| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The previous change 3973c526ae9c (net: can: c_can: Disable pins when CAN
interface is down) causes a slight glitch on the pinctrl settings when used.
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
the device core will automatically set the default pins. This causes the pins
to be momentarily set to the default and then to the sleep state in
register_c_can_dev(). By adding an optional "enable" state, boards can set the
default pin state to be disabled and avoid the glitch when the switch from
default to sleep first occurs. If the "enable" state is not available
c_can_pinctrl_select_state() falls back to using the "default" pinctrl state.
[Roger Q] - Forward port to v4.2 and use pinctrl_get_select().
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Put controller into init mode in network stop to end pending transmissions. The
issue is observed in cases when transmitted frame is not acked.
Signed-off-by: Viktor Babrian <babrian.viktor@renyi.mta.hu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
use of regmap_read() and regmap_write() in c_can_hw_raminit_syscon()
is not safe as the RAMINIT register can be shared between different drivers
at least for TI SoCs.
To make the modification atomic we switch to using regmap_update_bits().
regmap_update_bits() skips writing to the register if it's read content is the
same as what is going to be written. This causes an issue for us when we
need to clear the DONE bit with the initial condition START:0, DONE:1 as
DONE bit must be written with 1 to clear it.
So we defer the clearing of DONE bit to later when we set the START bit.
There we are sure that START bit is changed from 0 to 1 so the write of
1 to already set DONE bit will happen.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|/
|
|
|
|
|
|
|
|
|
|
|
| |
In order to be able to move the stats increment from can_bus_off() into
can_change_state(), the increment had to be moved back into code that was using
can_bus_off() but not can_change_state().
As a side-effect, this patch fixes the following bugs:
* Redundant call to can_bus_off() in c_can.
* Bus-off counted twice in xilinx_can.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
| |
| |
| |
| |
| |
| |
| | |
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
AM3352 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for am3352 DCAN.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| | |
DRA7 SoC has 2 CAN IPs. Provide compatible IDs and RAMINIT
register data for both.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
DRA7 CAN IP suffers from a problem which causes it to be prevented
from fully turning OFF (i.e. stuck in transition) if the module was
disabled while there was traffic on the CAN_RX line.
To work around this issue we select the SLEEP pin state by default
on probe and use the DEFAULT pin state on CAN up and back to the
SLEEP pin state on CAN down.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Some SoCs e.g. (TI DRA7xx) need a START pulse to start the
RAMINIT sequence i.e. START bit must be set and cleared before
checking for the DONE bit status.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Some TI SoCs like DRA7 have a RAMINIT register specification
different from the other AMxx SoCs and as expected by the
existing driver.
To add more insanity, this register is shared with other
IPs like DSS, PCIe and PWM.
Provides a more generic mechanism to specify the RAMINIT
register location and START/DONE bit position and use the
syscon/regmap framework to access the register.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Some platforms (e.g. TI) need special RAMINIT register handling.
Provide a way to store RAMINIT register description in driver data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We want to have more data than just can_dev_id to be present
in the driver data e.g. TI platforms need RAMINIT register
description. Introduce the c_can_driver_data structure and move
the can_dev_id into it.
Tidy up the way it is used on probe().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|/
|
|
|
|
|
|
|
|
| |
TI's RAMINIT DONE mechanism is buggy on AM43xx SoC and may not always
be set after the START bit is set. Although it seems to work fine even
in that case. So add a timeout mechanism to c_can_hw_raminit_wait_ti().
Don't bail out in that failure case but just print an error message.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pass the correct 'mask' and 'value' bits to c_can_hw_raminit_wait_ti(). They
seem to have been swapped in the usage instances.
Reported-by: Jay Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|\ \
| |/
| |
| |
| |
| |
| | |
Pulling to get some TIPC fixes that a net-next series depends
upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
devm_ioremap() returns NULL on error, not an ERR_PTR().
