summaryrefslogtreecommitdiffstats
path: root/arch
Commit message (Collapse)AuthorAgeFilesLines
* [PATCH] ppc32 8xx: fix warnings in m8xx_setup.cMarcelo Tosatti2005-08-301-3/+3
| | | | | | | The following patch fixes two warnings in arch/ppc/syslib/m8xx_setup.c Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] x86: pci_assign_unassigned_resources() updateIvan Kokshaysky2005-08-302-34/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I had some time to think about PCI assign issues in 2.6.13-rc series. The major problem here is that we call pci_assign_unassigned_resources() way too early - at subsys_initcall level. Therefore we give no chances to ACPI and PnP routines (called at fs_initcall level) to reserve their respective resources properly, as the comments in drivers/pnp/system.c and drivers/acpi/motherboard.c suggest: /** * Reserve motherboard resources after PCI claim BARs, * but before PCI assign resources for uninitialized PCI devices */ So I moved the pci_assign_unassigned_resources() call to pcibios_assign_resources() (fs_initcall), which should hopefully fix a lot of problems and make PCIBIOS_MIN_IO tweaks unnecessary. Other changes: - remove resource assignment code from pcibios_assign_resources(), since it duplicates pci_assign_unassigned_resources() functionality and actually does nothing in 2.6.13; - modify ROM assignment code as per Ben's suggestion: try to use firmware settings by default (if PCI_ASSIGN_ROMS is not set); - set CARDBUS_IO_SIZE back to 4K as it's a wonderful stress test for various setups. Confirmed by Tero Roponen <teanropo@cc.jyu.fi> (who had problems with the 4kB CardBus IO size previously). Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Remove nested feature sectionsDavid Gibson2005-08-301-3/+1
| | | | | | | | | | | | | | | The {BEGIN,END}_FTR_SECTION asm macros used in ppc64 to nop out sections of code at runtime cannot be nested. However, we do nest them in hash_low.S. We get away with it there, because there is nothing between the BEGIN markers for each section. However, that's confusing to someone reading the code. This patch removes the nested ifset and ifclr feature sections, replacing them with a single feature section in the full mask/value form. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] ppc64: lparconfig.c memory leakJoel Schopp2005-08-301-0/+1
| | | | | | | This patch fixes a rare memory leak found by Coverity. Signed-off-by: Joel Schopp <jschopp@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] ppc64: of_device.c remove useless codeJoel Schopp2005-08-301-2/+0
| | | | | | | Coverity found more unused code. Signed-off-by: Joel Schopp <jschopp@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] ppc64: Add CONFIG_HZAnton Blanchard2005-08-305-15/+15
| | | | | | | | While ppc64 has the CONFIG_HZ Kconfig option, it wasnt actually being used. Connect it up and set all platforms to 250Hz. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] oprofile PVR 970MPJake Moilanen2005-08-301-0/+1
| | | | | | | Here's the 970MP's PVR (processor version register) entry for oprofile. Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] PPC64: Don't try to claim memory from OF at 1GB markOlof Johansson2005-08-301-1/+4
| | | | | | | | | | | | | | | | | Some RS64-based machines (p620, F80, others) have problems with firmware returning 0xdeadbeef instead of failure to allocations that end at the 1GB mark. We have two options: 1. Detect the undocumented 0xdeadbeef return value and interpret it as a failure. 2. Avoid allocating that high. (2) is really the cleaner solution here. 768MB is plenty of room so use that as the max alloc_top instead of 1GB. Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] Create include/asm-powerpcStephen Rothwell2005-08-302-1/+19
| | | | | | | | | | | | | The ppc and ppc64 trees are hopefully going to merge over time, so this patch begins the process by creating a place for the merging of the header files. Create include/asm-powerpc (and move linkage.h into it from asm-{ppc,ppc64} since we don't like empty directories). Modify the ppc and ppc64 Makefiles to cope. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] Make MODULE_DEVICE_TABLE work for vio devicesStephen Rothwell2005-08-301-1/+1
| | | | | | | Make MODULE_DEVICE_TABLE work for vio devices. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] Create vio_bus_opsStephen Rothwell2005-08-303-20/+20
| | | | | | | | | | | | Create vio_bus_ops so that we just pass a structure to vio_bus_init instead of three separate function pointers. Rearrange vio.h to avoid forward references. vio.h only needs struct device_node from prom.h so remove the include and just declare it. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] Create vio_register_deviceStephen Rothwell2005-08-303-14/+18
