summaryrefslogtreecommitdiffstats
path: root/arch/powerpc/platforms/86xx/gef_ppc9a.c
Commit message (Collapse)AuthorAgeFilesLines
* powerpc/86xx: Renaming following split of GE Fanuc joint ventureMartyn Welch2010-03-041-6/+6
| | | | | | | | This patch renames GE Fanuc boards following the split-up of the GE Fanuc joint venture. These boards are now made by GE Intelligent platorms. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Support for NVRAM on GE Fanuc's PPC9AMartyn Welch2009-11-201-0/+5
| | | | | | | Add support for NVRAM on GE Fanuc's PPC9A. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Correct reading of information presented in cpuinfoMartyn Welch2009-08-201-7/+30
| | | | | | | | | | | | | | /proc/cpuinfo should be showing the boards revision and the revision of the FPGA fitted. The functions currently used to access this information as incorrect. Additionally the VME geographical address of the PPC9A and it's status as system contoller are available in the board registers. Show these in cpuinfo. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* powerpc/86xx: clean up smp init codeKumar Gala2009-05-191-1/+0
| | | | | | | | | Removed the need for asm/mpc86xx.h as it was only used in mpc86xx_smp.c and just moved the defines it cared about into there. Also fixed up the ioremap to only map the one 4k page we need access to and to iounmap when we are done. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Move gianfar mdio nodes under the ethernet nodesAnton Vorontsov2009-03-241-0/+1
| | | | | | | | | | | | | Currently it doesn't matter where the mdio nodes are placed, but with power management support (i.e. when sleep = <> properties will take effect), mdio nodes placement will become important: mdio controller is a part of the ethernet block, so the mdio nodes should be placed correctly. Otherwise we may wrongly assume that MDIO controllers are available during sleep. Suggested-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Board support for GE Fanuc's PPC9AMartyn Welch2009-03-191-0/+223
Support for the PPC9A VME Single Board Computer from GE Fanuc (PowerPC MPC8641D). This is the basic board support for GE Fanuc's PPC9A, a 6U single board computer, based on Freescale's MPC8641D. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
OpenPOWER on IntegriCloud