summaryrefslogtreecommitdiffstats
path: root/arch/blackfin/mach-bf561/boards/ezkit.c
Commit message (Collapse)AuthorAgeFilesLines
* bf561: add capabilities in adv7183_inputsScott Jiang2012-07-241-0/+3
| | | | | | | Add capabilities in adv7183_inputs to indicate that S_STD is supported. Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
* blackfin: bf561: add adv7183 capture supportBob Liu2012-01-091-0/+95
| | | | | Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
* blackfin: i2c-lcd: change default clock rateAaron Wu2012-01-091-1/+1
| | | | | | | | Change default clock rate of GPIO based I2C operation for BF533 and BF561 to bring up the I2C interface LCD display Signed-off-by: Aaron Wu <Aaron.Wu@analog.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
* blackfin: config: update macro SPI_BFIN in board fileSonic Zhang2012-01-091-2/+2
| | | | | | | | Macro name for spi controller driver has been modified, so update default board file accordingly. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
* Blackfin: add serial TX IRQ in individual platform resourceSonic Zhang2011-11-141-1/+6
| | | | | | | | | The serial TX IRQ is not simply (RX IRQ + 1) on some Blackfin chips, so move the values to the platform resources. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Bob Liu <lliubbo@gmail.com>
* Blackfin: boards: clean up redundant/dead spi resourcesMike Frysinger2011-07-231-17/+0
| | | | | | | | | | | | The default for the Blackfin SPI driver is 8 bits and dma disabled, so many of the bfin5xx_spi_chip resources are redundant. So punt those parts. Further, drivers should themselves be declaring 16 bit transfers, so for those that do, and for the ones which no longer do 16 bit transfers, drop the bfin5xx_spi_chip resources. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: net2272: move pin setup to boards filesMike Frysinger2011-07-231-0/+24
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf548-ezkit/bf561-ezkit: update nor flash layoutMike Frysinger2011-05-251-1/+9
| | | | | | | | Both the BF548-EZKIT and the BF561-EZKIT use top boot flashes, so now that Das U-Boot uses the last small sector for its environment, update their nor layout in the kernel accordingly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: boards: add missing "static" to peripheral listsMike Frysinger2011-01-101-1/+1
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: i2c-gpio boards: use GPIO_PF# definesMike Frysinger2010-10-221-2/+2
| | | | | | Rather than use raw numbers for the GPIO pins, use proper GPIO defines. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf561-ezkit: add AD1836 codec resourcesBarry Song2010-10-221-0/+50
| | | | | | | | This board has an AD1836 codec, so make sure we have the right resources declared for it. Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: boards: use proper irq flags with isp1362-hcdMichael Hennerich2010-10-221-1/+1
| | | | | | | | | | | | With the recent kernel update the isp1362-hcd driver evaluates the IORESOURCE_IRQ resource flags and requests the irq with the given polarity/edge settings. However the ISP1362 config requires low level/edge interrupts. Most of the Blackfin boards use some random flag or no flag at all. Make all boards use a know good flag IORESOURCE_IRQ_LOWEDGE. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: boards: update AD183x resourcesBarry Song2010-10-221-6/+6
| | | | | | | Make sure we use the right Kconfig names and platform strings. Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: rename AD1836 to AD183X in board filesBarry Song2010-03-091-4/+4
| | | | | | | | The ASoC codec driver was generalized and renamed, so update the board resources accordingly. Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: add UART/SPORT early platform resourcesSonic Zhang2010-03-091-0/+15
| | | | | | | | This lets people easily select the UART/SPORT consoles for early printk while leveraging the pins declared in the boards file. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: move on-chip UART resources to boards filesSonic Zhang2010-03-091-8/+39
| | | | | | | | | | Rather than keeping the pins in the actual driver and worrying about a mess of Kconfig options, declare all the desired pin resources in the boards file. This lets people easily select the specific pins/ports for the normal UART as well as GPIOs for CTS/RTS. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: drop unused ax88180 resourcesMike Frysinger2009-12-151-26/+0
| | | | | | The ax88180 driver was never merged, so drop the corresponding resources. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: fix typo in isp1760 platform nameMichael Hennerich2009-12-151-1/+1
| | | | | | | | The driver changed from "isp1760-hcd" to "isp1760", so update resources to match. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: drop all simple-gpio board resourcesMike Frysinger2009-10-081-15/+0
| | | | | | | The simple-gpio has been replaced by the gpio sysfs interface, so drop the unused simple-gpio resources from all Blackfin boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: mass clean up of copyright/licensing infoRobin Getz2009-10-071-25/+4
| | | | | | | | | | | | | | | | | | Bill Gatliff & David Brownell pointed out we were missing some copyrights, and licensing terms in some of the files in ./arch/blackfin, so this fixes things, and cleans them up. It also removes: - verbose GPL text(refer to the top level ./COPYING file) - file names (you are looking at the file) - bug url (it's in the ./MAINTAINERS file) - "or later" on GPL-2, when we did not have that right It also allows some Blackfin-specific assembly files to be under a BSD like license (for people to use them outside of Linux). Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: delete '-spi' suffix in ad1836/ad1938 driver nameBarry Song2009-09-161-1/+1
| | | | | | | | The ASoC drivers have dropped the redundant "-spi" suffix in the driver name, so update the board resources accordingly. Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: convert boards to use platform data with smc91xMichael Hennerich2009-09-161-0/+11
