summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
Commit message (Collapse)AuthorAgeFilesLines
* ARM: ux500: move GPIO key configuration to device treeLinus Walleij2013-11-261-0/+5
| | | | | | | | | | This moves over the configuration of the GPIO keys (used for proximity sensor and Hall effect sensor) from the static pin configuration file to the device tree. As part of the exercise, implement the GPIO keys properly in a per-UIB file as this setup actually differs with each UIB. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: ux500: move SKE pin config to device treeLinus Walleij2013-11-261-0/+7
| | | | | | | | | | | | This moves the SKE keypad pin control table out of the board file and into the device tree. This was previously set to be active on all MOP500 and HREF boards but after reading the schematic this seems incorrect: the HREFv60 and later uses one of these for MC5 and no reference designs have the SKE connected to any hardware so just leave the pins alone in the power-on state. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: ux500: move SPI pin config to device treeLinus Walleij2013-11-261-0/+31
| | | | | | | | | | This moves the SPI pin control table out of the board file and into the device tree. Move the specific setting for SSP0 on the HREFprev60 into the prev60-specific DTS file. The SPI2 configuration is not really connected to any device, as it will conflict with GPIO218 which is used on all HREFs. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: ux500: move MUSB pin config to device treeLinus Walleij2013-11-261-0/+13
| | | | | | | | This moves the MUSB pin control table out of the board file and into the device tree. Tie the config to the on-chip MUSB device rather than the ab8500-usb device which is off-chip. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: ux500: move GPIO217/218 config to device treeLinus Walleij2013-11-261-0/+5
| | | | | | | | | This moves the input-pulled-up setting for GPIO217 as used on the HREFs prior to v60 from the boardfile to the device tree. GPIO218 is only used with the TVK UIB so move it to that .dtsi file. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: ux500: move MMC/SD/SDIO pin control to the device treeLinus Walleij2013-11-261-0/+19
| | | | | | | | | | | | This moves the static, device-tied pin control configuration out of the board file board-mop500-pins.c and into the device tree. Add entries for SDI1 and SDI2 on the Snowball so that the WLAN pins on SDI1 can be used further on, and the unused pins on SDI2 can be put to sleep. Cc: Lee Jones <lee.jones@linaro.org> Cc: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: u8540: Add Pinctrl Device Tree settings for uart0, uart2Gabriel Fernandez2013-08-061-0/+95
This patch adds pinctrl device tree settings for uart0 and uart2 for ccu8540 board. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OpenPOWER on IntegriCloud