| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Prevent packets duplication for frames targeting FCoE L2 ring:
packets were arriving to stack from both L2 RSS and from FCoE
L2 in a promiscuous mode.
Configure FCoE L2 ring to DROP_ALL rx mode, when interface is
configured to PROMISC, and to accept only unicast frames, when
interface is configured to ALL_MULTI.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
The chip was erroneously configured to accept all multicast frames
in a normal (none-promisc) rx mode both on the RSS and on the FCoE L2 rings
when in an NPAR mode. This caused packet duplication for every received multicast
frame in this mode.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
Update bnx2x version to 1.62.00-5
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
All functions on a port should be set to take the MDC/MDIO lock to avoid contention on the bus
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
Fix link on BCM57712 + BCM8073 when port swap is enabled. Common PHY reset was done on the wrong port.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
Fix blink rate of activity LED of the BCM84823 on 10G link
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
A rare link issue with the BCM8073 PHY may occur due to setting XAUI low power mode, while the PHY microcode already does that.
The fix is not to set set XAUI low power mode for this PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
sctp: user perfect name for Delayed SACK Timer option
net: fix can_checksum_protocol() arguments swap
Revert "netlink: test for all flags of the NLM_F_DUMP composite"
gianfar: Fix misleading indentation in startup_gfar()
net/irda/sh_irda: return to RX mode when TX error
net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.
USB CDC NCM: tx_fixup() race condition fix
ns83820: Avoid bad pointer deref in ns83820_init_one().
ipv6: Silence privacy extensions initialization
bnx2x: Update bnx2x version to 1.62.00-4
bnx2x: Fix AER setting for BCM57712
bnx2x: Fix BCM84823 LED behavior
bnx2x: Mark full duplex on some external PHYs
bnx2x: Fix BCM8073/BCM8727 microcode loading
bnx2x: LED fix for BCM8727 over BCM57712
bnx2x: Common init will be executed only once after POR
bnx2x: Swap BCM8073 PHY polarity if required
iwlwifi: fix valid chain reading from EEPROM
ath5k: fix locking in tx_complete_poll_work
ath9k_hw: do PA offset calibration only on longcal interval
...
|
| |
| |
| |
| |
| |
| |
| |
| | |
Update bnx2x version to 1.62.00-4
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Fix AER settings for BCM57712 to allow accessing all device addresses range in CL45 MDC/MDIO
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Fix BCM84823 LED behavior which may show on some systems
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Device may show incorrect duplex mode for devices with external PHY
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Improve microcode loading verification before proceeding to next stage
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| | |
LED on BCM57712+BCM8727 systems requires different settings
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Common init used to be called by the driver when the first port comes up, mainly to reset and reload external PHY microcode.
However, in case management driver is active on the other port, traffic would halted. So limit the common init to be done only once after POR.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Enable controlling BCM8073 PN polarity swap through nvm configuration, which is required in certain systems
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \
| |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
Documentation/trace/events.txt: Remove obsolete sched_signal_send.
writeback: fix global_dirty_limits comment runtime -> real-time
ppc: fix comment typo singal -> signal
drivers: fix comment typo diable -> disable.
m68k: fix comment typo diable -> disable.
wireless: comment typo fix diable -> disable.
media: comment typo fix diable -> disable.
remove doc for obsolete dynamic-printk kernel-parameter
remove extraneous 'is' from Documentation/iostats.txt
Fix spelling milisec -> ms in snd_ps3 module parameter description
Fix spelling mistakes in comments
Revert conflicting V4L changes
i7core_edac: fix typos in comments
mm/rmap.c: fix comment
sound, ca0106: Fix assignment to 'channel'.
hrtimer: fix a typo in comment
init/Kconfig: fix typo
anon_inodes: fix wrong function name in comment
fix comment typos concerning "consistent"
poll: fix a typo in comment
...
Fix up trivial conflicts in:
- drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
- fs/ext4/ext4.h
Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
|
| |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
|
| | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
bnx2x_src_init_t2() is used only when BCM_CNIC is defined.
