| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Outer cache checked whether L2 is enabled or not. If L2 isn't enabled in XSC3,
it would enable L2. This operation is evil that would make system hang.
In XSC3 core document, these words are mentioned in below.
"Following reset, the L2 Unified Cache Enable bit is cleared. To enable the L2
Cache, software may set the bit to a '1' before or at the same time as enabling
the MMU. Enabling the L2 Cache after the MMU has been enabled or disabling the
L2 Cache after the L2 Cache has been enabled, may result in unpredictable
behavior of the processor."
When outer cache is initialized, the MMU is already enabled. We couldn't enable
L2 after MMU enabled.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On xsc3, L2 cache ops are possible only on virtual addresses. The code
is rearranged so to have a linear progression requiring the least amount
of pte setups in the highmem case. To protect the virtual mapping so
created, interrupts must be disabled currently up to a page worth of
address range.
The interrupt disabling is done in a way to minimize the overhead within
the inner loop. The alternative would consist in separate code for
the highmem and non highmem compilation which is less preferable.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When 'start' and 'end' are less than a cacheline apart and 'start' is
unaligned we are done after cleaning and invalidating the first
cacheline. So check for (start < end) which will not walk off into
invalid address ranges when (start > end).
This issue was caught by drivers/dma/dmatest.
2.6.27 is susceptible.
Cc: <stable@kernel.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
|
|
|
|
|
|
| |
Add asm/cputype.h, moving functions and definitions from asm/system.h
there. Convert all users of 'processor_id' to the more efficient
read_cpuid_id() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
(20072fd0c93349e19527dd2fa9588b4335960e62 lost most of its changes
somehow, came from a mbox archive applied with git-am. No idea
what happened. This puts back the missing bits. --rmk)
The initial patch from Lothar, and Lennert make it into a cleaner
one, modified and tested on PXA320 by Eric Miao.
This patch moves the L2 cache operations out of proc-xsc3.S into
dedicated outer cache support code.
CACHE_XSC3L2 can be deselected so no L2 cache specific code will be
linked in, and that L2 enable bit will not be set, this applies to
the following cases:
a. _only_ PXA300/PXA310 support included and no L2 cache wanted
b. PXA320 support included, but want L2 be disabled
So the enabling of L2 depends on two things:
- CACHE_XSC3L2 is selected
- and L2 cache is present
Where the latter is only a safeguard (previous testing shows it works
OK even when this bit is turned on).
IXP series of processors with XScale3 cannot disable L2 cache for the
moment since they depend on the L2 cache for its coherent memory, so
IXP may always select CACHE_XSC3L2.
Other L2 relevant bits are always turned on (i.e. the original code
enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side
effects. Specifically, these bits are:
- OC bits in TTBASE register (table walk outer cache attributes)
- LLR Outer Cache Attributes (OC) in Auxiliary Control Register
Signed-off-by: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|