summaryrefslogtreecommitdiffstats
path: root/drivers/input/touchscreen/atmel_mxt_ts.c
Commit message (Collapse)AuthorAgeFilesLines
* Input: atmel_mxt_ts - use mxt_acquire_irq in mxt_soft_resetNick Dyer2016-04-251-14/+14
| | | | | | | | | | | | | | | | If using IRQF_TRIGGER_FALLING, then there is a race here: if the reset completes before we enable the IRQ, then CHG is already low and touch will be broken. This has been seen on Chromebook Pixel 2. A workaround is to reconfig T18 COMMSCONFIG to enable the RETRIGEN bit using mxt-app: mxt-app -W -T18 44 mxt-app --backup Tested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Merge branch 'rotary-encoder' into nextDmitry Torokhov2016-03-041-0/+34
|\ | | | | | | | | | | Bring in updates to roraty encoder driver switching it away from legacy platform data and over to generic device properties and adding support for encoders using more than 2 GPIOs.
| * Input: atmel_mxt_ts - add maxtouch to I2C table for module autoloadJavier Martinez Canillas2015-12-111-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Atmel maxtouch DT binding documents that the compatible string for the device is "atmel,maxtouch" and the I2C core always reports a module alias of the form i2c:alias where alias is the compatible string model: $ grep MODALIAS /sys/devices/platform/12e00000.i2c/i2c-8/8-004b/uevent MODALIAS=i2c:maxtouch But there isn't maxtouch entry in the I2C device ID table so when the i2c:maxtouch MODALIAS uevent is reported, kmod is not able to match the alias with a module to load: $ modinfo atmel_mxt_ts | grep alias alias: of:N*T*Catmel,maxtouch alias: i2c:mXT224 alias: i2c:atmel_mxt_tp alias: i2c:atmel_mxt_ts alias: i2c:qt602240_ts So add the maxtouch entry to the I2C device ID table to allow the module to be autoloaded when the device is registered via OF. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
| * Input: atmel_mxt_ts - add generic platform data for ChromebooksDmitry Torokhov2015-12-021-0/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Apparently people are installing generic Linux distributions not only on Pixels but also on other Chromebooks. Unfortunately on all of them Atmel parts assigned names ATML0000 and ATML0001, and do not carry any other configuration data. So let's create generic instance of platform data that should cover most of them (we assume that they will not be using T100 objects, since with those Google mapped BTN_LEFT onto a different GPIO, so slightly different keymap would be needed, but I think we used parts with T100 on ARM devices where we thankfully have DTS and can describe the devices better). Tested-by: Rich K <rgkirch@gmail.com> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* | Input: atmel_mxt_ts - improve touchscreen size/orientation handlingNick Dyer2016-01-111-42/+26
|/ | | | | | | Both T100 and T9 handle range and orientation in a similar fashion. Reduce duplication between the two implementations. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - remove warning on zero T44 countNick Dyer2015-08-041-9/+8
| | | | Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - initialise input slots with INPUT_MT_DIRECTNick Dyer2015-08-041-0/+2
| | | | | | | | | | | | This indicates the device coordinates should be directly mapped to screen. This is valid since scaling/flipping/rotation should be done by configuring the MXT device. It also flags to Android using INPUT_PROP_DIRECT that the device should be treated as a touch screen by default, and removes the necessity for a default IDC file. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - disable interrupt for 50ms after resetNick Dyer2015-08-041-1/+8
| | | | | | | | The CHG/interrupt line is momentarily set (approximately 100 ms) as an input after power-up or reset for diagnostic purposes. This may cause spurious interrupts, so disable interrupt handler during this period. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - improve device tree parsingNick Dyer2015-08-041-13/+9
| | | | | | Use function rather than loop, define np to reduce wrapping. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - suspend/resume causes panic if input_dev fails to initPan Xinhui2015-08-041-0/+6
| | | | | | | | | input_dev may be NULL if mxt_initialize_input_device fails. But pm ops is still available and suspend/resume assume input_dev is not NULL. To fix this issue, we add a check if (!input_dev). Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com> Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - remove unused definesNick Dyer2015-08-041-65/+1
| | | | | | | | | Many of these values are out of date and they aren't used in the driver - all they do is increase the size of the kernel source. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - use deep sleep mode when stoppedNick Dyer2015-08-041-11/+108