So, to avoid a compilation warning, we won't define it unless
BCM_CNIC is defined.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Make the LSO code work on BE platforms: parsing_data field of
a parsing BD (PBD) for 57712 was improperly composed which made FW read wrong
values for TCP header's length and offset and, as a result, the corresponding
PCI device was performing bad DMA reads triggering EEH.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fix the race on bp->stats_pending between the timer and a LINK_UP event
handler.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Move to D0 before clearing MSI/MSI-X configuration. Otherwise MSI/MSI-X
won't be cleared.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fixes in registers dump:
- Properly calculate dump length for 57712.
- Prevent HW blocks parity attentions when dumping registers in order to
prevent false parity errors handling.
- Update the bnx2x_dump.h file: old one had a few bugs that could cause
fatal HW error as a result of a registers dump.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Don't prevent RSS configuration in INT#x and MSI interrupt modes. Otherwise
Rx hash key won't be available.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Adding dcbnl implementation to bnx2x allowing users to manage the
embedded DCBX engine.
This patch is dependent on the following patches:
[net-next-2.6 PATCH 1/3] dcbnl: add support for ieee8021Qaz attributes
[net-next-2.6 PATCH 2/3] dcbnl: add appliction tlv handlers
[net-next-2.6 PATCH 3/3] net_dcb: add application notifiers
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \ \ |
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>
|
|/ / /
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
We dereferenced params on the line before so it's too late to check if
params is NULL. In fact, params can never be NULL and strict_cos is
either 0 or 1 so that part of the check is bogus too. Let's remove it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Includes FCoE releated fixes in FW flows
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add appropriate HW DCB/PFC configuration
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Adding DCB initialization and handling on 57712 FW/HW
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This callback required to allow FCoE traffic to be
sent on separate priority queue from other L2 traffic,
which is managed by PFC in HW.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Includes new driver structures and FW/HW configuration for FCoE ring
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
bnx2x_src_init_t2() is used only when BCM_CNIC is defined.
So, to avoid a compilation warning, we won't define it unless
BCM_CNIC is defined.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Make the LSO code work on BE platforms: parsing_data field of
a parsing BD (PBD) for 57712 was improperly composed which made FW read wrong
values for TCP header's length and offset and, as a result, the corresponding
PCI device was performing bad DMA reads triggering EEH.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
NETIF_F_HW_CSUM is a superset of NETIF_F_IP_CSUM+NETIF_F_IPV6_CSUM, but
some drivers miss the difference. Fix this and also fix UFO dependency
on checksumming offload as it makes the same mistake in assumptions.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
NIC partitioning is another flavor of multi function - having few
PCI functions share the same physical port. Unlike the currently
supported mode of multi-function which depends on the switch
configuration and uses outer-VLAN, the NPAR mode is switch independent
and uses the MAC addresses to distribute incoming packets to the different
functions. This patch adds the specific HW setting of the NPAR mode
and some distinctions between switch dependent (SD) and
switch independent (SI) multi-function (MF) modes where the configuration
is not the same.
Advance driver version to 1.60.00-6
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
register_netdev()
Move the interrupt mode configuration and NAPIs adding before a
register_netdev() call to prevent netdev->open() from running
before these functions are done.
Advance a driver version number.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reported-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
According to Eric's suggestion:
Disable local BHes to prevent a dead-lock situation between sch_direct_xmit()
(Soft_IRQ context) and bnx2x_tx_int (called by bnx2x_run_loopback() - syscall
context), as both are taking a netif_tx_lock().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \ \
| | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | | |
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/bonding/bond_main.c
net/core/net-sysfs.c
net/ipv6/addrconf.c
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
bnx2x_init_one() should return negative value on error.
By mistake it returns ENODEV instead of -ENODEV.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/ /
| |
| |
| |
| | |
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently the skb->protocol field is used to setup checksum
offloading on transmit for the correct protocol. However, if
vlan offloading is disabled or otherwise not used, the protocol
field will be ETH_P_8021Q, not the actual protocol. This will
cause the checksum to be not computed correctly, even though the
hardware is capable of looking inside vlan tags. Instead,
look inside the header if necessary to determine the correct
protocol type.
To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.
Signed-off-by: Hao Zheng <hzheng@nicira.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Update bnx2x version number.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|