summaryrefslogtreecommitdiffstats
path: root/drivers/ata/libata-eh.c
Commit message (Collapse)AuthorAgeFilesLines
* libata: improve EH retry delay handlingTejun Heo2008-07-141-18/+20
| | | | | | | | | | | | | | | | | | | | | | | EH retries were delayed by 5 seconds to ensure that resets don't occur back-to-back. However, this 5 second delay is superflous or excessive in many cases. For example, after IDENTIFY times out, there's no reason to wait five more seconds before retrying. This patch adds ehc->last_reset timestamp and record the timestamp for the last reset trial or success and uses it to space resets by ATA_EH_RESET_COOL_DOWN which is 5 secs and removes unconditional 5 sec sleeps. As this change makes inter-try waits often shorter and they're redundant in nature, this patch also removes the "retrying..." messages. While at it, convert explicit rounding up division to DIV_ROUND_UP(). This change speeds up EH in many cases w/o sacrificing robustness. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: consistently use msecs for time durationsTejun Heo2008-07-141-16/+17
| | | | | | | | | | | | | | | | libata has been using mix of jiffies and msecs for time druations. This is getting confusing. As writing sub HZ values in jiffies is PITA and msecs_to_jiffies() can't be used as initializer, unify unit for all time durations to msecs. So, durations are in msecs and deadlines are in jiffies. ata_deadline() is added to compute deadline from a start time and duration in msecs. While at it, drop now superflous _msec suffix from arguments and rename @timeout to @deadline if it represents a fixed point in time rather than duration. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: ignore recovered PHY errorsTejun Heo2008-05-191-6/+1
| | | | | | | | | | | | | | | No reason to get overzealous about recovered comm and data errors. Some PHYs habitually sets them w/o no good reason and being draconian about these soft error conditions doesn't seem to help anybody. If need ever rises, we might need to add soft PHY error condition, say AC_ERR_MAYBE_ATA_BUS and use it only to determine whether speed down is necessary but I don't think that's very likely to happen. It's far more likely we'll get timeouts or fatal transmission errors if recovered errors are so prominent that they hamper operation. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: kill hotplug related race conditionTejun Heo2008-05-191-10/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Originally, whole reset processing was done while the port is frozen and SError was cleared during @postreset(). This had two race conditions. 1: hotplug could occur after reset but before SError is cleared and libata won't know about it. 2: hotplug could occur after all the reset is complete but before the port is thawed. As all events are cleared on thaw, the hotplug event would be lost. Commit ac371987a81c61c2efbd6931245cdcaf43baad89 kills the first race by clearing SError during link resume but before link onlineness test. However, this doesn't fix race #2 and in some cases clearing SError after SRST is a good idea. This patch solves this problem by cross checking link onlineness with classification result after SError is cleared and port is thawed. Reset is retried if link is online but all devices attached to the link are unknown. As all devices will be revalidated, this one-way check is enough to ensure that all devices are detected and revalidated reliably. This, luckily, also fixes the cases where host controller returns bogus status while harddrive is spinning up after hotplug making classification run before the device sends the first FIS and thus causes misdetection. Low level drivers can bypass the logic by setting class explicitly to ATA_DEV_NONE if ever necessary (currently none requires this). Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: move reset freeze/thaw handling into ata_eh_reset()Tejun Heo2008-05-191-28/+18
| | | | | | | | | | | | | | | | | Previously reset freeze/thaw handling lived outside of ata_eh_reset() mainly because the original PMP reset code needed the port frozen while resetting all the fan-out ports, which is no longer the case. This patch moves freeze/thaw handling into ata_eh_reset(). @prereset() and @postreset() are now called w/o freezing the port although @prereset() an be called frozen if the port is frozen prior to entering ata_eh_reset(). This makes code simpler and will help removing hotplug event related races. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: reorganize ata_eh_reset() no reset method pathTejun Heo2008-05-191-50/+52
| | | | | | | | | | Reorganize ata_eh_reset() such that @prereset() is called even when no reset method is available and if block is used instead of goto to skip actual reset. This makes no reset case behave better (readiness wait) and future changes easier. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: export ata_eh_analyze_ncq_errorMark Lord2008-05-061-1/+1
| | | | | | | | Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv, as suggested by Tejun. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata-eh set tf flags in NCQ EH result_tfMark Lord2008-04-251-0/+1