| | | | | | | | Take some assignments out of vio_register_device_common and rename it to vio_register_device. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] Formatting changes to vio.cStephen Rothwell2005-08-301-22/+17
| | | | | | | | Formatting changes to vio.c to bring it closer to the kernel coding standard. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] fix iSeries build for gcc-3.4Stephen Rothwell2005-08-301-0/+5
| | | | | | | | | | | | | | | | | gcc 3.4 (at least the build we are using) puts the gcc generated .ident string into a .note section at the end of the files it compiles (gcc 3.3.3-hammer and gcc 4.0.2 Debian puts it in the .text section). This means that the lparmap.s file we produce in the iSeries build may end with a .note section. When we include it into head.S, the assembler can no longer resolve some of the conditional branches since the target label ends up too far away. This patch just forces us back to the .text section after including lparmap.s. The breakage was caused by my patch "iSeries build with newer assemblers and compilers" (sha1-id: 2ad56496627630ebc99f06af5f81ca23e17e014e). Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] Restore lparmap.s include for iSeriesDavid Gibson2005-08-301-1/+10
| | | | | | | | | A mistake rebasing the series of ppc64 head.S cleanup patches meant the #include of lparmap.s, needed for iSeries was lost. This patch puts it back again. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* Merge HEAD from master.kernel.org:/pub/scm/linux/kernel/git/paulus/ppc64-2.6 Linus Torvalds2005-08-2956-1822/+1920
|\
| * [PATCH] Dynamic hugepage addresses for ppc64David Gibson2005-08-293-65/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Paulus, I think this is now a reasonable candidate for the post-2.6.13 queue. Relax address restrictions for hugepages on ppc64 Presently, 64-bit applications on ppc64 may only use hugepages in the address region from 1-1.5T. Furthermore, if hugepages are enabled in the kernel config, they may only use hugepages and never normal pages in this area. This patch relaxes this restriction, allowing any address to be used with hugepages, but with a 1TB granularity. That is if you map a hugepage anywhere in the region 1TB-2TB, that entire area will be reserved exclusively for hugepages for the remainder of the process's lifetime. This works analagously to hugepages in 32-bit applications, where hugepages can be mapped anywhere, but with 256MB (mmu segment) granularity. This patch applies on top of the four level pagetable patch (http://patchwork.ozlabs.org/linuxppc64/patch?id=1936). Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: Check of_chosen in check_for_initrd()Michael Ellerman2005-08-291-8/+12
| | | | | | | | | | | | | | | | | | | | | | You can't call get_property() on a NULL node, so check if of_chosen is set in check_for_initrd(). Signed-off-by: Michael Ellerman <michael@ellerman.id.au> arch/ppc64/kernel/setup.c | 20 ++++++++++++-------- 1 files changed, 12 insertions(+), 8 deletions(-) Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: unflatten_device_tree() should check if lmb_alloc() failsMichael Ellerman2005-08-291-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | unflatten_device_tree() doesn't check if lmb_alloc() succeeds or not, it should. All it can do is panic, but at least there's an error message (assuming you have some sort of console at that point). Signed-off-by: Michael Ellerman <michael@ellerman.id.au> arch/ppc64/kernel/prom.c | 9 +++++++-- 1 files changed, 7 insertions(+), 2 deletions(-) Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: Fix a misleading printk in unflatten_dt_node()Michael Ellerman2005-08-291-1/+1
| | | | | | | | | | | | | | | | | | | | | | When unflatten_dt_node() fails to find an OF_DT_END_NODE tag it prints "Weird tag at start of node", this should be "Weird tag at end of node". Signed-off-by: Michael Ellerman <michael@ellerman.id.au> arch/ppc64/kernel/prom.c | 2 +- 1 files changed, 1 insertion(+), 1 deletion(-) Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: Move ppc64_enable_pmcs() logic into a ppc_md functionMichael Ellerman2005-08-295-50/+50
| | | | | | | | | | | | | | | | | | This patch moves power4_enable_pmcs() to arch/ppc64/kernel/pmc.c. I've tested it on P5 LPAR and P4. It does what it used to. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: allow xmon=offOlaf Hering2005-08-293-13/+25
