| Commit message (Collapse) | Author | Age | Files | Lines | |
|---|---|---|---|---|---|
| * | ARM: tegra: add SD wp-gpios to Jetson TK1 DT | Stephen Warren | 2014-04-29 | 1 | -0/+1 |
| | | | | | | | | | Jetson TK1 can detect write-protect on the SD card. Add the required DT entries to allow this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> | ||||
| * | ARM: tegra: use correct audio CODEC on Jetson TK1 | Stephen Warren | 2014-04-28 | 1 | -3/+3 |
| | | | | | | | | | | | Jetson TK1 contains an RT5639 not an RT5640. While the two are extremely similar and mostly compatible, we should still use the correct device name in the device tree. I had meant to fix this before applying the initial DT, but this issue slipped my mind. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com> | ||||
| * | ARM: tegra: jetson-tk1 - Enable HDMI support | Thierry Reding | 2014-04-28 | 1 | -2/+37 |
| | | | | | | | | | | Add HDMI +5V, VDD and PLL regulators and enable the DDC I2C controller. Enable the HDMI device, provide the power supplies as well as the DDC adapter and use pin the standard pin (PN7) for hotplug detection. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> | ||||
| * | ARM: tegra: fix Jetson TK1 SD card supply | Stephen Warren | 2014-04-16 | 1 | -1/+1 |
| | | | | | | | | | | Regulator vddio_sdmmc3 provides the Tegra<->SD IO voltage, not the card core supply voltage. That is, it provides vqmmc, not vmmc. Fix the DT to correctly reflect this. Reported-by: Andrew Bresticker <abrestic@chromium.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> | ||||
| * | ARM: tegra: define Jetson TK1 regulators | Stephen Warren | 2014-04-15 | 1 | -0/+230 |
| | | | | | | | | | | | | | | | | | | | | | These are mostly identical to the Venice2 regulator definitions, since the board designs are very similar. Differences are: - Jetson TK1 doesn't have a built-in LCD panel, so on-board regulators are not present for the backlight, touchscreen, or panel. - +3.3V_RUN needs to be boot-on/always-on, since it's widely used. This change should likely be propagated to Venice2 for completeness, although it will have no practical effect there since various other regulators use +3.3V_RUN as their supply and are always-on. - +3.3V_LP0 needs to be boot-on as well as always-on. One reason is because it's used to driver the UART level-shifter; without this, I see a brief period of UART corruption during cold boots.I suspect this change needs to be propagated to Venice2, and we simply haven't noticed the need since there's no UART level-shifter on Venice2. - A few rails have different names in the schematics. Signed-off-by: Stephen Warren <swarren@nvidia.com> | ||||
| * | ARM: tegra: add Jetson TK1 device tree | Stephen Warren | 2014-04-15 | 1 | -0/+1561 |
| Jetson TK1 is an NVIDIA Tegra124 development board, containing Tegra124, 2GB RAM, eMMC, SD card, SPI flash, serial port, PCIe Ethernet, HDMI, audio, mini PCIe, JTAG, SATA, and an expansion IO connector containing GPIOs, I2C, SPI, CSI, eDP, etc. The following features work with this device tree: UART, SD card, eMMC, SPI flash, USB (full-size jack, and mini-PCIe), audio, AS3722 RTC, system power-off, suspend/resume (LP1) with wake via RTC alarm. The following features should work with this device tree, but are not validated: Expansion I2C, expansion SPI, expansion GPIO, gpio-key for the power button. The following features are not yet implemented in this device tree: Most voltage regulators, expansion UART, HDMI, eDP, PCIe (Ethernet, and mini- PCIe connector), CSI, SATA. Signed-off-by: Stephen Warren <swarren@nvidia.com> | |||||
 |
index : op-kernel-dev | |
| Development kernel branch for OpenPOWER systems | Raptor Engineering, LLC |
| summaryrefslogtreecommitdiffstats |
|