| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The audio chicken bit (register offset 0x62f38) seems required to make
DP audio working on some machines. At least, on Dell Wyse 3040, I
failed to get the audio unless this bit is set once.
Strangely, the bit seems necessary only once, and it persists after
that, even some power-off cycles. The register is supposedly
write-only, so it's no evidence whether the bit keeps effect
persistently. But, judging from the experiment, it looks enough to
set it up once at the device initialization.
The patch is basically a cut from the original patch by Pierre-Louis
Bossart.
v1->v2: drop read since it's a write-only reg.
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
| |
This allows the LPE HDMI driver to clean up its global variable
reference.
Also drop to pass the eld pointer because the connection status and
the ELD bytes can be retrieved from the attached pdata.
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
| |
The LPE audio configuration depends on the pipe, thus we need to pass
the currently used pipe. It's now embedded in struct
intel_hdmi_lpe_audio_eld as well as port id.
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Enable unmute/mute amp notification. This doesn't seem to affect
HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address 0x62F38
prior to the mute/unmute but this register doesn't seem to do anything
so this phase was removed.
v1->v2: Drop needless pipe A check, avoid temporary reg offset variable.
v2->v3: Add "_" prefix to VLV_AUD_PORT_EN_X_DBG as they are internal.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
| |
If DisplayPort is detected, pass flag and link rate to audio driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Notifiations like mode change, hot plug and edid to
the audio driver are added. This is inturn used by the
audio driver for its functionality.
A new interface file capturing the notifications needed by the
audio driver is added
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jerome Anand <jerome.anand@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
Enable support for HDMI LPE audio mode on Baytrail and
Cherrytrail when HDaudio controller is not detected
Setup minimum required resources during i915_driver_load:
1. Create a platform device to share MMIO/IRQ resources
2. Make the platform device child of i915 device for runtime PM.
3. Create IRQ chip to forward HDMI LPE audio irqs.
HDMI LPE audio driver (a standalone sound driver) probes the
LPE audio device and creates a new sound card.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jerome Anand <jerome.anand@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