| | | | | | | | | | | | | | | | | | | | If both CONFIG_XMON and CONFIG_XMON_DEFAULT is enabled in the .config, there is no way to disable xmon again. setup_system calls first xmon_init, later parse_early_param. So a new 'xmon=off' cmdline option will do the right thing. Signed-off-by: Olaf Hering <olh@suse.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: Remove CONFIG_MSCHUNKSMichael Ellerman2005-08-292-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | We can now remove CONFIG_MSCHUNKS as it doesn't do anything interesting anymore. The only macro in abs_addr.h which is called by non-iSeries code is phys_to_abs(), so remove the other dummy implementations, and we add a firmware feature check to phys_to_abs(). Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: Simplify some lmb functionsMichael Ellerman2005-08-291-22/+5
| | | | | | | | | | | | | | | | | | | | | | | | lmb_phys_mem_size() can always return lmb.memory.size, as long as it's called after lmb_analyze(), which it is. There's no need to recalculate the size on every call. lmb_analyze() was calculating a few things we then threw away, so just don't calculate them to start with. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: Remove physbase from the lmb_property structMichael Ellerman2005-08-294-40/+14
| | | | | | | | | | | | | | | | We no longer need the lmb code to know about abs and phys addresses, so remove the physbase variable from the lmb_property struct. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: Remove redundant abs_to_phys() macroMichael Ellerman2005-08-292-22/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | abs_to_phys() is a macro that turns out to do nothing, and also has the unfortunate property that it's not the inverse of phys_to_abs() on iSeries. The following is for my benefit as much as everyone else. With CONFIG_MSCHUNKS enabled, the lmb code is changed such that it keeps a physbase variable for each lmb region. This is used to take the possibly discontiguous lmb regions and present them as a contiguous address space beginning from zero. In this context each lmb region's base address is its "absolute" base address, and its physbase is it's "physical" address (from Linux's point of view). The abs_to_phys() macro does the mapping from "absolute" to "physical". Note: This is not related to the iSeries mapping of physical to absolute (ie. Hypervisor) addresses which is maintained with the msChunks structure. And the msChunks structure is not controlled via CONFIG_MSCHUNKS. Once upon a time you could compile for non-iSeries with CONFIG_MSCHUNKS enabled. But these days CONFIG_MSCHUNKS depends on CONFIG_PPC_ISERIES, so for non-iSeries code abs_to_phys() is a no-op. On iSeries we always have one lmb region which spans from 0 to systemcfg->physicalMemorySize (arch/ppc64/kernel/iSeries_setup.c line 383). This region has a base (ie. absolute) address of 0, and a physbase address of 0 (as calculated in lmb_analyze() (arch/ppc64/kernel/lmb.c line 144)). On iSeries, abs_to_phys(aa) is defined as lmb_abs_to_phys(aa), which finds the lmb region containing aa (and there's only one, ie. 0), and then does: return lmb.memory.region[0].physbase + (aa - lmb.memory.region[0].base) physbase == base == 0, so you're left with "return aa". So remove abs_to_phys(), and lmb_abs_to_phys() which is the implementation of abs_to_phys() for iSeries. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: Remove redundant use of pointers in lmb codeMichael Ellerman2005-08-291-57/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The lmb code is all written to use a pointer to an lmb struct. But it's always the same lmb struct, called "lmb". So we take the address of lmb, call it _lmb and then start using _lmb->foo everywhere, which is silly. This patch removes the _lmb pointers and replaces them with direct references to the one "lmb" struct. We do the same for some _mem and _rsv pointers which point to lmb.memory and lmb.reserved respectively. This patch looks quite busy, but it's basically just: s/_lmb->/lmb./g s/_mem->/lmb.memory./g s/_rsv->/lmb.reserved./g s/_rsv/&lmb.reserved/g s/mem->/lmb.memory./g Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: Remove redundant uses of physRpn_to_absRpnMichael Ellerman2005-08-293-5/+6
| | | | | | | | | | | | | | | | | | | | | | physRpn_to_absRpn is a no-op on non-iSeries platforms, remove the two redundant calls. There's only one caller on iSeries so fold the logic in there so we can get rid of it completely. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: Rename msChunks structureMichael Ellerman2005-08-292-10/+11
