summaryrefslogtreecommitdiffstats
path: root/drivers/net/e1000e/ich8lan.c
Commit message (Collapse)AuthorAgeFilesLines
* intel: Move the Intel wired LAN driversJeff Kirsher2011-08-101-4111/+0
| | | | | | | Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and the necessary Kconfig and Makefile changes. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: remove unnecessary check for NULL pointerBruce Allan2011-08-041-2/+1
| | | | | | | | The array shadow_ram is never NULL. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* intel drivers: repair missing flush operationsJesse Brandeburg2011-08-041-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | after review of all intel drivers, found several instances where drivers had the incorrect pattern of: memory mapped write(); delay(); which should always be: memory mapped write(); write flush(); /* aka memory mapped read */ delay(); explanation: The reason for including the flush is that writes can be held (posted) in PCI/PCIe bridges, but the read always has to complete synchronously and therefore has to flush all pending writes to a device. If a write is held and followed by a delay, the delay means nothing because the write may not have reached hardware (maybe even not until the next read) Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: Clear host wakeup bit on 82577/8 without touching PHY page 800Bruce Allan2011-06-091-11/+13
| | | | | | | | | | | | | | | | | | | The Host Wakeup Active bit in the PHY Port General Configuration register (page 769 register 17) must be cleared after every PHY reset to prevent an unexpected wake signal from the PHY. Originally, this was accomplished by simply reading the PHY Wakeup Control register on page 800 which clears the Host Wakeup Active bit as a side-effect. Unfortunately, a hardware bug on the 82577 and 82578 PHY can cause unexpected behavior when registers on page 800 are accessed while in gigabit mode. This patch changes the remaining instances when the Host Wakeup Active bit needs to be cleared while possibly in gigabit mode by accessing the Port General Configuration register directly instead of accessing any register on page 800. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: access multiple PHY registers on same page at the same timeBruce Allan2011-06-091-19/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Doing a PHY page select can take a long time, relatively speaking. This can cause a significant delay when updating a number of PHY registers on the same page by unnecessarily setting the page for each PHY access. For example when going to Sx, all the PHY wakeup registers (WUC, RAR[], MTA[], SHRAR[], IP4AT[], IP6AT[], etc.) on 82577/8/9 need to be updated which takes a long time which can cause issues when suspending. This patch introduces new PHY ops function pointers to allow callers to set the page directly and do any number of PHY accesses on that page. This feature is currently only implemented for 82577, 82578 and 82579 PHYs for both the normally addressed registers as well as the special- case addressing of the PHY wakeup registers on page 800. For the latter registers, the existing function for accessing the wakeup registers has been divided up into three- 1) enable access to the wakeup register page, 2) perform the register access and 3) disable access to the wakeup register page. The two functions that enable/disable access to the wakeup register page are necessarily available to the caller so that the caller can restore the value of the Port Control (a.k.a. Wakeup Enable) register after the wakeup register accesses are done. All instances of writing to multiple PHY registers on the same page are updated to use this new method and to acquire any PHY locking mechanism before setting the page and performing the register accesses, and release the locking mechanism afterward. Some affiliated magic number cleanup is done as well. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: log when swflag is cleared unexpectedly on ICH/PCH devicesBruce Allan2011-06-091-3/+8
| | | | | | | | | | | | | | Since EXTCNF_CTRL.SWFLAG (used in the ownership arbitration of shared resources, e.g. the PHY shared between the s/w, f/w, and h/w clients) can be cleared by any of those clients, log a debug message when software attempts to clear it and it is already cleared unexpectedly. And since the swflag is cleared by a hardware reset, the driver does not need to do that, but the mutex acquired when the bit is set must still be cleared. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: 82579 intermittently disabled during S0->SxBruce Allan2011-06-091-13/+73
| | | | | | | | | | | | | | | | | | When repeatedly cycling Sx->S0 states with the network cable unplugged, the 82579 PHY may not initialize as expected and may require a full power cycle to recover functionality to the device. Workaround this by testing access of the PHY registers after resuming; if that returns unexpected results toggle the LANPHYPC signal to power cycle the PHY. This is implemented in the new function e1000_resume_workarounds_pchlan() which calls another new function, e1000_toggle_lanphypc_value_ich8lan(), which has been created to reduce code duplication (same functionality required by a previous workaround). Also, e1000e_disable_gig_wol_ich8lan is now e1000_suspend_workarounds_ich8lan to better reflect what it does. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: implement ethtool set_phys_idBruce Allan2011-04-271-0/+4
