| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
commit 98ad8b41f58dff6b30713d7f09ae3834b8df7ded
("iio: st_sensors: verify interrupt event to status") caused
a regression when reading ST sensors from a HRTimer trigger
rather than the intrinsic interrupts: the HRTimer may
trigger faster than the sensor provides new values, and
as the check against new values available as a cause of
the interrupt trigger was done in the poll function,
this would bail out of the HRTimer interrupt with
IRQ_NONE.
So clearly we need to only check the new values available
from the proper interrupt handler and not from the poll
function, which should rather just read the raw values
from the registers, put them into the buffer and be happy.
To achieve this: switch the ST Sensors over to using a true
threaded interrupt handler.
In the interrupt thread, check if new values are available,
else yield to the (potential) next device on the same
interrupt line to check the registers. If the interrupt
was ours, proceed to poll the values.
Instead of relying on iio_trigger_generic_data_rdy_poll() as
a top half to wake up the thread that polls the sensor for
new data, have the thread call iio_trigger_poll_chained()
after determining that is is the proper source of the
interrupt. This is modelled on drivers/iio/accel/mma8452.c
which is already using a properly threaded interrupt handler.
In order to get the same precision in timestamps as
previously, where samples would be timestamped in the
poll function pf->timestamp when calling
iio_trigger_generic_data_rdy_poll() we introduce a
local timestamp in the sensor data, set it in the top half
(fastpath) of the interrupt handler and provide that to the
core when calling iio_push_to_buffers_with_timestamp().
Additionally: if the active scanmask is not set for the
sensor no IRQs should be enabled and we need to bail out
with IRQ_NONE. This can happen if spurious IRQs fire when
installing the threaded interrupt handler.
Tested with hard interrupt triggers on LIS331DL, then also
tested with hrtimers on the same sensor by creating a 75Hz
HRTimer and using it to poll the sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Fixes: 97865fe41322 ("iio: st_sensors: verify interrupt event to status")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
2nd set of new device support, features and cleanup for IIO in the 4.7 cycle.
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
|
| |
| |
| |
| |
| |
| |
| |
| | |
This device has an identical interface to other supported sensors and the patch
only adds IDs.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Driver includes struct regmap and struct device in its global data.
Remove the struct device and use regmap API to retrieve device info.
Patch created using Coccinelle plus manual edits.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This makes all ST sensor drivers check that they actually have
new data available for the requested channel(s) before claiming
an IRQ, by reading the status register (which is conveniently
the same for all ST sensors) and check that the channel has new
data before proceeding to read it and fill the buffer.
This way sensors can share an interrupt line: it can be flaged
as shared and then the sensor that did not fire will return
NO_IRQ, and the sensor that fired will handle the IRQ and
return IRQ_HANDLED.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|\ \
| |/
|/|
| |
| |
| |
| | |
This resolves a lot of merge issues with PAGE_CACHE_* changes, and an
iio driver merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When reading gyroscope axes using iio buffers, the values
returned are always 0. In the interrupt handler, the return
value of the read operation is returned to the user instead
of the value read. Return the value read to the user.
This is also fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
For big endian platforms, reading the axes will return
invalid values.
The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.
Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.
This is also partially fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit 845c877009cf014b ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") automatically assigns the first ACPI GPIO
interrupt in client->irq, so we can remove the probing code from
drivers that use only one interrupt.
Commit 0f0796509c07c1c7 ("iio: remove gpio interrupt probing from drivers
that use a single interrupt") removes gpio interrupt probing from most
drivers. This patch cleans the remaining ones.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to
enable/disable the bus at each i2c transfer and must wait for
the enable/disable to happen before sending the data.
When reading data in the trigger handler, the bmg160 gyro driver does
one bus transfer for each axis. This has an impact on the frequency
of the accelerometer at high sample rates due to additional delays
introduced by the bus at each transfer.
Reading all axis values in one bus transfer reduces the delays
introduced by the bus.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|/
|
|
|
|
|
|
|
|
| |
Use available_scan_masks to allow the iio core to select
the data to send to userspace depending on which axes are
enabled, instead of doing this in the driver's interrupt
handler.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Most ST MEMS Sensors that support interrupts can also handle sending
an active low interrupt, i.e. going from high to low on data ready
(or other interrupt) and thus triggering on a falling edge to the
interrupt controller.
Set up logic to inspect the interrupt line we get for a sensor: if
it is triggering on rising edge, leave everything alone, but if it
triggers on falling edges, set up active low, and if unsupported
configurations appear: warn with errors and reconfigure the interrupt
to a rising edge, which all interrupt generating sensors support.
Create a local header for st_sensors_core.h to share functions
between the sensor core and the trigger setup code.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.5 cycle
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch fixes the checkpatch warnings:
WARNING: unchecked sscanf return value
Signed-off-by: Ioana Ciornei <ciorneiioana@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
At probe, runtime pm should be setup before registering the sysfs interface so
that all the power attributes are accurate and functional when registering.
Also, when removing the device we should unregister first to make sure
that the interfaces that may result in wakeups are no longer available.