| | | | | | | | | | | | | | | | Rename the msChunks struct to get rid of the StUdlY caps and make it a bit clearer what it's for. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: msChunks cleanupsMichael Ellerman2005-08-292-20/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Chunks are 256KB, so use constants for the size/shift/mask, rather than getting them from the msChunks struct. The iSeries debugger (??) might still need access to the values in the msChunks struct, so we keep them around for now, but set them from the constant values. Replace msChunks_entry typedef with regular u32. Simplify msChunks_alloc() to manipulate klimit directly, rather than via a parameter. Move msChunks_alloc() and msChunks into iSeries_setup.c, as that's where they're used. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: Remove PTRRELOC() from msChunks codeMichael Ellerman2005-08-291-9/+1
| | | | | | | | | | | | | | | | | | | | | | The msChunks code was written to work on pSeries, but now it's only used on iSeries. This means there's no need to do PTRRELOC anymore, so remove it all. A few places were getting "extern reloc_offset()" from abs_addr.h, move it into system.h instead. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: introduce FW_FEATURE_ISERIESStephen Rothwell2005-08-293-2/+4
| | | | | | | | | | Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: make firmware_has_feature() strongerStephen Rothwell2005-08-297-41/+54
| | | | | | | | | | | | | | | | Make firmware_has_feature() evaluate at compile time for the non pSeries case and tidy up code where possible. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: create firmware_has_feature()Stephen Rothwell2005-08-298-11/+17
| | | | | | | | | | | | | | | | Create the firmware_has_feature() inline and move the firmware feature stuff into its own header file. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: remove firmware features from cpu_specStephen Rothwell2005-08-298-28/+14
| | | | | | | | | | | | | | | | | | | | | | The firmware_features field of struct cpu_spec should really be a separate variable as the firmware features do not depend on the chip and the bitmask is constructed independently. By removing it, we save 112 bytes from the cpu_specs array and we access the bitmask directly instead of via the cur_cpu_spec pointer. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] Move variables in ppc64 head.S from .data to .bssDavid Gibson2005-08-291-7/+6
| | | | | | | | | | | | | | | | | | | | | | The ppc64 head.S defines several zero-initialized structures, such as the empty_zero_page and the kernel top-level pagetable. Currently they are defined to be in the data section. However, they're not used until after the bss is cleared, so this patch moves them to the bss, saving two and a half pages from the vmlinux. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] Tweak comments in ppc64 head.SDavid Gibson2005-08-291-4/+4
| | | | | | | | | | | | | | | | This patch adjust some comments in head.S for accuracy, clarity, and spelling. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] Remove unneeded #defines in head.SDavid Gibson2005-08-291-11/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | arch/ppc64/kernel/head.S #defines SECONDARY_PROCESSORS then has some #ifdefs based on it. Whatever purpose this had is long lost, this patch removes it. Likewise, head.S defines H_SET_ASR, which is now defined, along with other hypervisor call numbers in hvcall.h. This patch deletes it, as well, from head.S. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] Fix apparent code overlap in ppc64 head.SDavid Gibson2005-08-291-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | An #if/#else construct near the top of ppc64's head.S appears to create overlapping sections of code for iSeries and pSeries (i.e. one thing on iSeries and something different in the same place on pSeries). In fact, checking the various absolute offsets, it doesn't. This patch unravels the #ifdefs to make it more obvious what's going on. This accomplishes another microstep towards a single kernel image which can boot both iSeries and pSeries. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] Remove general use functions from head.SDavid Gibson2005-08-292-95/+98
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As well as the interrupt vectors and initialization code, head.S contains several asm functions which are used during runtime. This patch moves these to misc.S, a more sensible location for random asm support code. A couple The functions moved are: disable_kernel_fp giveup_fpu disable_kernel_altivec giveup_altivec __setup_cpu_power3 (empty function) Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] Change address of ppc64 initial segment tableDavid Gibson2005-08-292-17/+19