| | | | | | | | Latest smc91x driver allows you to specify settings in board resources rather than needing CONFIG_BLACKFIN in the drivers/net/smc91x.h header. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: drop unused ISP1760 port1_disable from board resourcesMike Frysinger2009-06-221-1/+0
| | | | | | | The port1 disable stuff was dropped from the USB ISP1760, so update the Blackfin boards accordingly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: define SPI IRQ in board resourcesYi Li2009-06-131-0/+5
| | | | | | | | The Blackfin SPI driver can be driven by an IRQ now, so declare it in the board resources. Signed-off-by: Yi Li <yi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin arch: Modify bfin_sir device configuration to board fileGraf Yang2009-01-071-6/+18
| | | | | | Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* Blackfin arch: make ADI board names consistentMike Frysinger2008-11-181-1/+1
| | | | | | | Cc: Graf Yang <graf.yang@analog.com> Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* Blackfin arch: Enable ISP1760 USB Host Driver in platform device ↵Michael Hennerich2008-11-181-35/+28
| | | | | | | | initialization code. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* Blackfin arch: remove pata resources from generic boardMike Frysinger2008-08-051-46/+0
| | | | | | | | these are highly board specific, so putting into generic doesnt make much sense Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* Blackfin arch: be consistant with parition names, and ensure the bus is ↵Robin Getz2008-08-051-3/+3
| | | | | | | | identified Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* Blackfin arch: protect only the SPI bus controller with CONFIG_SPI_BFINMike Frysinger2008-06-071-6/+3
| | | | | | Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* [Blackfin] arch: Functional power management support: Add CPU and platform ↵Michael Hennerich2008-05-071-0/+31
| | | | | | | | voltage scaling support Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* [Blackfin] arch: add Blackfin on-chip SIR IrDA driver supportGraf Yang2008-04-251-0/+23
| | | | | | | | | - add platform device resources in board files - add new bfin_sir.h to each machines Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* [Blackfin] arch: Adjust the u-boot and kernel image partition size in mtd ↵Grace Pan2008-04-241-1/+1
| | | | | | | | device. Signed-off-by: Grace Pan <grace.pan@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* [Blackfin] arch: __FUNCTION__ is gcc-specific, use __func__Harvey Harrison2008-04-231-1/+1
| | | | | | | | | | Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* [Blackfin] arch: conditionally enable flash resources since it requests the ↵Mike Frysinger2008-03-261-0/+5
| | | | | | | | async memory bank Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* [Blackfin] arch: add board resources for new simple-gpio char driverMike Frysinger2008-02-221-0/+14
| | | | | | Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* [Blackfin] arch: fix bug - set right partition size in the board filesMike Frysinger2008-02-251-1/+1
| | | | | | | | | | | | - set default u-boot partition size to 256k - modify the offset with the size change - use mtd defines (append for offset and full for size) where applicable rather than churning constants when we dont have to Signed-off-by: Grace Pan <grace.pan@analog.com> Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* [Blackfin] arch: Encourage users to use the spidev character driver: Provide ↵Michael Hennerich2008-02-091-0/+16
| | | | | | | | | | | platform support - Enable kernel generic spidev driver for blackfin SPI ADC - spi_adc driver, document and test sample not synced Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* [Blackfin] arch: Enable NET2272 on BF561-EZkit - remove request_mem_regionMichael Hennerich2008-02-021-0/+25
| | | | | | Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* [Blackfin] arch: Add Support for ISP1362Michael Hennerich2008-02-021-0/+46
| | | | | | Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* Rename: linux/pata_platform.h to linux/ata_platform.hJeff Garzik2008-02-061-1/+1
| | | | Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [Blackfin] arch: use common flash driver to setup partitions rather than the ↵Mike Frysinger2008-01-241-0/+42
| | | | | | | | bf5xx-flash driver Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* [Blackfin] arch: enable generic GPIO based I2C driver in STAMP-BF533, ↵Bryan Wu2008-01-241-0/+24
| | | | | | | EZKIT-BF533 and EZKIT-BF561 boards Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* [Blackfin] arch: replace current blackfin specific pfbutton driver with ↵Michael Hennerich2008-01-271-0/+30
| | | | | | | | kernel generic gpio key driver Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* Blackfin arch: add AXIS AX88180 Gigabit Ethernet Hardware and Driver to ↵Michael Hennerich2007-11-171-0/+27
| | | | | | | | board files Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* Blackfin arch: move hard coded pin_req to board fileBryan Wu2007-11-121-0/+2
| | | | | | | | | | | Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time - move this static things to the blackfin board file - add pin_req array to struct bfin5xx_spi_master - tested on BF537/BF548 with SPI flash Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* Blackfin arch: use "char bfin_board_name[]" rather than "char ↵Mike Frysinger2007-10-211-1/+1
| | | | | | | | *bfin_board_name" per discussion on lkml as the former uses less storage Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* Blackfin arch: update platform driver resource information to all board filesBryan Wu2007-10-111-8/+74
| | | | | Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* Blackfin arch: cleanup warnings from checkpatch -- no functional changesMike Frysinger2007-07-121-17/+16
| | | | | | Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* Blackfin arch: move board specific setup out of common init code and into ↵Mike Frysinger2007-05-211-5/+10
| | | | | | | | the board specific init code Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OpenPOWER on IntegriCloud