| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This takes a bit of a sledgehammer to the machvec I/O routines. The
iomem case requires no special casing and so can just be dropped
outright. This only leaves the ioport casing for PCI and SuperIO
mangling. With the SuperIO case going through the standard ioport
mapping, it's possible to replace everything with generic routines.
With this done the standard I/O routines are tidied up and NO_IOPORT
now gets default-enabled for the vast majority of boards.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
This extends some of the existing special casing for HAS_IOPORT
platforms and gets it to the point where platforms can begin to
conditionally select it.
The major changes here are that the PIO routines themselves go away
completely, including all of the machvec port mapping wrappers. With this
in place it's possible for any non-machvec abusing platform to disable
PIO completely. At present this is left as an opt-in until the abusers
are the odd ones out instead of the majority.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |
|
|
|
|
|
|
|
| |
This plugs in a memory init callback in the machvec to permit boards to
wire up various bits of memory directly in to LMB. A generic machvec
implementation is provided that simply wraps around the normal
Kconfig-derived memory start/size.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |
|
|
|
|
|
|
| |
This fixes up the build and behaviour for various configurations. Namely
the CONFIG_32BIT cases where legacy mappings do not exist, as well as the
sh64 build.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This bumps up the default I/O base to P2SEG, which allows legacy probing
to bail out gracefully rather than oopsing. Platforms that have a real
PIO offset still need to fix this up on their own, although most
platforms are content with P2SEG already.
The previous change to teach ioport_map() about >= P1SEG offsets in
combination with this patch allows both the already remapped and the
legacy address probing to pass through and succeed.
Fixes up an oops with i8042 on the sh7785lcr board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add mode pin support for the SuperH architecture V2.
With this patch applied the board code can add their
own function to export the cpu mode pin configuration.
In most cases this will be a constant bitmap, but
boards that allow reading this from a register can
instead read out the pin state from hardware.
The code warns if a pin is tested but no board specific
mode pin function has been provided.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |
|
|
|
|
|
|
|
|
| |
This tidies up a lot of the PIO/MMIO split. No in-tree platforms were
making use of the MMIO overloading through the machvec (nor have any of
them been in some time), so we just kill all of that off. The ISA I/O
routine wrapping remains unaffected, which remains the only special
casing outside of the iomap API that boards need to think about.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |
|
|
| |
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Now that __initmv references the machvec section unconditionally
there have been cases where folks have been mistakenly flagging
non-machvec structures with the machvec section attribute (presumably
to shut up modpost). This leads to obscure breakage in earlyprintk
amongst other places and is rather non-obvious.
Add a simple sanity check to try and catch __initmv misuse and
panic early.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
This kills off the BareCPU board as a "special" machvec, rather,
we leave this as a default for when no other vector is available,
or when we want to use it in combination with other vectors for
testing with generic ops. As sh_mv is copied out anyways (or
overloaded when an alternate vector is explicitly selected), this
doesn't consume any additional memory.
The generic machvec can be forcibly selected with sh_mv=generic,
or by not having any other boards enabled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
We now throw all of the machvecs in to .machvec.init and either
select one on the command line, or copy out the first (and
usually only) one to sh_mv. The rest are freed as usual.
This gets rid of all of the silly sh_mv aliasing and makes the
selection explicit rather than link-order dependent.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
This fixes up much of the machvec handling, allowing for it to be
overloaded on boot. Making practical use of this still requires
some Kconfig munging, however.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