Fixes: 33cf75656923 ('can: c_can_platform: Fix raminit, use devm_ioremap() instead of devm_ioremap_resource()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|/
|
|
|
|
|
|
| |
No need to manually copy debug settings into subdir Makefiles. kbuild
has a mechanism for inheriting, so let's use it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|\
| |
| |
| | |
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
devm_ioremap_resource()
The raminit register is shared register for both can0 and can1. Since commit:
32766ff net: can: Convert to use devm_ioremap_resource
devm_ioremap_resource() is used to map raminit register. When using both
interfaces the mapping for the can1 interface fails, leading to a non
functional can interface.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|/
|
|
|
|
|
| |
This patch uses devm_* APIs as they are device managed and make code simpler.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In 2b9aecdce2 ("can: c_can: Disable rx split as workaround") a new Kconfig
option was introduced as a workaround. The tests performed by Alexander Stein
confirmed this option to be obsolete with all the other cleanups and fixes
that had been discussed that time:
http://marc.info/?l=linux-can&m=139746476821294&w=2
Both (author and tester) agreed to remove this Kconfig option again:
http://marc.info/?l=linux-can&m=139883820714229&w=2
As some more cleanups took place since then a simple revert is not possible.
This patch removes the entire option as it would behave when disabled.
Further beautification’s can be done later.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Non-TI chips (including socfpga) needs different raminit sequence. Implement
it.
Tested-by: Thor Thayer <tthayer@altera.com>
Signed-off-by: Thor Thayer <tthayer@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add helpers for 32-bit accesses and replace open-coded 32-bit access
with calls to helpers. Minimum changes are done to the pci case, as I
don't have access to that hardware.
Tested-by: Thor Thayer <tthayer@altera.com>
Signed-off-by: Thor Thayer <tthayer@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch makes the {read,write}_reg functions const, this is a preparation to
make use of {read,write}_reg in the hwinit callback.
Signed-off-by: Thor Thayer <tthayer@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|\ \
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Coverity complains that c_can_pci_probe() calls pci_enable_msi() without
checking the result:
CID 712278 (#1 of 1): Unchecked return value (CHECKED_RETURN) 3. check_return:
Calling pci_enable_msi_block without checking return value (as is done
elsewhere 88 out of 105 times).
88 pci_enable_msi(pdev);
This is CID 712278.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit 6439fbce1075 (can: c_can: fix error checking of priv->instance in
probe()) found the warning but applied a suboptimal solution. Since, both
pdev->id and of_alias_get_id() return integers, it makes sense to convert the
variable to an integer and avoid the cast.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
It's suffcient to kill the TXIE bit in the message control register
even if the documentation of C and D CAN says that it's not allowed to
do that while MSGVAL is set. Reality tells a different story and this
change gives us another 2% of CPU back for not waiting on I/O.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Mark suggested to use one IF for the softirq and the other for the
xmit function to avoid the xmit lock.
That requires to write the frame into the interface first, then handle
the echo skb and store the dlc before committing the TX request to the
message ram.
We use an atomic to handle the active buffers instead of reading the
MSGVAL register as thats way faster especially on PCH/x86.
Suggested-by: Mark <mark5@del-llc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Instead of obfuscating the code by artificial 16 bit splits use the
proper 32 bit assignments and split the result when writing to the
interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Remove the MASK from the TX transfer side.
Make the code readable and get rid of the annoying IFX_WRITE_XXX_16BIT
macros which are just obfuscating the code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Sigh!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| | |
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| | |
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| | |
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| | |
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Alexander reported that the new optimized handling of the RX fifo
causes random packet loss on Intel PCH C_CAN hardware.
After a few fruitless debugging sessions I got hold of a PCH (eg20t)
afflicted system. That machine does not have the CAN interface wired
up, but it was possible to reproduce the issue with the HW loopback
mode.
As Alexander observed correctly, clearing the NewDat flag along with
reading out the message buffer causes that issue on C_CAN, while D_CAN
handles that correctly.
