summaryrefslogtreecommitdiffstats
path: root/drivers/media/i2c/mt9v032.c
Commit message (Collapse)AuthorAgeFilesLines
* [media] v4l: mt9v032: Add V4L2 controls for AEC and AGCMarkus Pargmann2016-06-281-58/+207
| | | | | | | | | | | | | | | This patch adds V4L2 controls for Auto Exposure Control and Auto Gain Control settings. These settings include low pass filter, update frequency of these settings and the update interval for those units. [Avoid forward declarations] [Fix 80 columns limit violation] [Rename controls to avoid underscores in names] [Fix the AEC maximum shutter width on MT9V032] Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* [media] v4l: mt9v032: Do not unset master_modeMarkus Pargmann2016-06-281-3/+3
| | | | | | | | | | | | | | | | | | | | The power_on function of the driver resets the chip and sets the CHIP_CONTROL register to 0. This switches the operating mode to slave. The s_stream function sets the correct mode. But this caused problems on a board where the camera chip is operated as master. The camera started after a random amount of time streaming an image, I observed between 10 and 300 seconds. The STRFM_OUT and STLN_OUT pins are not connected on this board which may cause some issues in slave mode. I could not find any documentation about this. Keeping the chip in master mode after the reset helped to fix this issue for me. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* [media] v4l: mt9v032: Remove duplicate test for I2C_FUNC_SMBUS_WORD_DATA ↵Axel Lin2016-06-281-7/+0
| | | | | | | | | | | | | | | functionality Since commit b42261078a91 ("regmap: i2c: fallback to SMBus if the adapter does not support standard I2C"), regmap-i2c will check the I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config setting if the adapter does not support standard I2C. So remove the I2C_FUNC_SMBUS_WORD_DATA functionality check in the driver code. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* [media] v4l: mt9v032: Remove unneeded headerLaurent Pinchart2016-06-281-1/+0
| | | | | | | | The of_gpio.h header isn't needed, don't include it. Reported-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* [media] mt9v032: Add reset and standby gpiosMarkus Pargmann2016-01-251-0/+28
| | | | | | | | | | | | | | Add optional reset and standby gpios. The reset gpio is used to reset the chip in power_on(). The standby gpio is not used currently. It is just unset, so the chip is not in standby. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] media framework: rename pads init function to media_entity_pads_init()Mauro Carvalho Chehab2016-01-111-1/+1
| | | | | | | | | | | | | | | | | With the MC next gen rework, what's left for media_entity_init() is to just initialize the PADs. However, certain devices, like a FLASH led/light doesn't have any input or output PAD. So, there's no reason why calling media_entity_init() would be mandatory. Also, despite its name, what this function actually does is to initialize the PADs data. So, rename it to media_entity_pads_init() in order to reflect that. The media entity actual init happens during entity register, at media_device_register_entity(). We should move init of num_links and num_backlinks to it. Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] media: get rid of unused "extra_links" param on media_entity_init()Mauro Carvalho Chehab2016-01-111-1/+1
| | | | | | | | | | | | | | | | | | Currently, media_entity_init() creates an array with the links, allocated at init time. It provides a parameter (extra_links) that would allocate more links than the current needs, but this is not used by any driver. As we want to be able to do dynamic link allocation/removal, we'll need to change the implementation of the links. So, before doing that, let's first remove that extra unused parameter, in order to cleanup the interface first. Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] i2c: constify v4l2_ctrl_ops structuresJulia Lawall2015-11-171-1/+1
| | | | | | | | | | | These v4l2_ctrl_ops structures are never modified, like all the other v4l2_ctrl_ops structures, so declare them as const. Done with the help of Coccinelle. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] include/media: split I2C headers from V4L2 coreMauro Carvalho Chehab2015-11-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, include/media is messy, as it contains both the V4L2 core headers and some driver-specific headers on the same place. That makes harder to identify what core headers should be documented and what headers belong to I2C drivers that are included only by bridge/main drivers that would require the functions provided by them. Let's move those i2c specific files to its own subdirectory. The files to move were produced via the following script: mkdir include/media/i2c (cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done) (cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/*/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done) for i in include/media/*.h; do n=`basename $i`; (for j in $(git grep -l $n); do dirname $j; done)|sort|uniq|grep -ve '^.