfar_probe() to the function .init.text:gfar_init_addr_hash_table() The function gfar_probe() references the function __init gfar_init_addr_hash_table(). This is often because gfar_probe lacks a __init annotation or the annotation of gfar_init_addr_hash_table is wrong. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | gianfar: use the new fixed PHY helpersFlorian Fainelli2014-05-221-3/+11
| |/ | | | | | | | | | | | | | | | | | | | | of_phy_connect_fixed_link() is becoming obsolete, and also required platform code to register the fixed PHYs at the specified addresses for those to be usable. Get rid of it and use the new of_phy_is_fixed_link() plus of_phy_register_fixed_link() helpers to transition over the new scheme. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'locking-core-for-linus' of ↵Linus Torvalds2014-06-031-4/+4
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next Pull core locking updates from Ingo Molnar: "The main changes in this cycle were: - reduced/streamlined smp_mb__*() interface that allows more usecases and makes the existing ones less buggy, especially in rarer architectures - add rwsem implementation comments - bump up lockdep limits" * 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits) rwsem: Add comments to explain the meaning of the rwsem's count field lockdep: Increase static allocations arch: Mass conversion of smp_mb__*() arch,doc: Convert smp_mb__*() arch,xtensa: Convert smp_mb__*() arch,x86: Convert smp_mb__*() arch,tile: Convert smp_mb__*() arch,sparc: Convert smp_mb__*() arch,sh: Convert smp_mb__*() arch,score: Convert smp_mb__*() arch,s390: Convert smp_mb__*() arch,powerpc: Convert smp_mb__*() arch,parisc: Convert smp_mb__*() arch,openrisc: Convert smp_mb__*() arch,mn10300: Convert smp_mb__*() arch,mips: Convert smp_mb__*() arch,metag: Convert smp_mb__*() arch,m68k: Convert smp_mb__*() arch,m32r: Convert smp_mb__*() arch,ia64: Convert smp_mb__*() ...
| * arch: Mass conversion of smp_mb__*()Peter Zijlstra2014-04-181-4/+4
| | | | | | | | | | | | | | | | | | | | | | Mostly scripted conversion of the smp_mb__* barriers. Signed-off-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Link: http://lkml.kernel.org/n/tip-55dhyhocezdw1dg7u19hmh1u@git.kernel.org Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: linux-arch@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* | gianfar: Avoid unnecessary reg accesses in adjust_link()Claudiu Manoil2014-04-301-110/+113
|/ | | | | | | | | | | | | | | | | | | For phy devices that don't issue interrupts upon link state changes, phylib polls the link state resulting in repeated calls to adjust_link(), even if the link state didn't change. As a result, some mac registers are repeatedly read and written with the same values, which is not ok. To fix this, adjust_link() has been refactored to check first whether the link state has changed and to take action only if needed, updating mac registers and local state variables. The 'new_state' local flag, set if one of the link params changed (link, speed or duplex), has been rendered useless and removed by this refactoring. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Fix P1010 config regression (SQ polling)Claudiu Manoil2014-03-241-2/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | The P1010 device tree restricts the number of supported interrupt groups to 1, although the eth controller can support 2 interrupt groups and the driver assumes the Multi-Group mode ("fsl,etsec2" model). So, in this case the assumption that the Multi-Group mode (MQ_MG_MODE) devices always support 2 interrupt groups is false. To fix this, a check for the actual number of interrupt groups enabled in the board's device tree has been added in gfar_probe for the "fsl,etsec2" devices. Without this fix, P1010 based boards claim support for 2 Tx queues to the net stack but only one is actually allocated, leading to NULL access in xmit. This issue was introduced by enabling Single-Queue polling for the P1010 devices. (71ff9e3 gianfar: Use Single-Queue polling for "fsl,etsec2") Fixes: 71ff9e3df7e1c5d3293af6b595309124e8c97412 Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Carefully free skbs in functions called by netpoll.Eric W. Biederman2014-03-121-2/+2
| | | | | | | | | | netpoll can call functions in hard irq context that are ordinarily called in lesser contexts. For those functions use dev_kfree_skb_any and dev_consume_skb_any so skbs are freed safely from hard irq context. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Fix multi-queue support checks @probe()Claudiu Manoil2014-03-121-10/+18