| | | | | | | | | | | | | | | | | | Based on a patch from Stephen Hemminger <shemminger@vyatta.com>. The new ethtool set_phys_id takes over controlling the LED for identifying boards. This fixes the lockout during that period. For this device lots of extra infrastructure can also be removed by using set_phys_id. v2: - return blink frequency for parts that do not support blink in h/w - add blink_led function pointers for devices that do support blink in h/w to cleanup the test for this functionality Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Cc: Stephen Hemminger <shemminger@vyatta.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: convert short duration msleep() to usleep_range()Bruce Allan2011-04-131-6/+6
| | | | | | | | | | | | | With durations less than 20ms, the jiffies or legacy timer backed msleep() may sleep ~20ms which might not be what the caller expects. Instead, it is recommended to use the hrtimers backed usleep_range(). For more, see Documentation/timers/timers-howto.txt. Issues reported by checkpatch. In addition, remove unnecessary sleep in e1000e_write_nvm_spi(). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: disable jumbo frames on 82579 when MACsec enabled in EEPROMBruce Allan2011-03-111-1/+7
| | | | | | | | | | If/when an OEM enables MACsec in the 82579 EEPROM, disable jumbo frames support in the driver due to an interoperability issue in hardware that prevents jumbo packets from being transmitted or received. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: do not toggle LANPHYPC value bit when PHY reset is blockedBruce Allan2011-03-111-4/+4
| | | | | | | | | | | | When PHY reset is intentionally blocked on 82577/8/9, do not toggle the LANPHYPC value bit (essentially performing a hard power reset of the device) otherwise the PHY can be put into an unknown state. Cleanup whitespace in the same function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: extend EEE LPI timer to prevent dropped linkBruce Allan2011-03-111-5/+24
| | | | | | | | | | The link can be unexpectedly dropped when the timer for entering EEE low- power-idle quiet state expires too soon. The timer needs to be extended from 196usec to 200usec after every LCD (PHY) reset to prevent this from happening. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: reduce scope of some variables, remove unnecessary onesBruce Allan2011-01-241-1/+2
| | | | | | | | | Static analysis of the driver code found some variables for which the scope can be reduced, or remove the variable altogether. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds2011-01-141-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits) GRETH: resolve SMP issues and other problems GRETH: handle frame error interrupts GRETH: avoid writing bad speed/duplex when setting transfer mode GRETH: fixed skb buffer memory leak on frame errors GRETH: GBit transmit descriptor handling optimization GRETH: fix opening/closing GRETH: added raw AMBA vendor/device number to match against. cassini: Fix build bustage on x86. e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs e1000e: update Copyright for 2011 e1000: Avoid unhandled IRQ r8169: keep firmware in memory. netdev: tilepro: Use is_unicast_ether_addr helper etherdevice.h: Add is_unicast_ether_addr function ks8695net: Use default implementation of ethtool_ops::get_link ks8695net: Disable non-working ethtool operations USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable. vxge: Remember to release firmware after upgrading firmware netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr ipsec: update MAX_AH_AUTH_LEN to support sha512 ...
| * e1000e: update Copyright for 2011Bruce Allan2011-01-141-1/+1
| | | | | | | | | | | | Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | Merge branch 'for-next' of ↵Linus Torvalds2011-01-131-1/+1
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits) Documentation/trace/events.txt: Remove obsolete sched_signal_send. writeback: fix global_dirty_limits comment runtime -> real-time ppc: fix comment typo singal -> signal drivers: fix comment typo diable -> disable. m68k: fix comment typo diable -> disable. wireless: comment typo fix diable -> disable. media: comment typo fix diable -> disable. remove doc for obsolete dynamic-printk kernel-parameter remove extraneous 'is' from Documentation/iostats.txt Fix spelling milisec -> ms in snd_ps3 module parameter description Fix spelling mistakes in comments Revert conflicting V4L changes i7core_edac: fix typos in comments mm/rmap.c: fix comment sound, ca0106: Fix assignment to 'channel'. hrtimer: fix a typo in comment init/Kconfig: fix typo anon_inodes: fix wrong function name in comment fix comment typos concerning "consistent" poll: fix a typo in comment ... Fix up trivial conflicts in: - drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c) - fs/ext4/ext4.h Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
| * tree-wide: fix comment/printk typosUwe Kleine-König2010-11-011-1/+1