| | | | | | | | | | | | | | | Fix mis-reporting of NCQ errors by ensuring that result_tf->flags is properly initialized in libata-eh. This allows ata_gen_ata_sense() to report the failed block number correctly to SCSI after a media error during NCQ. This patch may also be a candidate for backporting to earlier kernels. Without this fix, SCSI will fail I/O on the entire request rather than just the bad sector. That can be bad for a request that was merged from many independent read reads from different tasks. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: make EH fail gracefully if no reset method is availableTejun Heo2008-04-171-1/+6
| | | | | | | | | | When no reset method is available, libata currently oopses. Although the condition can't happen unless there's a bug in a low level driver, oopsing isn't the best way to report the error condition. Complain, dump stack and fail reset instead. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: move link onlineness check out of softreset methodsTejun Heo2008-04-171-1/+1
| | | | | | | | | | | | | | | | | | | Currently, SATA softresets should do link onlineness check before actually performing SRST protocol but it doesn't really belong to softreset. This patch moves onlineness check in softreset to ata_eh_reset() and ata_eh_followup_srst_needed() to clean up code and help future sata_mv changes which need clear separation between SCR and TF accesses. sata_fsl is peculiar in that its softreset really isn't softreset but combination of hardreset and softreset. This patch adds dummy private ->prereset to keep the current behavior but the driver really should implement separate hard and soft resets and return -EAGAIN from hardreset if it should be follwed by softreset. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: kill dead code paths in reset pathTejun Heo2008-04-171-18/+1
| | | | | | | | | | | | | | | | Some code paths which had been made obsolete by recent reset simplification were still around. Kill them. * ata_eh_reset() checked for ATA_DEV_UNKNOWN to determine classification failure. This is no longer applicable. * ata_do_reset() should convert ATA_DEV_UNKNOWN to ATA_DEV_NONE regardless of reset result (e.g. -EAGAIN). * LLDs don't need to convert ATA_DEV_UNKNOWN to ATA_DEV_NONE. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: implement PMP helpersTejun Heo2008-04-171-7/+7
| | | | | | | | | | | Implement helpers to test whether PMP is supported, attached and determine pmp number to use when issuing SRST to a link. While at it, move ata_is_host_link() so that it's together with the two new PMP helpers. This change simplifies LLDs and helps making PMP support optional. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: unify mechanism to request follow-up SRSTTejun Heo2008-04-171-18/+8
| | | | | | | | | | | | | Previously, there were two ways to trigger follow-up SRST from hardreset method - returning -EAGAIN and leaving all device classes unmodified. Drivers never used the latter mechanism and the only use case for the former was when hardreset couldn't classify. Drop the latter mechanism and let -EAGAIN mean "perform follow-up SRST if classification is required". This change removes unnecessary follow-up SRSTs and simplifies reset implementations. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: move PMP SCR access failure during reset to ata_eh_reset()Tejun Heo2008-04-171-0/+5
| | | | | | | | | | | | | | If PMP fan-out reset fails and SCR isn't accessible, PMP should be reset. This used to be tested by sata_pmp_std_hardreset() and communicated to EH by -ERESTART. However, this logic is generic and doesn't really have much to do with specific hardreset implementation. This patch moves SCR access failure detection logic to ata_eh_reset() where it belongs. As this makes sata_pmp_std_hardreset() identical to sata_std_hardreset(), the function is killed and replaced with the standard method. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: implement and use sata_std_hardreset()Tejun Heo2008-04-171-5/+2
| | | | | | | | | | | | | | | | | | Implement sata_std_hardreset(), which simply wraps around sata_link_hardreset(). sata_std_hardreset() becomes new standard hardreset method for sata_port_ops and sata_sff_hardreset() moves from ata_base_port_ops to ata_sff_port_ops, which is where it really belongs. ata_is_builtin_hardreset() is added so that both ata_std_error_handler() and ata_sff_error_handler() skip both builtin hardresets if SCR isn't accessible. piix_sidpr_hardreset() in ata_piix.c is identical to sata_std_hardreset() in functionality and got replaced with the standard function. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: rename SFF functionsTejun Heo2008-04-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SFF functions have confusing names. Some have sff prefix, some have bmdma, some std, some pci and some none. Unify the naming by... * SFF functions which are common to both BMDMA and non-BMDMA are prefixed with ata_sff_. * SFF functions which are specific to BMDMA are prefixed with ata_bmdma_. * SFF functions which are specific to PCI but apply to both BMDMA and non-BMDMA are prefixed with ata_pci_sff_. * SFF functions which are specific to PCI and BMDMA are prefixed with ata_pci_bmdma_. * Drop generic prefixes from LLD specific routines. For example, bfin_std_dev_select -> bfin_dev_select. The following renames are noteworthy. ata_qc_issue_prot() -> ata_sff_qc_issue() ata_pci_default_filter() -> ata_bmdma_mode_filter() ata_dev_try_classify() -> ata_sff_dev_classify() This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames functions and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: implement ATA_QCFLAG_RETRYTejun Heo2008-04-171-10/+8