Fix this behaviour for the following drivers: bmc150, bmg160, kmx61,
kxcj-1013, mma9551, mma9553, rpr0521.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|\ \
| |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
| |
| |
| |
| | |
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch separates the core driver using regmap and the i2c driver
which creates the i2c regmap. Also in the Kconfig file BMG160 and
BMG160_I2C are separate now.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This adds a debugfs hook to read/write registers in the ST
sensors using debugfs. Proved to be awesome help when trying
to debug why IRQs do not arrive.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| | |
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
i2c_get_clientdata() is specifically for i2c. Replace it with the
generic dev_get/set_drvdata() to support different protocols.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
i2c_client variable is not really used anymore in the core driver. It is
only used to get the device to make proper outputs.
This patch replaces all i2c_client usage through direct usage of the
device pointer.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|/
|
|
|
|
|
|
|
| |
This patch introduces regmap usage into the driver. This is done to
later easily support the SPI interface of this chip.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
|
|
|
|
|
|
|
|
| |
This patch adds selects for IIO_BUFFER and IIO_TRIGGERED_BUFFER. Without
IIO_BUFFER, the driver does not compile.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
|
|
|
|
|
|
| |
The ADIS16137 is register map compatible to the ADIS16136, but has a
different scale factor for the gyroscope output.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
|
|
|
|
|
|
|
| |
The ADIS16266 is mostly register compatible to the ADIS16260. The
difference is a different gyroscope scale factor as well not having the
relative angular displacement channel.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
| |
This patch permits to configure the WhoAmI register address
because some device could have not a standard address for
this register.
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
Reviewed-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
|
|
|
|
|
|
| |
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new driver, functionality and cleanups for IIO in the 4.2 cycle.
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
|
| |
| |
| |
| |
| |
| |
| |
| | |
Make it possible to use buffering with an external trigger, such as one
based on sysfs or hrtimer.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Replace the 'timestamp' field in struct bmg160_data with the identically
named field in iio_poll_func and with calls to iio_get_time_ns().
The reported timestamps may be slightly different, but the advantage is
that we no longer assume that the buffer of bmg160 is triggered by its
own trigger.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
'channels' is allocated via kmemdup and it is never freed in the
subsequent error paths.
Use 'indio_dev->channels' directly instead, so that we avoid such
memory leak problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| | |
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|\ \
| |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
The usual mixed bag of fixes for IIO in the 4.1 cycle.
Second version of this pull request as a small fix to a fix turned
up before Greg pulled it for a cc10001 patch near the top of the tree.
One core fix
* Set updated for a iio kfifo was incorrectly set to false during a failed
update, resulting in atttempts to repeat the failed operation appearing
to succeed.
This time I've decided to list the driver fixes in alphabetical order rather
than 'randomly'.
* axp288_adc - a recent change added a check for valid info masks when
reading channels from consumer drivers.
* bmp280 - temperature compensation was failing to read the tfine value, hence
causing a temperature of 0 to always be returned and incorrect presure
measurements.
* cc10001 - Fix channel number mapping when some channels are reserved for
remote CPUs. Fix an issue with the use of the power-up/power-down register
(basically wrong polarity). Fix an issue due to the missinterpretting the
return value from regulator_get_voltage. Add a delay before the start bit
as recommended for the hardware to avoid data corruption.
* hid pressure - fix channel spec of modfiied, but no modifier (which makes no
sense!)
* hid proximity - fix channel spec of modified, but no modifier (which makes
no sense!). Fix a memory leak in the probe function.
* mcp320x - occasional incorrect readings on dma using spi busses due to
cacheline corruption. Fixed by forcing ___cacheline_aligned for the buffers.
* mma9551 - buffer overrun fix (miss specified maximum length of buffers)
* mma9553 - endian fix on status message. Add an enable element for activity
channel. Input checking for activity period to avoid rather unpredictable
results.
* spmi-vadc - fix an overflow in the output value normalization seen on some
boards.
* st-snesors - oops due to use of a mutex that is not yet initialized during
probe.
* xilinx adc - Some wrong register addresses, a wrong address for vccaux
channel, incorrect scale on VREFP and incorrect sign on VREFN.
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In SPI mode the transfer buffer is locked with a mutex. However this
mutex is only initilized after the probe, but some transfer needs to
be done in the probe.
To fix this bug we move the mutex initialization at the beginning of
the device probe.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|\ \
| |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
|
| |\
| | |
| | |
| | |
| | |
| | | |
Conflicts:
drivers/iio/common/hid-sensors/hid-sensor-trigger.c
include/linux/hid-sensor-hub.h
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add additional flag to read in async mode. In this mode the caller will get
reply via registered callback for capture_sample. Callbacks can be registered
using sensor_hub_register_callback function. The usage id parameter of the
capture_sample can be matched with the usage id of the requested attribute.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We want those fixes (iio primarily) into the -next branch to help with
merge and testing issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
If the in-kernel push interface is used we may have a different masks
on the device buffer and the kernel buffer and in this case the device
should generate data for the reunion of the buffers, which is
available at indio_dev->active_scan_mask.