| | | | | | | | | | | | | | | | | | | | "gadget", "through", "command", "maintain", "maintain", "controller", "address", "between", "initiali[zs]e", "instead", "function", "select", "already", "equal", "access", "management", "hierarchy", "registration", "interest", "relative", "memory", "offset", "already", Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* | e1000e: use either_crc_le() rather than re-write itBruce Allan2011-01-091-18/+1
| | | | | | | | | | | | | | | | | | | | For the 82579 jumbo frame workaround, there is no need to re-write the CRC calculation functionality already found in the kernel's ether_crc_le(). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | e1000e: convert calls of ops.[read|write]_reg to e1e_[r|w]phyBruce Allan2011-01-091-29/+25
| | | | | | | | | | | | | | | | | | | | | | Cleans up the code a bit by using the driver-specific e1e_rphy and e1e_wphy macros instead of the full function pointer variants. Fix a couple whitespace issue with two already existing calls to e1e_wphy. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | e1000e: cleanup variables set but not usedBruce Allan2011-01-091-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | The ICR register is clear on read and we don't care what the returned value is when resetting the hardware so the icr variable(s) can be removed. We should not ignore the return from e1000_lv_jumbo_workaround_ich8lan() and from e1000_get_phy_id_82571() (dump a debug message when it fails and when an unknown Phy id is returned). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | e1000e: checkpatch warnings - bracesBruce Allan2010-12-241-3/+2
| | | | | | | | | | | | | | | | | | WARNING: braces {} are not necessary for any arm of this statement WARNING: braces {} are not necessary for single statement blocks Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | e1000e: 82579 PHY incorrectly identified during initBruce Allan2010-12-101-5/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | During init, reading the 2 PHY ID registers back-to-back in the default fast mode could return invalid data (all F's) and in slow mode could return data to the second read the data from the first read. To resolve the issue in fast mode, set to slow mode before any PHY accesses; to resolve the issue in slow mode, put in a delay for every 82579 PHY access. Since this PHY is currently only paired with the pch2lan MAC and the PHY type is not known before the first PHY access which can fail this way, check for this based on MAC-type. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | e1000e: 82577/8/9 mis-configured OEM bits during S0->SxBruce Allan2010-12-101-1/+1
|/ | | | | | | | | The LPLU (Low Power Link Up) and Gigabit Disable bits (a.k.a. OEM bits) were being configured incorrectly when device goes to D3 state. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: 82579 performance improvementsBruce Allan2010-09-301-1/+1
| | | | | | | | | | | | The initial support for 82579 was tuned poorly for performance. Adjust the packet buffer allocation appropriately for both standard and jumbo frames; and for jumbo frames increase the receive descriptor pre-fetch, disable adaptive interrupt moderation and set the DMA latency tolerance. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: 82579 do not gate auto config of PHY by hardware during nominal useBruce Allan2010-09-221-9/+68
| | | | | | | | | | | | | | | | | For non-managed versions of 82579, set the bit that prevents the hardware from automatically configuring the PHY after resets only when the driver performs a reset, clear the bit after resets. This is so the hardware can configure the PHY automatically when the part is reset in a manner that is not controlled by the driver (e.g. in a virtual environment via PCI FLR) otherwise the PHY will be mis-configured causing issues such as failing to link at 1000Mbps. For managed versions of 82579, keep the previous behavior since the manageability firmware will handle the PHY configuration. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: 82579 jumbo frame workaround causing CRC errorsBruce Allan2010-09-221-11/+1
| | | | | | | | | | | | | | | The subject workaround was causing CRC errors due to writing the wrong register with updates of the RCTL register. It was also found that the workaround function which modifies the RCTL register was being called in the middle of a read-modify-write operation of the RCTL register, so the function call has been moved appropriately. Lastly, jumbo frames must not be allowed when CRC stripping is disabled by a module parameter because the workaround requires the CRC be stripped. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: 82579 unaccounted missed packetsBruce Allan2010-09-221-0/+48
| | | | | | | | | | | | | On 82579, there is a hardware bug that can cause received packets to not get transferred from the PHY to the MAC due to K1 (a power saving feature of the PHY-MAC interconnect similar to ASPM L1). Since the MAC controls the accounting of missed packets, these will go unnoticed. Workaround the issue by setting the K1 beacon duration according to the link speed. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: 82566DC fails to get linkBruce Allan2010-09-221-2/+5