| | | | | | | | | | | | | | | | | | | | On ppc64 machines with segment tables, CPU0's segment table is at a fixed address, currently 0x9000. This patch moves it to the free space at 0x6000, just below the fwnmi data area. This saves 8k of space in vmlinux and the runtime kernel image. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] Move iSeries and common vectors into unused space in head.SDavid Gibson2005-08-291-179/+174
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the ppc64 kernel head.S there is currently quite a lot of unused space between the naca (at fixed address 0x4000) and the fwnmi data area (at fixed address 0x7000). This patch moves various exception vectors and support code into this region to use the wasted space. The functions load_up_fpu and load_up_altivec are moved down as well, since they are essentially continuations of the fp_unavailable_common and altivec_unavailable_common vectors, respectively. Likewise, the fwnmi vectors themselves are moved down into this area, because while the location of the fwnmi data area is fixed by the RPA, the vectors themselves can be anywhere sufficiently low. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] Remove NACA fixed address constraintDavid Gibson2005-08-293-219/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Comments in head.S suggest that the iSeries naca has a fixed address, because tools expect to find it there. The only tool which appears to access the naca is addRamDisk, but both the in-kernel version and the version used in RHEL and SuSE in fact locate the NACA the same way as the hypervisor does, by following the pointer in the hvReleaseData structure. Since the requirement for a fixed address seems to be obsolete, this patch removes the naca from head.S and replaces it with a normal C initializer. For good measure, it removes an old version of addRamDisk.c which was sitting, unused, in the ppc32 tree. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: split pSeries specific parts out of vio.cStephen Rothwell2005-08-294-278/+281
| | | | | | | | | | | | | | This patch just splits out the pSeries specific parts of vio.c. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: make the bus matching function platform specificStephen Rothwell2005-08-292-10/+30
| | | | | | | | | | | | | | | | This patch allows us to have a different bus if matching function for each platform. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: move iSeries vio iommu initStephen Rothwell2005-08-292-4/+2
| | | | | | | | | | | | | | | | Since the iSeries vio iommu tables cannot be used until after the vio bus has been initialised, move the initialisation of the tables to there. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: split iSeries specific parts out of vio.cStephen Rothwell2005-08-293-125/+159
| | | | | | | | | | | | | | This patch splits the iSeries specific parts out of vio.c. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: change duplicate Kconfig menu "General setup" to "Bus Options"Frank Rowand2005-08-291-34/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | arch/ppc64/Kconfig defines a "General setup" menu, but also sources init/Kconfig which also defines a "General setup" menu. Both of these menus appear at the top level of make menuconfig. Having two menus with the same name is confusing. This patch renames the ppc64/Kconfig menu to be "Bus Options" and moves options in this menu which are not bus related to the end of the "Platform support" menu. There are many variations among architectures on the exact naming of the "Bus Options" menu. I chose to use the simplest one, which is also used in arch/ppc/Kconfig. Signed-off-by: Frank Rowand <frowand@mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] ppc64: PCI device-node failure detectionJake Moilanen2005-08-291-2/+17
| | | | | | | | | | | | | | | | | | | | | | | | OpenFirmware marks devices as failed in the device-tree when a hardware problem is detected. The kernel needs to fail config reads/writes to prevent a kernel crash when incorrect data is read. This patch validates that the device-node is not marked "fail" when config space reads/writes are attempted. Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] flattened device tree changesBenjamin Herrenschmidt2005-08-292-63/+200
| | | | | | | | | | | | | | | | | | This patch updates the format of the flattened device-tree passed between the boot trampoline and the kernel to support a more compact representation, for use by embedded systems mostly. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
OpenPOWER on IntegriCloud