| | | | | | | | | | Currently whether a command should be retried after failure is determined inside ata_eh_finish(). Add ATA_QCFLAG_RETRY and move the logic into ata_eh_autopsy(). This makes things clearer and helps extending retry determination logic. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: make reset related methods proper port operationsTejun Heo2008-04-171-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently reset methods are not specified directly in the ata_port_operations table. If a LLD wants to use custom reset methods, it should construct and use a error_handler which uses those reset methods. It's done this way for two reasons. First, the ops table already contained too many methods and adding four more of them would noticeably increase the amount of necessary boilerplate code all over low level drivers. Second, as ->error_handler uses those reset methods, it can get confusing. ie. By overriding ->error_handler, those reset ops can be made useless making layering a bit hazy. Now that ops table uses inheritance, the first problem doesn't exist anymore. The second isn't completely solved but is relieved by providing default values - most drivers can just override what it has implemented and don't have to concern itself about higher level callbacks. In fact, there currently is no driver which actually modifies error handling behavior. Drivers which override ->error_handler just wraps the standard error handler only to prepare the controller for EH. I don't think making ops layering strict has any noticeable benefit. This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and their PMP counterparts propoer ops. Default ops are provided in the base ops tables and drivers are converted to override individual reset methods instead of creating custom error_handler. * ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs aren't accessible. sata_promise doesn't need to use separate error_handlers for PATA and SATA anymore. * softreset is broken for sata_inic162x and sata_sx4. As libata now always prefers hardreset, this doesn't really matter but the ops are forced to NULL using ATA_OP_NULL for documentation purpose. * pata_hpt374 needs to use different prereset for the first and second PCI functions. This used to be done by branching from hpt374_error_handler(). The proper way to do this is to use separate ops and port_info tables for each function. Converted. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: kill ata_ehi_schedule_probe()Tejun Heo2008-04-171-1/+1
| | | | | | | | | | | | | | | | ata_ehi_schedule_probe() was created to hide details of link-resuming reset magic. Now that all the softreset workarounds are gone, scheduling probe is very simple - set probe_mask and request RESET. Kill ata_ehi_schedule_probe() and open code it. This also increases consistency as ata_ehi_schedule_probe() couldn't cover individual device probings so they were open-coded even when the helper existed. While at it, define ATA_ALL_DEVICES as mask of all possible devices on a link and always use it when requesting probe on link level for simplicity and consistency. Setting extra bits in the probe_mask doesn't hurt anybody. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: kill ATA_EHI_RESUME_LINKTejun Heo2008-04-171-13/+8
| | | | | | | | | | | | | | ATA_EHI_RESUME_LINK has two functions - promote reset to hardreset if ATA_LFLAG_HRST_TO_RESUME is set and preventing EH from shortcutting reset action when probing is requested. The former is gone now and the latter can easily be achieved by making EH to perform at least one reset if reset is requested, which also makes more sense than depending on RESUME_LINK flag. As ATA_EHI_RESUME_LINK was the only EHI reset modifier, this also kills reset modifier handling. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: prefer hardresetTejun Heo2008-04-171-64/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When both soft and hard resets are available, libata preferred softreset till now. The logic behind it was to be softer to devices; however, this doesn't really help much. Rationales for the change: * BIOS may freeze lock certain things during boot and softreset can't unlock those. This by itself is okay but during operation PHY event or other error conditions can trigger hardreset and the device may end up with different configuration. For example, after a hardreset, previously unlockable HPA can be unlocked resulting in different device size and thus revalidation failure. Similar condition can occur during or after resume. * Certain ATAPI devices require hardreset to recover after certain error conditions. On PATA, this is done by issuing the DEVICE RESET command. On SATA, COMRESET has equivalent effect. The problem is that DEVICE RESET needs its own execution protocol. For SFF controllers with bare TF access, it can be easily implemented but more advanced controllers (e.g. ahci