$' > list; num=$(wc -l list|cut -d' ' -f1); if [ $num == 1 ]; then if [ "`grep i2c list`" != "" ]; then git mv $i include/media/i2c; fi; fi; done And the references corrected via this script: MAIN_DIR="media/" PREV_DIR="media/" DIRS="i2c/" echo "Checking affected files" >&2 for i in $DIRS; do for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do n=`basename $j` git grep -l $n done done|sort|uniq >files && ( echo "Handling files..." >&2; echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\"; ( cd include/$MAIN_DIR; for j in $DIRS; do for i in $(ls $j); do echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\"; done; done; echo "cat > a && mv a \$i; done"; ); echo "Handling documentation..." >&2; echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\"; ( cd include/$MAIN_DIR; for j in $DIRS; do for i in $(ls $j); do echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\"; done; done; echo "cat > a && mv a \$i; done" ); ) >script && . ./script Merged Sakari Ailus patch that moves smiapp.h to include/media/i2c. Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Acked-by: Arnd Bergmann <arnd@arndb.de>
* [media] mt9v032: fix uninitialized variable warningHans Verkuil2015-08-111-1/+1
| | | | | | | | | | | | | drivers/media/i2c/mt9v032.c: In function ‘mt9v032_probe’: CC [M] drivers/media/i2c/s5k4ecgx.o drivers/media/i2c/mt9v032.c:996:20: warning: ‘pdata’ may be used uninitialized in this function [-Wmaybe-uninitialized] if (pdata && pdata->link_freqs) { ^ It can indeed be uninitialized in one corner case. Initialize to NULL. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] v4l: mt9v032: Add OF supportLaurent Pinchart2015-04-021-1/+68
| | | | | | | | | Parse DT properties into a platform data structure when a DT node is available. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] v4l: mt9v032: Consider control initialization errors as fatalLaurent Pinchart2015-04-021-3/+6
| | | | | | | | The device requires control to be properly operated, they're not optional. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] v4l2-subdev: replace v4l2_subdev_fh by v4l2_subdev_pad_configHans Verkuil2015-03-231-18/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a subdevice pad op is called from a bridge driver, then there is no v4l2_subdev_fh struct that can be passed to the subdevice. This made it hard to use such subdevs from a bridge driver. This patch replaces the v4l2_subdev_fh pointer by a v4l2_subdev_pad_config pointer in the pad ops. This allows bridge drivers to use the various try_ pad ops by creating a v4l2_subdev_pad_config struct and passing it along to the pad op. The v4l2_subdev_get_try_* macros had to be changed because of this, so I also took the opportunity to use the full name of the v4l2_subdev_get_try_* functions in the __V4L2_SUBDEV_MK_GET_TRY macro arguments: if you now do 'git grep v4l2_subdev_get_try_format' you will actually find the header where it is defined. One remark regarding the drivers/staging/media/davinci_vpfe patches: the *_init_formats() functions assumed that fh could be NULL. However, that's not true for this driver, it's always set. This is almost certainly a copy and paste from the omap3isp driver. I've updated the code to reflect the fact that fh is never NULL. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] media: drop call to v4l2_device_unregister_subdev()Lad, Prabhakar2015-03-031-1/+0
| | | | | | | | | | These drivers are moved to support asynchronous probing, v4l2_async_unregister_subdev() unregisters the subdev so there isn't a need to explicitly call v4l2_device_unregister_subdev(). Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] v4l2 subdevs: replace get/set_crop by get/set_selectionHans Verkuil2014-12-221-19/+24
| | | | | | | | | | | | | The crop and selection pad ops are duplicates. Replace all uses of get/set_crop by get/set_selection. This will make it possible to drop get/set_crop altogether. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Prabhakar Lad <prabhakar.csengg@gmail.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] i2c: Make use of media_bus_format enumBoris BREZILLON2014-11-141-6/+6
| | | | | | | | | | | | | | | In order to have subsytem agnostic media bus format definitions we've moved media bus definitions to include/uapi/linux/media-bus-format.h and prefixed values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT. Replace all references to the old definitions in i2c drivers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] mt9v032: use regmapPhilipp Zabel2014-07-221-68/+46
| | | | | | | | | | This switches all register accesses to use regmap. It allows to use the regmap cache, tracing, and debug register dump facilities, and removes the need to open code read-modify-writes. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: register v4l2 asynchronous subdevicePhilipp Zabel2014-07-221-1/+11
| | | | | | | | Add support for registering the sensor subdevice using the v4l2-async API. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: add support for mt9v022 and mt9v024Philipp Zabel2014-07-221-8/+32
| | | | | | | | | as are mt9v024 and mt9v034. With minimal changes it is possible to support mt9v02[24] with the same driver. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: do not clear reserved bits in read mode registerPhilipp Zabel2014-07-221-3/+9
| | | | | | | | | The read mode register bits 8 and 9 are set and marked as reserved. Don't clear them. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: fix hblank calculationPhilipp Zabel2014-07-221-2/+2