| | | | | | | | | | | | | | | | | | | | | | | | The hardcoded 0x83 CTRL setting overrides other settings in that byte, enabling extra reporting that may not be useful on a particular platform. Implement improved suspend mechanism via deep sleep. By writing zero to both the active and idle cycle times the maXTouch device can be put into a deep sleep mode, using minimal power. It is necessary to issue a calibrate command after the chip has spent any time in deep sleep, however a soft reset is unnecessary. Use the old method on Chromebook Pixel via platform data option. This patch also deals with the situation where the power configuration is zero on probe, which would mean that the device never wakes up to execute commands. After a config download, the T7 power configuration may have changed so it is necessary to re-read it. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: drop owner assignment from i2c_driverKrzysztof Kozlowski2015-07-171-1/+0
| | | | | | | i2c_driver does not need to set an owner because i2c_register_driver() will set it. Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - use BIT() macro when reporting button stateDmitry Torokhov2015-05-201-4/+4
| | | | | | | This makes the intent a tad more clear. Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - add support for Google Pixel 2Dmitry Torokhov2015-04-151-11/+130
| | | | | | | | | | | | | | | | | | This change allows atmel_mxt_ts to bind to ACPI-enumerated devices in Google Pixel 2 (2015). While newer version of ACPI standard allow use of device-tree-like properties in device descriptions, the version of ACPI implemented in Google BIOS does not support them, and we have to resort to DMI data to specify exact characteristics of the devices (touchpad vs. touchscreen, GPIO to button mapping, etc). Pixel 1 continues to use i2c devices and platform data created by chromeos-laptop driver, since ACPI does not enumerate them. Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - split out touchpad initialisation logicSjoerd Simons2015-04-061-22/+30
| | | | | | | | | | | If the "linux,gpio-keymap" DT property is defined, the T19 keys are configured and the device is setup as a touchpad rather than a touchscreen. The logic is part of the input device initialization routine but it can be factored out to its own function to simplify the former. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - implement support for T100 touch objectNick Dyer2015-04-061-27/+318
| | | | | | | | | | | | | | | | | | Add support for the new T100 object which replaces the previous T9 multitouch touchscreen object in recent maXTouch devices. T100 provides improved reporting with selectable auxiliary information, and a type field for hover/stylus/glove reporting. The hovering finger support was based on Chung-Yih's work in the ChromiumOS downstream kernel: https://chromium-review.googlesource.com/#/c/219280/ Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Yufeng Shen <miletus@chromium.org> [javier: Factor out T9 and T100 init functions and rework hover support] Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Revert "Input: atmel_mxt_ts - use deep sleep mode when stopped"Linus Torvalds2014-12-311-73/+26
| | | | | | | | | | | | | | | This reverts commit 9d469d033d135d80742a4e39e6bbb4519dd5eee1. It breaks the Chromebook Pixel touchpad (and touchscreen). Reported-by: Dirk Hohndel <dirk@hohndel.org> Bisected-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nick Dyer <nick.dyer@itdev.co.uk> Cc: Benson Leung <bleung@chromium.org> Cc: Yufeng Shen <miletus@chromium.org> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: stable@vger.kernel.org # v3.16+ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Input: touchscreen - use __maybe_unused instead of ifdef around suspend/resumeJingoo Han2014-11-021-4/+2
| | | | | | | | Use __maybe_unused instead of ifdef guards around suspend/resume functions, in order to increase build coverage and fix build warnings. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - fix double free of input deviceStephen Warren2014-09-101-5/+13
| | | | | | | [Nick Dyer: reworked to move free of input device into separate function and only call in paths that require it.] Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - downgrade warning about empty interruptsNick Dyer2014-09-091-1/+6
| | | | | | | | | In the case where the CHG/interrupt line mode is not configured correctly, this warning is output to dmesg output for each interrupt. Downgrade the message to debug. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - fix a few issues reported by CoverityDmitry Torokhov2014-08-131-6/+11
| | | | | | | | | | | | | | | | | | | This should fix the following issues reported by Coverity: *** CID 1230625: Logically dead code (DEADCODE) /drivers/input/touchscreen/atmel_mxt_ts.c: 1692 in mxt_initialize() *** CID 1230627: Missing break in switch (MISSING_BREAK) /drivers/input/touchscreen/atmel_mxt_ts.c: 1436 in mxt_get_object_table() *** CID 1230629: Out-of-bounds write (OVERRUN) /drivers/input/touchscreen/atmel_mxt_ts.c: 1267 in mxt_update_cfg() *** CID 1230632: Unused pointer value (UNUSED_VALUE) /drivers/input/touchscreen/atmel_mxt_ts.c: 1211 in mxt_update_cfg() Acked-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - split config update a bitDmitry Torokhov2014-08-131-125/+145