| | | | | | | | | | | | | | priv is not instantiated at gfar_of_init() time, when parsing the DT for info on supported HW queues. Before the netdev can be allocated, the number of supported queues must be known. Because the number of supported queues depends on device type, move the compatibility checks before netdev allocation. Local vars are used to hold the operation mode info before netdev allocation. This fixes the null accesses for priv->.., in gfar_of_init. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Use Single-Queue polling for "fsl,etsec2"Claudiu Manoil2014-03-101-22/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For the "fsl,etsec2" compatible models the driver currently supports 8 Tx and Rx DMA rings (aka HW queues). However, there are only 2 pairs of Rx/Tx interrupt lines, as these controllers are integrated in low power SoCs with 2 CPUs at most. As a result, there are at most 2 NAPI instances that have to service multiple Tx and Rx queues for these devices. This complicates the NAPI polling routine having to iterate over the mutiple Rx/Tx queues hooked to the same interrupt lines. And there's also an overhead at HW level, as the controller needs to service all the 8 Tx rings in a round robin manner. The combined overhead shows up for multi parallel Tx flows transmitted by the kernel stack, when the driver usually starts returning NETDEV_TX_BUSY leading to NETDEV WATCHDOG Tx timeout triggering if the Tx path is congested for too long. As an alternative, this patch makes the driver support only one Tx/Rx DMA ring per NAPI instance (per interrupt group or pair of Tx/Rx interrupt lines) by default. The simplified single queue polling routine (gfar_poll_sq) will be the default napi poll routine for the etsec2 devices too. Some adjustments needed to be made to link the Tx/Rx HW queues with each NAPI instance (2 in this case). The gfar_poll_sq() is already successfully used by older SQ_SG_MODE (single interrupt group) controllers. This patch fixes Tx timeout triggering under heavy Tx traffic load (i.e. iperf -c -P 8) for the "fsl,etsec2" (currently the only MQ_MG_MODE devices). There's also a significant memory footprint reduction by supporting 2 Rx/Tx DMA rings (at most), instead of 8, for these devices. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Separate out the Tx interrupt handling (Tx NAPI)Claudiu Manoil2014-03-101-65/+153
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are some concurrency issues on devices w/ 2 CPUs related to the handling of Rx and Tx interrupts. eTSEC has separate interrupt lines for Rx and Tx but a single imask register to mask these interrupts and a single NAPI instance to handle both Rx and Tx work. As a result, the Rx and Tx ISRs are identical, both are invoking gfar_schedule_cleanup(), however both handlers can be entered at the same time when the Rx and Tx interrupts are taken by different CPUs. In this case spurrious interrupts (SPU) show up (in /proc/interrupts) indicating a concurrency issue. Also, Tx overruns followed by Tx timeout have been observed under heavy Tx traffic load. To address these issues, the schedule cleanup ISR part has been changed to handle the Rx and Tx interrupts independently. The patch adds a separate NAPI poll routine for Tx cleanup to be triggerred independently by the Tx confirmation interrupts only. Existing poll functions are modified to handle only the Rx path processing. The Tx poll routine does not need a budget, since Tx processing doesn't consume NAPI budget, and hence it is registered with minimum NAPI weight. NAPI scheduling does not require locking since there are different NAPI instances between the Rx and Tx confirmation paths now. So, the patch fixes the occurence of spurrious Rx/Tx interrupts. Tx overruns also occur less frequently now. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Fix Tx int miss, dont write IC on-the-flyClaudiu Manoil2014-02-241-58/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | Programming the interrupt coalescing (IC) registers while the controller/DMA is on may incur the loss of one Tx confirmation interrupt, under certain conditions. This is a subtle hw race because it does not occur during a burst of Tx packets. It has been observed on p2020 devices that, if just one packet is being xmit'ed, the Tx confirmation doesn't trigger and BQL evetually blocks the Tx queues, followed by Tx timeout and an un-responsive device. This issue was not apparent prior to introducing BQL support, as a late Tx confirmation was not an issue back then and the next burst of Tx frames would have triggered the Tx confirmation/ Tx ring cleanup anyway. Bottom line, the hw specifications state that the IC registers should not be programmed while the Rx/Tx blocks (the DMA) are enabled. Further more, these registers are currently re-written with the same values on the processing path, over and over again. To fix this, rewriting the IC registers has been removed from the processing path (napi poll). A complete MAC reset procedure has been implemented for the ethtool -c option instead, to reliably update these registers while the controller is stopped. