| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
| |
'of_palmas_match_tbl' is always compiled in. Hence of_match_ptr() is
not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Palmas device supports multiple i2c device address and the client
for these addressed are created in the driver as i2c_new_dummy().
The new devices are not getting released in error or removal path and
so it is causing resource leak.
Add the unregister of these newly created dummy devices to avoid resource
leaks.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
If Palams supports the system power controller and pm_power_off
is implemented through the Palmas driver then reset the pm_power_off
in driver remove.
This will avoid the call of Palmas driver after removal of driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| |
|
|
|
| |
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The driver only support the device tree and sub modules are populated
through platform, the registration of sub devices through mfd_add_devices
has been removed.
Hence in remove path of the driver, it is not require to call
mfd_remove_devices.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| |\
| |
| |
| | |
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Hook up "pm_power_off" to palmas power off routine if there is DT
property "ti,system-power-controller" defined, so platform which is
powered by this regulator can be powered off properly.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| |/
|
|
|
|
|
|
|
|
|
| |
Some of Palmas resources like clock, SMPSs, LDOs etc can be controlled
by external pins ENABLE1, ENABLE2 or NSLEEP.
Add support to configure these resources to externally controlled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Patch adds TPS659038 PMIC support in the palmas mfd driver.
The TPS659038 has almost the same registers as of the earlier
supported variants of PALMAS family such as the TWL6035.
The critical differences between TPS659038 and TWL6035 being:
1) TPS659038 has nothing related to battery charging and back up battery stuff.
2) TPS659038 does not have does not have SMPS10(Boost) step up convertor.
3) TPS659038 does not have Battery detection and anything related to battery.
4) SD card detection, Battery presence detection, Vibrator, USB OTG are missing
when compared to TWL6035.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
| |
The SMPS10 regulator is not presesnt in all the variants
of the PALMAS PMIC family. Hence adding a feature to distingush
between them.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
| |
Check if irq value obtained is valid. If it is not valid
then skip the irq request step and go ahead with the probe.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Remove code which is not necessary for a device tree boot.
Boot tested on OMAP5-UEVM board.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Palmas device have three different i2c addresses. The device creates
the two new dummy i2c clients for accessing the register by using
primary client adapter. This new dummy i2c client have their of_node
as NULL.
The dummy i2c client is used for registering interrupt and on this,
it creates irq domain handle. This created irq domain handle has
their of_node as NULL.
Now when any child of this device is registered through the DT as
follows:
palmas: tps65913@58 {
::::::::::::::::::
#interrupt-cells = <2>;
interrupt-controller;
palmas_rtc {
compatible = "ti,palmas-rtc";
interrupt-parent = <&palmas>;
interrupts = <8 0>;
};
::::::::::;;;
};
And child driver (palam-rtc in this case) get their irq number as
irq = platform_get_irq(pdev, 0);
The returned irq number is error in this case. The reason is that
the created irq_domain handle for the palmas interrupt does not have
valid node and so matching of node fails with palmas node.
Hence initialising the newly dummy created client->of_node with the
primary clients of_node so that irq_domain handle have proper of_node
for matching.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
| |
DT node properties should not have "_". Replacing them by "-".
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently driver sets the irq type to IRQF_TRIGGER_LOW which is
causing interrupt registration failure in ARM based SoCs as:
[ 0.208479] genirq: Setting trigger mode 8 for irq 118 failed (gic_set_type+0x0/0xf0)
[ 0.208513] dummy 0-0059: Failed to request IRQ 118: -22
Provide the irq flags through platform data if device is registered
through board file or get the irq type from DT node property in place
of hardcoding the irq flag in driver to support multiple platforms.
Also configure the device to generate the interrupt signal according to
flag type.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Palma RTC is capable of generating alarm interrupt. Pass the alarm interrupt
as IRQ_RESOURCE for palmas-rtc sub device driver so that rtc driver can get
irq as platform_get_irq().
Also pass the irq domain in mfd_add_devices() to properly offset the irqs for
sub devices. This is needed when adding device through DT.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
| |
Add device tree handling to the palmas MFD. This takes the values
that can be set from platform data from the device tree nodes instead.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
| |
Add the platform data and data structures for children that shall be
added by a future set of commits.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Swith the palmas to linear domain in all cases so in future DT and non
DT cases will work the same.
With this patch children no longer need IRQ resources as it's easier
for them to use regmap_get_virq. So we can remove the resources
definitions.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
| |
Improve the error exit path so that we correctly de-allocate resources
that have been allocated upto the point where error occurs.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Using kfree to free data allocated with devm_kzalloc causes double frees.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
x = devm_kzalloc(...)
...
?-kfree(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties. This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern. There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.
Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts. The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
| |
During conversion to regmap_irq this hunk was missing being moved
to MFD driver to put the chip into clear on read mode. Also as slave
is now set use it to determine which slave for the register call.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
| |
Due to a merge error the section of code passing the pdata for the
regulator driver to the mfd_add_devices via the children structure
was missing. This corrects this problem.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
| |
The i2c_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
|
Palmas is a PMIC from Texas Instruments and this is the MFD part of the
driver for this chip. The PMIC has SMPS and LDO regulators, a general
purpose ADC, GPIO, USB OTG mode detection, watchdog and RTC features.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