| | | | | | | | | | | | | | | | Two recent patches to cleanup the reset[1] and initial PHY configuration[2] code paths for ICH/PCH devices inadvertently left out a 10msec delay and device ID check respectively which are necessary for the 82566DC (device id 0x104b) to be configured properly, otherwise it will not get link. [1] commit e98cac447cc1cc418dff1d610a5c79c4f2bdec7f [2] commit 3f0c16e84438d657d29446f85fe375794a93f159 CC: stable@kernel.org Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: 82579 SMBus address and LEDs incorrect after device resetBruce Allan2010-09-221-3/+3
| | | | | | | | | | | | | Since the hardware is prevented from performing automatic PHY configuration (the driver does it instead), the OEM_WRITE_ENABLE bit in the EXTCNF_CTRL register will not get cleared preventing the SMBus address and the LED configuration to be written to the PHY registers. On 82579, do not check the OEM_WRITE_ENABLE bit. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: 82577/8/9 issues with device in SxBruce Allan2010-09-221-8/+39
| | | | | | | | | | | | | | | When going to Sx, disable gigabit in PHY (e1000_oem_bits_config_ich8lan) in addition to the MAC before configuring PHY wakeup otherwise the PHY configuration writes might be missed. Also write the LED configuration and SMBus address to the PHY registers (e1000_oem_bits_config_ich8lan and e1000_write_smbus_addr, respectively). The reset is no longer needed since re-auto-negotiation is forced in e1000_oem_bits_config_ich8lan and leaving it in causes issues with auto-negotiating the link. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: disable EEE support by defaultBruce Allan2010-06-291-0/+4
| | | | | | | | | | | Based on community feedback, EEE should be disabled by default until the IEEE802.3az specification has been finalized. Cc: bhutchings@solarflare.com Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: disable gig speed when in S0->Sx transitionBruce Allan2010-06-231-14/+5
| | | | | | | | | | Most of this workaround is necessary for all ICHx/PCH parts so one of the two MAC-type checks can be removed. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: update copyright informationBruce Allan2010-06-181-1/+1
| | | | | | | Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: enable support for EEE on 82579Bruce Allan2010-06-181-1/+40
| | | | | | | | | | | This patch enables IEEE802.3az (a.k.a. Energy Efficient Ethernet) on the new 82579 LOMs. An optional module parameter is provided to disable the feature if desired. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: initial support for 82579 LOMsBruce Allan2010-06-181-17/+311
| | | | | | | Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: fix check for manageability on ICHx/PCHBruce Allan2010-06-181-4/+27
| | | | | | | | | | | | Do not check for all the bits in E1000_FWSM_MODE_MASK when checking for manageability on 82577/82578; only check if iAMT is enabled. Both of the manageability checks (for 82577/82578 and ICHx) must check the firmware valid bit too since the other bits are only valid when the latter is set. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: separate out PHY statistics register updatesBruce Allan2010-06-181-0/+1
| | | | | | | | | | | | The 82577/82578 parts have half-duplex statistics in PHY registers. These need only be read when in half-duplex and should all be read at once rather than one at a time to prevent excessive cycles of acquiring/releasing the PHY semaphore. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: cleanup e1000_sw_lcd_config_ich8lan()Bruce Allan2010-06-181-13/+19
| | | | | | | | | | Do not acquire and release the PHY unnecessarily for parts that return from this workaround without actually accessing the PHY registers. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: Remove unnecessary returns from void function()sJoe Perches2010-05-141-10/+0
| | | | | | | | | | | | | | | | | | | | | | This patch removes from drivers/net/ all the unnecessary return; statements that precede the last closing brace of void functions. It does not remove the returns that are immediately preceded by a label as gcc doesn't like that. It also does not remove null void functions with return. Done via: $ grep -rP --include=*.[ch] -l "return;\n}" net/ | \ xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }' with some cleanups by hand. Compile tested x86 allmodconfig only. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: Fix/cleanup PHY reset code for ICHx/PCHxBruce Allan2010-05-121-74/+75
| | | | | | | | | | | | | | | | | | | | | | | | | | i) Fixes a bug where e1000_sw_lcd_config_ich8lan() was calling e1000_lan_init_done_ich8lan() to poll the STATUS.LAN_INIT_DONE bit to make sure the MAC had completed the PHY configuration. However, e1000_lan_init_done_ich8lan() had already been called in one of the two places where PHY reset occurs for ICHx/PCHx parts, which caused the second call to busy-wait for 150 msec because the LAN_INIT_DONE bit had already been checked and cleared. ii) Cleanup the two separate PHY reset code paths, i.e. the full-chip reset in e1000_reset_hw_ich8lan() and the PHY-only reset in e1000_phy_hw_reset_ich8lan(). There was duplicate code in both paths to be performed post-reset that are now combined into one new function - e1000_post_phy_reset_ich8lan(). This cleanup also included moving the clearing of the PHY Reset Asserted bit in the STATUS register (now done for all ICH/PCH parts) and the check for the indication from h/w that basic configuration has completed back to where it previously was in e1000_get_cfg_done_ich8lan(). iii) Corrected a few comments Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: move settting of flow control refresh timer to link setup codeBruce Allan2010-05-121-0/+2