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Fix device reset races (oops) for TxClaudiu Manoil2014-02-241-68/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The device reset procedure, stop_gfar()/startup_gfar(), has concurrency issues. "Kernel access of bad area" oopses show up during Tx timeout device reset or other reset cases (like changing MTU) that happen while the interface still has traffic. The oopses happen in start_xmit and clean_tx_ring when accessing tx_queue-> tx_skbuff which is NULL. The race comes from de-allocating the tx_skbuff while transmission and napi processing are still active. Though the Tx queues get temoprarily stopped when Tx timeout occurs, they get re-enabled as a result of Tx congestion handling inside the napi context (see clean_tx_ring()). Not disabling the napi during reset is also a bug, because clean_tx_ring() will try to access tx_skbuff while it is being de-alloc'ed and re-alloc'ed. To fix this, stop_gfar() needs to disable napi processing after stopping the Tx queues. However, in order to prevent clean_tx_ring() to re-enable the Tx queue before the napi gets disabled, the device state DOWN has been introduced. It prevents the Tx congestion management from re-enabling the de-congested Tx queue while the device is brought down. An additional locking state, RESETTING, has been introduced to prevent simultaneous resets or to prevent configuring the device while it is resetting. The bogus 'rxlock's (for each Rx queue) have been removed since their purpose is not justified, as they don't prevent nor are suited to prevent device reset/reconfig races (such as this one). Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Don't free/request irqs on device resetClaudiu Manoil2014-02-241-32/+45
| | | | | | | | | | | | Resetting the device (stop_gfar()/startup_gfar()) should be fast and to the point, in order to timely recover from an error condition (like Tx timeout) or during device reconfig. The irq free/ request routines are just redundant here, and they should be part of the device close/ open routines instead. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Fix on-the-fly vlan and mtu updatesClaudiu Manoil2014-02-241-118/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RCTRL and TCTRL registers should not be changed on-the-fly, while the controller is running, otherwise unexpected behaviour occurs. But that's exactly what gfar_vlan_mode() does, updating the VLAN acceleration bits inside RCTRL/TCTRL. The attempt to lock these operations doesn't help, but only adds to the confusion. There's also a dependency for Rx FCB insertion (activating /de-activating the TOE offload block on Rx) which might change the required rx buffer size. This makes matters worse as gfar_vlan_mode() ends up calling gfar_change_mtu(), though the MTU size remains the same. Note that there are other situations that may affect the required rx buffer size, like changing RXCSUM or rx hw timestamping, but errorneously the rx buffer size is not recomputed/ updated in the process. To fix this, do the vlan updates properly inside the MAC reset and reconfiguration procedure, which takes care of the rx buffer size dependecy and the rx TOE block (PRSDEP) activation/deactivation as well (in the correct order). As a consequence, MTU/ rx buff size updates are done now by the same MAC reset and reconfig procedure, so that out of context updates to MAXFRM, MRBLR, and MACCFG inside change_mtu() are no longer needed. The rx buffer size dependecy to Rx FCB is now handled for the other cases too (RXCSUM and rx hw timestamping). Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Implement MAC reset and reconfig procedureClaudiu Manoil2014-02-241-82/+90
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The main MAC config registers like: RCTRL/TCTRL, MRBLR, MAXFRM, RXIC/TXIC, most fields of MACCFG1/2, should not be changed on-the-fly, but at least after stopping the DMA and disabling the Rx/Tx blocks and, for increased reliability, after a MAC soft reset. Impelement a complete MAC soft reset and reconfig procedure following the latest HW advisories - gfar_mac_reset() - to replace gfar_mac_init() and (the confusing) init_registers() functions. Factor out separate config functions for RCTRL and TCTRL, insure programming order of the relevant config regs after MAC soft reset. Split gfar_hw_init() into gfar_mac_reset() and the remaining global regs that don't need to be reconfigured after MAC soft reset (FIFOCFG, ATTRELI, HW counters a.s.o). As gfar_hw_init() now makes all the register writes @probe() time, based on all the device flags and config options, it must be moved further down, just before register_netdev(), as the last config step when the config values are comitted to HW. Also, move netif_carrier_off() after register_netdev(), because it has no effect if called before. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Add missing graceful reset steps and fixesClaudiu Manoil2014-02-181-26/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | gfar_halt() and gfar_start() are responsible for stopping and starting the DMA and the Rx/Tx hw rings. They implement the support for the "graceful Rx/Tx stop/start" hw procedure, and also disable/enable eTSEC's hw interrupts in the process. The GRS/GTS procedure requires however to have the RQUEUE/TQUEUE registers cleared first and to wait for a period of time for the current frame to pass through the interface (around ~10ms for a jumbo frame). Only then may the GTS and GRS bits from DMACTRL be set to shut down the DMA, and finally the Tx_EN and Rx_EN bits in MACCFG1 may be cleared to disable the Tx/Rx blocks. The same register programming order applies to start the Rx/Tx: enabling the RQUEUE/TQUEUE *before* clearing the GRS/GTS bits. This is a HW recommendation in order to avoid a possible controller "lock up" during graceful reset. Cleanup the gfar_halt()/start() prototypes, to take priv instead of ndev as their purpose is to operate on HW. Enabling the RQUEUE/TQUEUE in the hw_init() is not needed anymore since that's the job of gfar_start(). Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Factor out enabling/disabling of hw interruptsClaudiu Manoil2014-02-181-30/+30
| | | | | | | | | | | | | Throughout the code there are places where the controller's hw interrupt sources need to get disabled/enabled (masked/ un-masked) all at once. The recommendation for disabling the interrupts is to clear the ievent first then the imask register (not the other way around). Use the gfar_ints_enable/disable() helpers to make these operations consistent. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Remove useless HAS_PADDING device flagClaudiu Manoil2014-02-181-12/+3
| | | | | | | | | | | The RCTRL updates of the FSL_GIANFAR_DEV_HAS_PADDING device flag get overriden by the FSL_GIANFAR_DEV_HAS_TIMER flag settings, which impose a Rx padding alignment of 8 bytes. As all the eTSEC devices that set HAS_PADDING also set the HAS_TIMER flag, the HAS_PADDING flag is now obsolete. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Remove sysfs stubs for FIFOCFG and stashingClaudiu Manoil2014-02-181-30/+27
| | | | | | | | | | | | | | | | | | | | Removing the sysfs stubs for the Tx FIFOCFG and ATTRELI (stashing) config registers, as these registers may only be configured after a MAC reset, with the controller stopped (i.e. during hw init, at probe() time). The current sysfs stubs allow on-the-fly updates of these registers (the locking measures are useless and only add unecessary code). Changing these registers is discouraged. Only the default values will be used instead. Moreover, the stashing (ATTRELI) configuration options were effectively disabled (didn't get to the hw anyway if changed) because the stashing device_flags (HAS_BD_STASHING|HAS_BUF_STASHING) were "accidentally" cleared during probe(). Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Cleanup/Fix gfar_probe and the hw init codeClaudiu Manoil2014-02-181-174/+157
| | | | | | | | | | | | | | | | | | | | | | | | | | Factor out gfar_hw_init() to contain all the controller hw initialization steps for a better control of register writes, and to significantly simplify the tangled code from gfar_probe(). This results in code size and stack usage reduction (besides code readability). Fix memory leak on device removal, by freeing the rx_/tx_queue structures. Replace custom bit swapping function with a library one (bitrev8). Move allocation of rx_/tx_queue struct arrays before the group structure init, because in order to assign Rx/Tx queues to groups we need to have the queues first. This also allows earlier bail out of gfar_probe(), in case the memory allocation fails. The flow control checks for maccfg1 were removed from gfar_probe(), since flow control is disabled at probe time (priv->rx_/tx_pause_en are 0). Redundant initializations (by 0) also removed. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: delete non-required instances of include <linux/init.h>Paul Gortmaker2014-01-161-1/+0
| | | | | | | | | | | | | None of these files are actually using any __init type directives and hence don't need to include <linux/init.h>. Most are just a left over from __devinit and __cpuinit removal, or simply due to code getting copied from one driver to the next. This covers everything under drivers/net except for wireless, which has been submitted separately. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Implement the SIOCGHWTSTAMP ioctlBen Hutchings2013-11-211-4/+18
| | | | | | This is untested. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds2013-11-131-49/+38
