summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
Commit message (Collapse)AuthorAgeFilesLines
* Merge tag 'sunxi-h3-h5-for-4.17' of ↵Arnd Bergmann2018-03-271-2/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard: Here is our usual bunch of changes to the common DTSI shared between arm and arm64, and their associated device trees. Even though the diffstat is quite big, it's been mostly just cleanups. The big feature is that the HDMI is now suported on H3 and H5 boards. * tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus ARM: dts: sun8i-h3: Add Mali node ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards ARM: dts: sun8i: h3: Enable HDMI output on H3 boards ARM: dts: sunxi: h3/h5: Add HDMI pipeline ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property ARM: dts: nanopi-neo-air: Add WiFi / eMMC
| * ARM: dts: sunxi: Switch MMC nodes away from cd-inverted propertyTuomas Tynkkynen2018-02-131-2/+1
| | | | | | | | | | | | | | | | | | | | Using the cd-inverted property is not useful when GPIOs are used as card detects since the polarity can be specified with the usual GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for U-Boot developers, so migrate all sunxi boards away from cd-inverted. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
* | ARM: dts: sun9i: cubieboard4: Enable VGA display outputChen-Yu Tsai2018-03-191-0/+68
|/ | | | | | | | | | | | | | | | | | | The Cubieboard4 has a dumb VGA DAC connected to the output of LCD0, providing VGA output through the onboard VGA connector. The DDC lines are connected to i2c3. The VGA DAC is a GM7123, which is compatible with Analog Devices' ADV7123, except it only takes 3.3V power, and has a lower standby power consumption. The datasheet found online lists "Chengdu GoldTel Electronical Technology Co., Ltd." as its designer. The company changed its name in 2014 to "Chengdu Corpro Technology Co., Ltd.". Their website lists similar ICs, but not actually the GM7123. Enable the display pipeline with the VGA DAC and connector, and i2c3 for DDC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
* ARM: dts: sun9i: Change node names to remove underscoresMaxime Ripard2017-10-131-1/+1
| | | | | | | Some boards have had node names with underscores. Remove them in favour of hyphens in order to reduce the DTC warnings. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: cubieboard4: Remove card detect pull-upMaxime Ripard2017-10-061-9/+1
| | | | | | | | | | The board has an external pull-up on the card-detect signal, so there's no need to add another one. This also removes a DTC warning. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: Rename pinctrl nodes to avoid warningsMaxime Ripard2017-10-061-1/+1
| | | | | | | | Our pinctrl node names were containing unit-adresses without a reg property, resulting in a warning. Change the names for our new convention. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: Remove GPIO pinctrl nodes to avoid warningsMaxime Ripard2017-10-061-15/+1
| | | | | | | | | | The A80 boards still define some GPIO pinctrl nodes that are not really useful, and redundant with the muxing already happening on gpio_request. Let's remove those nodes. This will also remove DTC warnings. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sunxi: Remove no longer used pinctrl/sun4i-a10.h headerChen-Yu Tsai2017-03-271-1/+0
| | | | | | | | | | | | | | | | | All dts files for the sunxi platform have been switched to the generic pinconf bindings. As a result, the sunxi specific pinctrl macros are no longer used. Remove the #include entry with the following command: sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \ arch/arm/boot/dts/sun?i*.* arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra empty line. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: sunxi: Convert pinctrl nodes to generic bindingsMaxime Ripard2016-12-261-9/+9
| | | | | | | | Now that we can handle the generic pinctrl bindings, convert our DT to it. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: sunxi: Remove useless allwinner,pull propertyMaxime Ripard2016-12-261-2/+0
| | | | | | | | | | | | The allwinner,pull property set to NO_PULL was really considered our default (and wasn't even changing the default value in the code). Remove these properties to make it obvious that we do not set anything in such a case. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: sunxi: Remove useless allwinner,drive propertyMaxime Ripard2016-12-261-3/+0
| | | | | | | | | The allwinner,drive property set to 10mA was really considered as our default. Remove all those properties entirely to make that obvious. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: dts: sun9i: cubieboard4: Enable AP6330 WiFiChen-Yu Tsai2016-11-221-0/+32
| | | | | | | | | | The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with the enabling pin connected to PL2. The AC100 RTC provides a low power clock signal. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulatorsChen-Yu Tsai2016-09-211-0/+112
| | | | | | | | | The AXP806 PMIC is the secondary PMIC. It provides various supply voltages for the SoC and other peripherals. The PMIC's interrupt line is connected to NMI pin of the SoC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unusedChen-Yu Tsai2016-09-211-0/+4
| | | | | | | | The AXP809's SW (switch) regulator is unused on the Cubieboard 4. Add an empty node for it so that the OS can generate constraints. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: Switch to the AC100 RTC clock outputs for osc32kChen-Yu Tsai2016-08-221-0/+5
| | | | | | | | | | | The 32.768 kHz clock inside the A80 SoC is fed from an external source, typically the AC100 RTC module. Make the osc32k placeholder a fixed-factor clock so board dts files can specify its source. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: cubieboard4: Add device node for AC100Chen-Yu Tsai2016-08-221-0/+24
| | | | | Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: cubieboard4: Order nodes by alphabetical orderChen-Yu Tsai2016-07-041-16/+16
| | | | | | | Move the &pio node below the mmc nodes for proper ordering by name. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: cubieboard4: Drop sunxi-common-regulators.dtsiChen-Yu Tsai2016-07-041-1/+0
| | | | | | | | | | | | sunxi-common-regulators.dtsi provided dummy regulators vcc3v0, vcc3v3, vcc5v0. 3.0V/3.3V and 5.0V are commonly used voltages in Allwinner devices. These dummy regulators provide a stand-in when bindings that require one, but the real regulator is not supported yet. Since these are no longer needed, we can drop the include file. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulatorsChen-Yu Tsai2016-07-041-2/+129
| | | | | | | | | The AXP809 PMIC is the primary PMIC. It provides various supply voltages for the SoC and other peripherals. The PMIC's interrupt line is connected to NMI pin of the SoC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: cubieboard4: Enable hardware reset and HS-DDR for eMMCChen-Yu Tsai2016-01-251-0/+6
| | | | | | | | | | | | mmc2 has a special pin for eMMC hardware reset, which is controllable from the controller. Add the "mmc-cap-hw-reset" property to denote that this controller supports this function, and the pins are actually used. Also increase the signal drive strength for mmc2 pins, for HS-DDR mode support. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: cubieboard4: Enable Reduced Serial Bus controllerChen-Yu Tsai2015-12-101-0/+4
| | | | | | | | The Reduced Serial Bus (RSB) controller is used to talk to the 3 companion ICs (2 PMICs, 1 RTC/codec IC) on the board. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: cubieboard4: Enable consumer IR receiverChen-Yu Tsai2015-12-101-0/+4
| | | | | | | The Cubieboard4 has a consumer IR receiver. Enable it in the DT. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: sun9i: cubieboard4: Enable LEDsChen-Yu Tsai2015-12-101-0/+22
| | | | | | | The Cubieboard4 has 2 controllable LEDs, 1 red and 1 green. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* ARM: dts: add cubietech cubieboard4Tyler Baker2015-04-271-0/+99
Add a Cubietech Cubieboard4 device tree and instruct make to build it. This device tree has been derived from the sun9i-a80-optimus.dts as they are very similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM definitions will need to be updated in the future. [1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdf Signed-off-by: Tyler Baker <tyler.baker@linaro.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
OpenPOWER on IntegriCloud