and sata_sil24) require specialized implementations. Simply using hardreset solves the problem nicely. * COMRESET initialization sequence is the norm in SATA land and many SATA devices don't work properly if only SRST is used. For example, some PMPs behave this way and libata works around by always issuing hardreset if the host supports PMP. Like the above example, libata has developed a number of mechanisms aiming to promote softreset to hardreset if softreset is not going to work. This approach is time consuming and error prone. Also, note that, dependingon how you read the specs, it could be argued that PMP fan-out ports require COMRESET to start operation. In fact, all the PMPs on the market except one don't work properly if COMRESET is not issued to fan-out ports after PMP reset. * COMRESET is an integral part of SATA connection and any working device should be able to handle COMRESET properly. After all, it's the way to signal hardreset during reboot. This is the most used and recommended (at least by the ahci spec) method of resetting devices. So, this patch makes libata prefer hardreset over softreset by making the following changes. * Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever ATA_EH_{SOFT|HARD}RESET used to be used. ATA_EH_{SOFT|HARD}RESET is now only used to tell prereset whether soft or hard reset will be issued. * Strip out now unneeded promote-to-hardreset logics from ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and other places. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: ATA_EHI_LPM should be ATA_EH_LPMTejun Heo2008-03-291-1/+1
| | | | | | | | | EH actions are ATA_EH_* not ATA_EHI_*. Rename ATA_EHI_LPM to ATA_EH_LPM. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: allow LLDs w/o any reset methodTejun Heo2008-03-101-0/+10
| | | | | | | | | | Some old SFF controllers don't have any way to reset the channel. Currently, this isn't supported and libata EH causes an oops. Allow LLDs w/o any reset method and just assume ATA class in such cases. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: implement libata.force module parameterTejun Heo2008-02-201-3/+5
| | | | | | | | | | | | | | | | This patch implements libata.force module parameter which can selectively override ATA port, link and device configurations including cable type, SATA PHY SPD limit, transfer mode and NCQ. For example, you can say "use 1.5Gbps for all fan-out ports attached to the second port but allow 3.0Gbps for the PMP device itself, oh, the device attached to the third fan-out port chokes on NCQ and shouldn't go over UDMA4" by the following. libata.force=2:1.5g,2.15:3.0g,2.03:noncq,udma4 Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: fix off-by-one in error categorizationTejun Heo2008-01-231-7/+6
| | | | | | | | | | | | | ATA_ECAT_DUBIOUS_BASE was too high by one and thus all DUBIOUS error categorizations were wrong. This passed test because only ATA_BUS and UNK_DEV were used during testing and the ones after them - ATA_BUS and an overflowed entry - behaved similarly. This patch fixes the problem by adding DUBIOUS_NONE category and use it as base. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: rename ATA_PROT_ATAPI_* to ATAPI_PROT_*Tejun Heo2008-01-231-4/+4
| | | | | | | | | ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and ATA_PROT_ATAPI_* are inconsistent causing confusion. Rename them to ATAPI_PROT_* and make them consistent with ATA counterpart. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* drivers/ata/libata-eh.c: fix printk warningAndrew Morton2008-01-231-1/+2
| | | | | | | | | drivers/ata/libata-eh.c: In function `ata_port_pbar_desc': drivers/ata/libata-eh.c:215: warning: long long unsigned int format, long unsigned int arg (arg 4) Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] Build fix WRT ata_is_xxx() new API introductionJeff Garzik2008-01-231-1/+1
| | | | Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: implement fast speed down for unverified data transfer modeTejun Heo2008-01-231-14/+83
| | | | | | | | | | | | | | | | | | | It's very likely that the configured data transfer mode is the wrong one if device fails data transfers right after initial data transfer mode configuration (including NCQ on/off and xfermode). libata EH needs to speed down fast before upper layers give up on probing. This patch implement fast speed down rules to handle such cases better. Error occured while data transfer hasn't been verified trigger fast back-to-back speed down actions until data transfer works. This change will make cable mis-detection and other initial configuration problems corrected before partition scanning code gives up. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: implement ATA_DFLAG_DUBIOUS_XFERTejun Heo2008-01-231-2/+31
| | | | | | | | | | | ATA_DFLAG_DUBIOUS_XFER is set whenever data transfer speed or method changes and gets cleared when data transfer command succeeds in the newly configured transfer mode. This will be used to improve speed down logic. Signed-off-by: Tejun Heo <htejun@gmail.com< Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: adjust speed down rulesTejun Heo2008-01-231-6/+6