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: 1) The addition of nftables. No longer will we need protocol aware firewall filtering modules, it can all live in userspace. At the core of nftables is a, for lack of a better term, virtual machine that executes byte codes to inspect packet or metadata (arriving interface index, etc.) and make verdict decisions. Besides support for loading packet contents and comparing them, the interpreter supports lookups in various datastructures as fundamental operations. For example sets are supports, and therefore one could create a set of whitelist IP address entries which have ACCEPT verdicts attached to them, and use the appropriate byte codes to do such lookups. Since the interpreted code is composed in userspace, userspace can do things like optimize things before giving it to the kernel. Another major improvement is the capability of atomically updating portions of the ruleset. In the existing netfilter implementation, one has to update the entire rule set in order to make a change and this is very expensive. Userspace tools exist to create nftables rules using existing netfilter rule sets, but both kernel implementations will need to co-exist for quite some time as we transition from the old to the new stuff. Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have worked so hard on this. 2) Daniel Borkmann and Hannes Frederic Sowa made several improvements to our pseudo-random number generator, mostly used for things like UDP port randomization and netfitler, amongst other things. In particular the taus88 generater is updated to taus113, and test cases are added. 3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet and Yang Yingliang. 4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin Sujir. 5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet, Neal Cardwell, and Yuchung Cheng. 6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary control message data, much like other socket option attributes. From Francesco Fusco. 7) Allow applications to specify a cap on the rate computed automatically by the kernel for pacing flows, via a new SO_MAX_PACING_RATE socket option. From Eric Dumazet. 8) Make the initial autotuned send buffer sizing in TCP more closely reflect actual needs, from Eric Dumazet. 9) Currently early socket demux only happens for TCP sockets, but we can do it for connected UDP sockets too. Implementation from Shawn Bohrer. 10) Refactor inet socket demux with the goal of improving hash demux performance for listening sockets. With the main goals being able to use RCU lookups on even request sockets, and eliminating the listening lock contention. From Eric Dumazet. 11) The bonding layer has many demuxes in it's fast path, and an RCU conversion was started back in 3.11, several changes here extend the RCU usage to even more locations. From Ding Tianhong and Wang Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav Falico. 12) Allow stackability of segmentation offloads to, in particular, allow segmentation offloading over tunnels. From Eric Dumazet. 13) Significantly improve the handling of secret keys we input into the various hash functions in the inet hashtables, TCP fast open, as well as syncookies. From Hannes Frederic Sowa. The key fundamental operation is "net_get_random_once()" which uses static keys. Hannes even extended this to ipv4/ipv6 fragmentation handling and our generic flow dissector. 14) The generic driver layer takes care now to set the driver data to NULL on device removal, so it's no longer necessary for drivers to explicitly set it to NULL any more. Many drivers have been cleaned up in this way, from Jingoo Han. 15) Add a BPF based packet scheduler classifier, from Daniel Borkmann. 16) Improve CRC32 interfaces and generic SKB checksum iterators so that SCTP's checksumming can more cleanly be handled. Also from Daniel Borkmann. 17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces using the interface MTU value. This helps avoid PMTU attacks, particularly on DNS servers. From Hannes Frederic Sowa. 18) Use generic XPS for transmit queue steering rather than internal (re-)implementation in virtio-net. From Jason Wang. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits) random32: add test cases for taus113 implementation random32: upgrade taus88 generator to taus113 from errata paper random32: move rnd_state to linux/random.h random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized random32: add periodic reseeding random32: fix off-by-one in seeding requirement PHY: Add RTL8201CP phy_driver to realtek xtsonic: add missing platform_set_drvdata() in xtsonic_probe() macmace: add missing platform_set_drvdata() in mace_probe() ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe() ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh vlan: Implement vlan_dev_get_egress_qos_mask as an inline. ixgbe: add warning when max_vfs is out of range. igb: Update link modes display in ethtool netfilter: push reasm skb through instead of original frag skbs ip6_output: fragment outgoing reassembled skb properly MAINTAINERS: mv643xx_eth: take over maintainership from Lennart net_sched: tbf: support of 64bit rates ixgbe: deleting dfwd stations out of order can cause null ptr deref ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS ...
OpenPOWER on IntegriCloud