Compiled tested only except for bmc150-accel which was tested at
runtime with the hardware.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
It can be used exactly like L3GD20 but it has a different WhoAmI
register value.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Unless we put the device to sleep when not it use, it wastes
6mA.
If the device is asleep on probe, the 'id' register
sometimes mis-reads - so reset first. If the device responds
at all a command sent to the address, it is almost certainly
the correct device already.
Acked-by: Manuel Stahl <manuel.stahl@iis.fraunhofer.de>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|/ /
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Since 39b2bbe3d715 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
outputs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch adds gyroscope iio driver which uses sensorhub as data
provider.
Signed-off-by: Karol Wrona <k.wrona@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|/
|
|
|
|
|
|
|
| |
Use common hid sensor iio pm functions. Also the poll time read and
wait is part of power up function of hid sensor iio pm function, so
remove from the client drivers.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big staging tree pull request for 3.19-rc1.
We continued to delete more lines than were added, always a good
thing, but not at a huge rate this release, only about 70k lines
removed overall mostly from removing the horrid bcm driver.
Lots of normal staging driver cleanups and fixes all over the place,
well over a thousand of them, the shortlog shows all the horrid
details.
The "contentious" thing here is the movement of the Android binder
code out of staging into the "real" part of the kernel. This is code
that has been stable for a few years now and is working as-is in the
tens of millions of devices with no issues. Yes, the code is horrid,
and the userspace api leaves a lot to be desired, but it's not going
to change due to legacy issues that we have no control over. Because
so many devices and companies rely on this, and the code is stable,
might as well promote it out of staging.
This was all discussed at the Linux Plumbers conference, and everyone
participating agreed that this was the best way forward.
There is work happening to replace the binder code with something new
that is happening right now, but I don't expect to see the results of
that work for another year at the earliest. If that ever happens, and
Android switches over to it, I'll gladly remove this version.
As for maintainers, I'll be glad to maintain this code, I've been
doing it for the past few years with no problems. I'll send a
MAINTAINERS entry for it before 3.19-final is out, still need to talk
to the Google developers about if they are willing to help with it or
not, last I checked they were, which was good.
All of these patches have been in linux-next for a while with no
reported issues"
* tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1382 commits)
Staging: slicoss: Fix long line issues in slicoss.c
staging: rtl8712: remove unnecessary else after return
staging: comedi: change some printk calls to pr_err
staging: rtl8723au: hal: Removed the extra semicolon
lustre: Deletion of unnecessary checks before three function calls
staging: lustre: fix sparse warnings: static function declaration
staging: lustre: fixed sparse warnings related to static declarations
staging: unisys: remove duplicate header
staging: unisys: remove unneeded structure
staging: ft1000 : replace __attribute ((__packed__) with __packed
drivers: staging: rtl8192e: Include "asm/unaligned.h" instead of "access_ok.h" in "rtl819x_BAProc.c"
Drivers:staging:rtl8192e: Fixed checkpatch warning
Drivers:staging:clocking-wizard: Added a newline
staging: clocking-wizard: check for a valid clk_name pointer
staging: rtl8723au: Hal_InitPGData() avoid unnecessary typecasts
staging: rtl8723au: _DisableAnalog(): Avoid zero-init variables unnecessarily
staging: rtl8723au: Remove unnecessary wrapper _ResetDigitalProcedure1()
staging: rtl8723au: _ResetDigitalProcedure1_92C() reduce code obfuscation
staging: rtl8723au: Remove unnecessary wrapper _DisableRFAFEAndResetBB()
staging: rtl8723au: _DisableRFAFEAndResetBB8192C(): Reduce code obfuscation
...
|
| |\
| | |
| | |
| | |
| | |
| | | |
We want those staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, features and cleanups for IIO in the 3.19 cycle.
New drivers / supported parts
* rockchip - rk3066-tsadc variant
* si7020 humidity and temperature sensor
* mcp320x - add mcp3001, mcp3002, mcp3004, mcp3008, mcp3201, mcp3202
* bmp280 pressure and temperature sensor
* Qualcomm SPMI PMIC current ADC driver
* Exynos_adc - support exynos7
New features
* vf610-adc - add temperature sensor support
* Documentation of current attributes, scaled pressure, offset and
scaled humidity, RGBC intensity gain factor and scale applied to
differential voltage channels.
* Bring iio_event_monitor up to date with newer modifiers.
* Add of_xlate function to allow for complex channel mappings from the
device tree.
* Add -g parameter to generic_buffer example to allow for devices with
directly fed (no trigger) buffers.
* Move exynos driver over to syscon for PMU register access.
Cleanups, fixes for new drivers
* lis3l02dq drop an unneeded else.
* st sensors - renam st_sensors to st_sensor_settings (for clarity)
* st sensors - drop an unused parameter from all the probe utility
functions.
* vf610 better error handling and tidy up.
* si7020 - cleanups following merge
* as3935 - drop some unnecessary semicolons.
* bmp280 - fix the pressure calculation.
|
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|