| | | | | | | | | | | | | | | Speed down rules were too conservative. Adjust them a bit. * More than 10 timeouts can't happen in 5 minutes as command timeout is 30secs. Lower the limit for rule #1 to 6. * 10 timeouts is too high for rule #3 too. Lower it to 6. * SATAPI can benefit from falling back to PIO too. Allow SATAPI devices to fall back to PIO. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: clean up EH speed down implementationTejun Heo2008-01-231-44/+73
| | | | | | | | | | | | | | | | | | | | Clean up EH speed down implementation. * is_io boolean variable is replaced eflags. is_io is ATA_EFLAG_IS_IO. * Error categories now have names. * Better comments. * Reorder 5min and 10min rules in ata_eh_speed_down_verdict() * Use local variable @link to cache @dev->link in ata_eh_speed_down() These changes are to improve readability and ease further changes. This patch doesn't introduce any behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: move ata_set_mode() to libata-eh.cTejun Heo2008-01-231-0/+25
| | | | | | | | | Move ata_set_mode() to libata-eh.c. ata_set_mode() is surely an EH action and will be more tightly coupled with the rest of error handling. Move it to libata-eh.c. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: factor out ata_eh_schedule_probe()Tejun Heo2008-01-231-17/+21
| | | | | | | | | | | | | Factor out ata_eh_schedule_probe() from ata_eh_handle_dev_fail() and ata_eh_recover(). This is to improve maintainability and make future changes easier. In the previous revision, ata_dev_enabled() test was accidentally dropped while factoring out. This problem was spotted by Bartlomiej. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata-acpi: add ACPI _PSx methodShaohua Li2008-01-231-0/+3
| | | | | | | | | | | ACPI spec (ver 3.0a, p289) requires IDE power on/off executes ACPI _PSx methods. As recently most PATA drivers use libata, this patch adds _PSx method support in libata. ACPI spec doesn't mention if SATA requires the same _PSx method. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Acked-by: Len Brown <len.brown@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: don't normalize UNKNOWN to NONE after resetTejun Heo2008-01-101-3/+1
| | | | | | | | | | | | | | | | | | | | | After non-classifying reset, ehc->classes[] could contain ATA_DEV_UNKNOWN which used to be normalized to ATA_DEV_NONE for consistency. However, this causes unfortunate side effect for drivers which have non-classifying hardresets (e.g. sata_nv) by making hardreset report ATA_DEV_NONE for non-classifying resets and thus makes EH believe that the port is unoccupied and recovery can be skipped. The end result is that after a device is swapped with another one, the new device isn't attached after the old one is detached. This patch makes ata_eh_reset() not normalize UNKNOWN to NONE after non-classifying resets. This fixes the above problem. As UNKNOWN and NONE are handled differently by only EH hotplug logic, this doesn't cause other behavior changes. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata-pmp: propagate timeout to host linkTejun Heo2008-01-101-5/+15
| | | | | | | | Timeout on downstream command may indicate transmission problem on host link. Propagate timeouts to host link. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: update atapi_eh_request_sense() such that lbam/lbah contains buffer sizeTejun Heo2007-12-171-2/+2
| | | | | | | | While updating lbam/h for ATAPI commands, atapi_eh_request_sense() was left out. Update it. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: report protocol and full CDB on errorTejun Heo2007-12-011-9/+33
| | | | | | | | Protocol and CDB allocation size field are important in determining what went wrong with ATAPI commands. Report them on failure. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: remove unused functionsAdrian Bunk2007-11-191-95/+0
| | | | | | | | | | | This patch removes the following obsolete functions: - libata-core.c: __sata_phy_reset() - libata-core.c: sata_phy_reset() - libata-eh.c: ata_qc_timeout() - libata-eh.c: ata_eng_timeout() Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: consider errors not associated with commands for speed downTejun Heo2007-11-031-6/+13
| | | | | | | | | | | | | | | | | | | libata EH used to ignore errors not associated with commands when determining whether speed down is necessary or not. This leads to the following problems. * Errors not associated with commands can occur indefinitely without libata EH taking corrective actions. * Upstream link errors don't trigger speed down when PMP is attached to it and commands issued to downstream device trigger errors on the upstream link. This patch makes ata_eh_link_autopsy() consider errors not associated with command for speed down. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: more robust reset failure handlingTejun Heo2007-11-031-9/+16
| | | | | | | | | | | | | | | | | | Reset failure is a critical error. It results in disabling the link requiring user intervention to re-enable it. Make reset failure handling more robust such that libata EH doesn't give up too early. * Temporary glitches during hardreset may lead to classification failure when there's no softreset available. Retry instead of giving up. * Initial softreset or follow up softreset may fail classification. Move classification error handling block out of followup softreset block such that both cases are handled and retry instead of giving up. Also, on the last try, give ATA class a blind shot. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: cosmetic clean up / reorganization of ata_eh_reset()Tejun Heo2007-11-031-56/+56