| | | | | | | | | | The flow control refresh timer value needs to be saved off so that it can be programmed into the approrpiate register when applicable but without a reset, e.g. when changing flow control parameters via ethtool. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: fix checks for manageability enabled and management pass-throughBruce Allan2010-05-121-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | The mac->arc_subsystem was being incorrectly used to flag whether or not manageability was enabled when it should only be used to state whether the ARC (Host interface) subsystem is available on a particular MAC _and_ only valid when any manageability is enabled. The ARC subsystem is currently only available on 80003es2lan and 82573 parts supported by the driver. A new flag, has_fwsm, is introduced to be used when checking if manageability is enabled but only on parts that acutally have an FWSM register. While the above parts have an FWSM register, there are other parts that have FWSM but do not have support for the ARC subsystem, namely 82571/2 and ICHx/PCH. And then there are parts that have manageability, but do not have either FWSM register or support for the ARC subsystem - these are 82574 and 82583. For 80003es2lan, 82571/2/3 and ICH/PCH parts, this patch makes no functional changes, it only corrects the usage of the manageability flags. For 82574 and 82583, it fixes the incorrect accesses of the non-existent FWSM register and ARC subsystem as well as corrects the check for management pass-through. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: Incorrect function pointer set for force_speed_duplex on 82577Bruce Allan2010-05-121-0/+1
| | | | | | | | | | | | | The force_speed_duplex function pointer was incorrectly set. Instead of calling the 82577-specific version it was calling the m88 version which, among other incorrect things, reset the PHY causing autonegotiation to be re-enabled in the PHY resulting in the link defaulting to half-duplex. The 82577-specific force_speed_duplex function also had an issue where it disabled Auto-MDI-X which caused the link to not come up. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: Cleanup e1000_sw_lcd_config_ich8lan()Bruce Allan2010-05-121-77/+75
| | | | | | | | | | | | | | After every reset all ICH/PCH parts call this function which acquires the swflag, performs a workaround on applicable parts and releases the swflag. There is no reason for parts for which this workaround is not applicable to acquire and release the swflag so the function should just return without doing anything for these parts. This also provides for the indentation of most of the function contents to be shifted left cleaning up the code. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: cleanup multiple common exit pointsBruce Allan2010-05-121-24/+17
| | | | | | | | ...in e1000_update_nvm_checksum_ich8lan(). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: Reset 82577/82578 PHY before first PHY register readBruce Allan2010-05-061-0/+10
| | | | | | | | | | Reset the PHY before first accessing it. Doing so, ensure that the PHY is in a known good state before we read/write PHY registers. This fixes a driver probe failure. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: reset MAC-PHY interconnect on 82577/82578 during Sx->S0Bruce Allan2010-05-061-0/+20
| | | | | | | | | | | | During Sx->S0 transitions, the interconnect between the MAC and PHY on 82577/82578 can remain in SMBus mode instead of transitioning to the PCIe-like mode required during normal operation. Toggling the LANPHYPC Value bit essentially resets the interconnect forcing it to the correct mode. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: typo correctionsJoe Perches2010-03-301-3/+3
| | | | | | | | | | | | | Here are the other miscellaneous corrections done by an earlier larger suggested patch now made unnecessary by a less invasive change. Correct a few missing newlines from logging messages and a typo fix. Fix speed/duplex logging message. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: fix packet corruption and tx hang during NFSv2Jesse Brandeburg2010-03-051-0/+10
| | | | | | | | | | | | | | when receiving a particular type of NFS v2 UDP traffic, the hardware could DMA some bad data and then hang, possibly corrupting memory. Disable the NFS parsing in this hardware, verified to fix the bug. Originally reported and reproduced by RedHat's Neil Horman CC: nhorman@tuxdriver.com Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2010-01-231-5/+71
|\ | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
OpenPOWER on IntegriCloud