| | | | | | | | | Let's split config update code a bit so it is hopefully a bit easier to read. Also, the firmware update callback should be the entity releasing firmware blob, not lower layers. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
* Input: atmel_mxt_ts - simplify mxt_initialize a bitDmitry Torokhov2014-08-131-39/+42
| | | | | | | | I think having control flow with 2 goto/labels/flags is quite hard to read, this version is a bit more readable IMO. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
* Input: atmel_mxt_ts - mXT224 DMA quirk was fixed in firmware v2.0.AANick Dyer2014-08-071-3/+5
| | | | | Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - use deep sleep mode when stoppedNick Dyer2014-07-281-26/+73
| | | | | | | | | | | | | | | | | | | | By writing zero to both the active and idle cycle times the maXTouch device is put into a deep sleep mode when it consumes minimal power. It is unnecessary to change the configuration of any other objects (for example to disable T9 touchscreen). It is counterproductive to reset the chip on resume, it will result in a long delay. However it is necessary to issue a calibrate command after the chip has spent any time in deep sleep. This patch also deals with the situation where the power configuration is zero on probe, which would mean that the device never wakes up to execute commands. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - implement T44 message handlingNick Dyer2014-07-231-32/+159
| | | | | | | | | | | | maXTouch chips allow the reading of multiple messages in a single I2C transaction, which reduces bus overhead and improves performance/latency. The number of messages available to be read is given by the value in the T44 object which is located directly before the T5 object. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - split message handler into separate functionsNick Dyer2014-07-231-59/+64
| | | | | | | | | | | This is in preparation for support of the T44 message count object. Also, cache T5 address to avoid lookup on every interrupt cycle. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - decode T6 status messagesNick Dyer2014-07-231-20/+40
| | | | | | | | | | By storing the previous T6 status byte multiple debug output of the same status can be suppressed (for example CFGERR). Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - add support for dynamic message sizeNick Dyer2014-07-231-52/+68
| | | | | | | | | | | The T5 object may have various sizes depending on the objects used on the particular maXTouch chip and firmware version, therefore it can't be hardcoded in the driver. Allocate a buffer on probe instead. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - recover from bootloader on probeNick Dyer2014-07-231-17/+50
| | | | | | | | | | | | | | | | | | | The MXT device may be in bootloader mode on probe, due to: 1) APP CRC failure, either: a) flash corruption b) bad power or other intermittent problem while checking CRC 2) If the device has been reset 10 or more times without accessing comms 3) Warm probe, device was in bootloader mode already This code attempts to recover from 1(b) and 3. There is an additional complexity: we have to try two possible bootloader addresses because the mapping is not one-to-one and we don't know the exact model yet. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - add bootloader addresses for new chipsNick Dyer2014-07-231-0/+6
| | | | | | | | | | | Later chips (for example mXT1664S) different mappings for bootloader addresses. This means that we must look at the family ID to determine which address to use. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - handle bootloader previously unlockedNick Dyer2014-07-231-9/+18
| | | | | | | | | | On a warm probe, the device might be in a state where an flash operation was not completed. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - handle APP_CRC_FAIL on startupNick Dyer2014-07-231-10/+43
| | | | | | | | | | | If the bootloader on the touchscreen controller fails to initialise the firmware image, it stays in bootloader mode and reports a failure. It is possible to reflash a working firmware image from this state. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - calculate and check CRC in config fileNick Dyer2014-07-231-55/+177
| | | | | | | | | | | By validating the checksum, we can identify if the configuration is corrupt. In addition, this patch writes the configuration in a short series of block writes rather than as many individual values. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - download device config using firmware loaderNick Dyer2014-07-231-74/+204
| | | | | | | | | | | | | | | | | The existing implementation which encodes the configuration as a binary blob in platform data is unsatisfactory since it requires a kernel recompile for the configuration to be changed, and it doesn't deal well with firmware changes that move values around on the chip. Atmel define an ASCII format for the configuration which can be exported from their tools. This patch implements a parser for that format which loads the configuration via the firmware loader and sends it to the MXT chip. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - implement device tree supportStephen Warren2014-07-231-5/+63
| | | | | | Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - set pointer emulation on touchpadsBenson Leung2014-07-231-5/+6
| | | | | | | | | | | Touchpads are pointers, so make sure to pass the correct values to input_mt_report_pointer_emulation(). Without this, tap-to-click doesn't work. Signed-off-by: Benson Leung <bleung@chromium.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - move input device init into separate functionNick Dyer2014-07-231-84/+107
| | | | | | | | | | | | | | | | | It is useful to initialise the input device later: - Screen parameters may not be not known yet, for instance if waiting for firmware loader to return. - Device may be in bootloader mode on probe (but could still be recovered by firmware download). In addition, later devices have a different touchscreen object (T100) which requires handling differently. This also reduces the complexity of the probe function. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - initialise IRQ before probingNick Dyer2014-07-231-39/+62
| | | | | | | | | | | | | | | | | The maXTouch chips use the CHG line to generate status events in bootloader mode, and during configuration download, before there is enough information to configure the input device. Therefore set up the interrupt handler earlier. However, this introduces states where parts of the interrupt processing must not run. Use data->object_table as a way to tell whether the chip information is valid, and data->input_dev as a way to tell whether it is valid to generate input report. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - fix invalid return from mxt_get_bootloader_versionNick Dyer2014-06-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch e57a66aa8534: "Input: atmel_mxt_ts - read and report bootloader version" from May 18, 2014, leads to the following static checker warning: drivers/input/touchscreen/atmel_mxt_ts.c:437 mxt_get_bootloader_version() warn: signedness bug returning '(-5)' drivers/input/touchscreen/atmel_mxt_ts.c 429 static u8 mxt_get_bootloader_version(struct mxt_data *data, u8 val) 430 { 431 struct device *dev = &data->client->dev; 432 u8 buf[3]; 433 434 if (val & MXT_BOOT_EXTENDED_ID) { 435 if (mxt_bootloader_read(data, &buf[0], 3) != 0) { 436 dev_err(dev, "%s: i2c failure\n", __func__); 437 return -EIO; ^^^^ This gets truncated into a number from 0-255 and anyway the caller doesn't check for errors. (reported by Dan Carpenter) Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - handle multiple input reports in one messageNick Dyer2014-05-261-8/+28
| | | | | | | Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - rename touchscreen defines to include T9Nick Dyer2014-05-261-23/+23
| | | | | | | | | This avoids confusion with the newer T100 touchscreen object. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - rename pressure to amplitude to match specNick Dyer2014-05-261-4/+4
| | | | | | | Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - read screen config from chipNick Dyer2014-05-261-71/+65
| | | | | | | | | | | | | | By reading the touchscreen configuration from the settings that the maXTouch chip is actually using, we can remove some platform data. The matrix size is not used for anything, and results in some rather confusing code to re-read it because it may change when configuration is downloaded, so don't print it out. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - add check for incorrect firmware file formatNick Dyer2014-05-181-0/+29
| | | | | | | | | | | | Atmel supplies firmware files in ASCII HEX format (.enc) which must be converted before they can be loaded by kernel driver. Try to detect the error and print a friendly error message rather than feeding junk to the bootloader. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - improve bootloader progress outputNick Dyer2014-05-181-1/+7
| | | | | | | | | | By implementing a frame counter, print out fewer debug messages (the firmware may contain hundreds of frames). Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - implement bootloader frame retriesNick Dyer2014-05-181-7/+20
| | | | | | | Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - read and report bootloader versionNick Dyer2014-05-181-0/+26
| | | | | | | Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* Input: atmel_mxt_ts - add additional bootloader addressesNick Dyer2014-05-181-45/+93
| | | | | | | | | | | Move bootloaders reads/writes into separate functions. Instead of switching client->addr, define new field bootloader_addr in mxt_data. Implement lookup calculation for bootloader addresses. Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Acked-by: Benson Leung <bleung@chromium.org> Acked-by: Yufeng Shen <miletus@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
OpenPOWER on IntegriCloud