summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-imx/mm-imx1.c
Commit message (Collapse)AuthorAgeFilesLines
* gpio/mxc: get rid of the uses of cpu_is_mx()Shawn Guo2011-07-081-4/+8
| | | | | | | | | | The patch removes all the uses of cpu_is_mx(). Instead, it utilizes platform_device_id to distinguish the different gpio types, IMX1_GPIO on i.mx1, IMX21_GPIO on i.mx21 and i.mx27, IMX31_GPIO on all other i.mx SoCs. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* gpio/mxc: Change gpio-mxc into an upstanding gpio driverShawn Guo2011-06-061-9/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | The patch makes necessary changes on gpio-mxc as below to turn it into an upstanding gpio driver. * Add a list to save all mx2 ports references, so that mx2_gpio_irq_handler can walk through all interrupt status registers * Use readl/writel to replace mach-specific accessors __raw_readl/__raw_writel * Change mxc_gpio_init into mxc_gpio_probe function * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to be public at all, and also make some other cleanup on plat-mxc/include/mach/gpio.h at the same time And the patch then migrates mach-imx and mach-mx5 to the updated driver by adding corresponding platform devices. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* ARM i.MX: iomux v1 initialization away from initcallSascha Hauer2011-03-071-0/+3
| | | | | | This saves us from soc level dispatching in generic files Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM i.MX: Move gpio initialization to SoC specific filesSascha Hauer2011-03-071-2/+9
| | | | | | This saves us from soc level dispatching in generic files Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: imx: use .init_early to initialize cpu type and reset addressUwe Kleine-König2011-02-101-2/+5
| | | | | | | | This used to be done in .map_io which is supposed to only setup the memory mapping. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: imx: use MXxy_IO_P2V macros to setup static mappingsUwe Kleine-König2010-11-171-6/+1
| | | | | | | | | | This makes less code rely on the virtual constants. To further simplify code and reduce the needed boilerplate when defining the static mappings a new helper macro is defined in mach/hardware.h. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* imx: move gpio init after to irq initJason Wang2010-07-261-1/+1
| | | | | | | | | | | | The commit 9a763bf "get rid of mxc_gpio_init" changed gpio_init and irq_init sequence. Usually we will call set_irq_chained_handler in gpio_init functions, this should be called after the irq_init called, otherwise the chained irq can't get propoer irq_chip and this irq will remain masked even we called set_irq_chained_handler. Signed-off-by: Jason Wang <jason77.wang@gmail.com> Tested-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: imx: remove paragraphs with old address of the FSFUwe Kleine-König2010-06-301-5/+0
| | | | | | | As the kernel contains a copy of the GPL anyhow just get rid of the address specification instead of fixing it. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* ARM: imx: move mx1 support to mach-imxUwe Kleine-König2010-06-301-0/+55
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
OpenPOWER on IntegriCloud