Instead of restoring the original message buffer handling horror the
following workaround solves the issue:
transfer buffer to IF without clearing the NewDat
handle the message
clear NewDat bit
That's similar to the original code but conditional for C_CAN.
I really wonder why all user manuals (C_CAN, Intel PCH and some more)
recommend to clear the NewDat bit right away. The knows it all Oracle
operated by Gurgle does not unearth any useful information either. I
simply cannot believe that we are the first to uncover that HW issue.
Reported-and-tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The RX buffer split causes packet loss in the hardware:
What happens is:
RX Packet 1 --> message buffer 1 (newdat bit is not cleared)
RX Packet 2 --> message buffer 2 (newdat bit is not cleared)
RX Packet 3 --> message buffer 3 (newdat bit is not cleared)
RX Packet 4 --> message buffer 4 (newdat bit is not cleared)
RX Packet 5 --> message buffer 5 (newdat bit is not cleared)
RX Packet 6 --> message buffer 6 (newdat bit is not cleared)
RX Packet 7 --> message buffer 7 (newdat bit is not cleared)
RX Packet 8 --> message buffer 8 (newdat bit is not cleared)
Clear newdat bit in message buffer 1
Clear newdat bit in message buffer 2
Clear newdat bit in message buffer 3
Clear newdat bit in message buffer 4
Clear newdat bit in message buffer 5
Clear newdat bit in message buffer 6
Clear newdat bit in message buffer 7
Clear newdat bit in message buffer 8
Now if during that clearing of newdat bits, a new message comes in,
the HW gets confused and drops it.
It does not matter how many of them you clear. I put a delay between
clear of buffer 1 and buffer 2 which was long enough that the message
should have been queued either in buffer 1 or buffer 9. But it did not
show up anywhere. The next message ended up in buffer 1. So the
hardware lost a packet of course without telling it via one of the
error handlers.
That does not happen on all clear newdat bit events. I see one of 10k
packets dropped in the scenario which allows us to reproduce. But the
trace looks always the same.
Not splitting the RX Buffer avoids the packet loss but can cause
reordering. It's hard to trigger, but it CAN happen.
With that mode we use the HW as it was probably designed for. We read
from the buffer 1 upwards and clear the buffer as we get the
message. That's how all microcontrollers use it. So I assume that the
way we handle the buffers was never really tested. According to the
public documentation it should just work :)
Let the user decide which evil is the lesser one.
[ Oliver Hartkopp: Provided a sane config option and help text and
made me switch to favour potential and unlikely reordering over
packet loss ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The driver handles pointlessly TWO interrupts per packet. The reason
is that it enables the status interrupt which fires for each rx and tx
packet and it enables the per message object interrupts as well.
The status interrupt merily acks or in case of D_CAN ignores the TX/RX
state and then the message object interrupt fires.
The message objects interrupts are only useful if all message objects
have hardware filters activated.
But we don't have that and its not simple to implement in that driver
without rewriting it completely.
So we can ditch the message object interrupts and handle the RX/TX
right away from the status interrupt. Instead of TWO we handle ONE.
Note: We must keep the TXIE/RXIE bits in the message buffers because
the status interrupt alone is not reliable enough in corner cases.
If we ever have the need for HW filtering, then this code needs a
complete overhaul and we can think about it then. For now we prefer a
lower interrupt load.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On D_CAN the RXOK, TXOK and LEC bits are cleared/set on read of the
status register. No need to update them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Instead of writing to the message object we can simply clear the
NewDat bit with the get method.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
If the allocation of the error skb fails, we still want to see the
error statistics.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Reading the LEC type with
return (mode & ENABLED) && (status & LEC_MASK);
is not guaranteed to return (status & LEC_MASK) if the enabled bit in
mode is set. It's guaranteed to return 0 or !=0.
Remove the inline function and call unconditionally into the
berr_handling code and return early when the reporting is disabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
If the allocation of an error skb fails, the state change handling
returns w/o doing any work. That leaves the interface in a wreckaged
state as the internal status is wrong.
Split the interface handling and the skb handling.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|