| | | | | | | | | | | | Clean up and reorganize ata_eh_reset() to ease further changes. * Cache ARRAY_SIZE(ata_eh_reset_timeouts) in @max_tries. * Cache link->flags in @lflags. * Move failure handling block to the end of the function and unnest both success and failure handling blocks. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: fix timing computation in ata_eh_reset()Tejun Heo2007-11-031-1/+1
| | | | | | | | | As jiffies changes asynchronously, it needs to be cached if unchanging timestamp is needed. The code in ata_eh_reset() intended to do that with @now but never actually did it. Fix it. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: implement and use ATA_QCFLAG_QUIETTejun Heo2007-10-301-1/+3
| | | | | | | | | | | | | | | | | | | | Implement ATA_QCFLAG_QUIET which indicates that there's no need to report if the command fails with AC_ERR_DEV and set it for passthrough commands. Combined with previous changes, this now makes device errors for all direct commands reported directly to the issuer without going through EH actions and reporting. Note that EH is still invoked after non-IO device errors to determine the nature of the error and resume command execution (some controller requires special care after error to continue). It just performs default maintenance after error, examines what's going on, realizes that it's none of its business and reports the command failure without logging any error messages. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: stop being overjealous about non-IO commandsTejun Heo2007-10-301-5/+11
| | | | | | | | | | | | | | | | | | | | | | libata EH always revalidated device and retried failed command after error except for ATAPI CCs. This is unnecessary and hinders with users issuing direct commands. This patch makes the following changes. * Make sata_sil24 not request ATA_EH_REVALIDATE on device errors. sil24 is the only driver which does this. All others let libata EH core code decide. * Don't request revalidation after device error of non-IO command. Revalidation doesn't really help anybody. As ATA_EH_REVALIDATE isn't set by default, there's no reason to clear it after sense data is read. Kill ATA_EH_REVALIDATE clearing code while at it. * Don't retry non-IO command after device error. Device has rejected the command. There's no point in retrying. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] Link power management infrastructureKristen Carlson Accardi2007-10-291-0/+4
| | | | | | | | | | | | | | | | | | | | | | Device Initiated Power Management, which is defined in SATA 2.5 can be enabled for disks which support it. This patch enables DIPM when the user sets the link power management policy to "min_power". Additionally, libata drivers can define a function (enable_pm) that will perform hardware specific actions to enable whatever power management policy the user set up for Host Initiated Power management (HIPM). This power management policy will be activated after all disks have been enumerated and intialized. Drivers should also define disable_pm, which will turn off link power management, but not change link power management policy. Documentation/scsi/link_power_management_policy.txt has additional information. Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: no need to speed down if already at PIO0Tejun Heo2007-10-291-1/+1
| | | | | | | | | | | After reset, transfer mode is always PIO0 regardless of dev->xfer_mask. Check dev->pio_mode before trying to slow down after configuration failure. This prevents bogus speed down before device is actually configured. Signed-off-by: Tejun Heo <htejun@gmail.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: relocate forcing PIO0 on resetTejun Heo2007-10-291-0/+19
| | | | | | | | | | | | | | | | | | | Forcing PIO0 on reset was done inside ata_bus_softreset(), which is a bit out of place as it should be applied to all resets - hard, soft and implementation which don't use ata_bus_softreset(). Relocate it such that... * For new EH, it's done in ata_eh_reset() before calling prereset. * For old EH, it's done before calling ap->ops->phy_reset() in ata_bus_probe(). This makes PIO0 forced after all resets. Another difference is that reset itself is done after PIO0 is forced. Signed-off-by: Tejun Heo <htejun@gmail.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: track SLEEP state and issue SRST to wake it upTejun Heo2007-10-291-1/+3
| | | | | | | | | | | | | | | ATA devices in SLEEP mode don't respond to any commands. SRST is necessary to wake it up. Till now, when a command is issued to a device in SLEEP mode, the command times out, which makes EH reset the device and retry the command after that, causing a long delay. This patch makes libata track SLEEP state and issue SRST automatically if a command is about to be issued to a device in SLEEP. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Bruce Allen <ballen@gravity.phys.uwm.edu> Cc: Andrew Paprocki <andrew@ishiboo.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
OpenPOWER on IntegriCloud