| | | | | | | | | | | Since (min_row_time - crop->width) can be negative, we have to do a signed comparison here. Otherwise max_t casts the negative value to unsigned int and sets min_hblank to that invalid value. Cc: stable@vger.kernel.org Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] v4l2-ctrls: use ptrs for all but the s32 typeHans Verkuil2014-07-171-1/+1
| | | | | | | | | | | Rather than having two unions for all types just keep 'val' and 'cur.val' and use the p_cur and p_new unions to access all others. The only reason for keeping 'val' and 'cur.val' is that it is used all over, so converting this as well would be a huge job. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] v4l2-ctrls: increase internal min/max/step/def to 64 bitHans Verkuil2014-07-171-1/+1
| | | | | | | | | | | | | | | While VIDIOC_QUERYCTRL is limited to 32 bit min/max/step/def values for controls, the upcoming VIDIOC_QUERY_EXT_CTRL isn't. So increase the internal representation to 64 bits in preparation. Because of these changes the msi3101 driver has been modified slightly to fix a formatting issue (%d becomes %lld), vivi had to be modified as well to cope with the new 64-bit min/max values and the PIXEL_RATE control in a few sensor drivers required proper min/max/def values. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: Check return value of clk_prepare_enable/clk_set_rateLad, Prabhakar2014-02-241-2/+8
| | | | | | | | | clk_set_rate(), clk_prepare_enable() functions can fail, so check the return values to avoid surprises. Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] videodev2: Set vb2_rect's width and height as unsignedRicardo Ribalda2014-01-071-17/+21
| | | | | | | | | | | | | | As discussed on the media summit 2013, there is no reason for the width and height to be signed. Therefore this patch is an attempt to convert those fields from __s32 to __u32. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp) Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: Add support for the MT9V034Laurent Pinchart2013-12-111-8/+46
| | | | | | | | The MT9V034 sensor is very similar to the MT9V032, with a couple of different registers and parameters. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: Add support for model-specific parametersLaurent Pinchart2013-12-111-15/+67
| | | | | | | | To prepare support of the MT9V034, add the necessary infrastructure to support model-specific parameters. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: Add support for monochrome modelsLaurent Pinchart2013-12-111-3/+34
| | | | | | | | Identify the model based on the I2C device name and configure formats accordingly. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: Fix binning configurationLaurent Pinchart2013-12-111-23/+45
| | | | | | | | | The sensor can scale the image down using binning by 1, 2 or 4 in both directions. Update size enumeration and ratio and binning factor computation accordingly. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: Fix pixel array sizeLaurent Pinchart2013-12-111-2/+3
| | | | | | | | The active pixel array size is 753x481 with 4 additional black rows at the top. Fix the driver accordingly. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: Remove unused macroLaurent Pinchart2013-12-111-2/+0
| | | | | | | The EXT_CLK macro is unused, remove it. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] mt9v032: Use the common clock frameworkLaurent Pinchart2013-08-221-6/+11
| | | | | | | | | Configure the device external clock using the common clock framework instead of a board code callback function. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] media: i2c: Convert to devm_kzalloc()Laurent Pinchart2013-05-211-5/+2
| | | | | | | | | | | | Using the managed function the kfree() calls can be removed from the probe error path and the remove handler. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] mt9v032: Free control handler in cleanup pathsLaurent Pinchart2013-05-211-1/+6
| | | | | | | | The control handler must be freed in the probe error path and in the remove handler. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] media: mt9p031/mt9t001/mt9v032: use V4L2_CID_TEST_PATTERN for test ↵Lad, Prabhakar2012-10-051-19/+35
| | | | | | | | | | | | | | pattern control V4L2_CID_TEST_PATTERN is now a standard control. This patch replaces the user defined control for test pattern to make use of standard control V4L2_CID_TEST_PATTERN. Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] mt9v032: Export horizontal and vertical blanking as V4L2 controlsLaurent Pinchart2012-09-131-3/+32
| | | | | Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] mt9v032: Provide link frequency controlLaurent Pinchart2012-09-131-5/+43
| | | | | | Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] mt9v032: Provide pixel rate controlSakari Ailus2012-09-131-2/+25
| | | | | | | | | Provide pixel rate control calculated from external clock and horizontal binning factor. Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] move i2c files into drivers/media/i2cMauro Carvalho Chehab2012-08-151-0/+763
Move ancillary I2C drivers into drivers/media/i2c, in order to better organize them. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OpenPOWER on IntegriCloud