summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* bnx2: Report MDI/MDIX status to ethtool.Michael Chan2014-01-012-0/+20
| | | | | Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Enable auto-mdix when autoneg is disabled.Michael Chan2014-01-012-3/+15
| | | | | | | | | Auto-mdix currently only works if autoneg is enabled. This patch enables auto-mdix all the time by setting a bit in a PHY register. Define meaningful constants for this PHY registers. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Advertise nothing when speed is forcedMichael Chan2014-01-011-11/+13
| | | | | | | | | | | The current code does not reset the advertisement register when the speed is forced, leaving the default advertisement value of 10 Mbps. This does not work with some link partners when the next patch enables auto-mdix. Set advertisement register to 0 if the speed is forced. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'addr_compare'David S. Miller2013-12-3125-47/+46
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ding Tianhong says: ==================== slight optimization of addr compare for net modules This is the second patchset for slight optimization of address compare, mainly for net tree, just following the Joe's opinion, it will help review the code for maintainers and supports. v2: Change some style for patch 2. According Eric's suggestion, use the ether_addr_equal_64bits to instead of ether_addr_equal for patch 19. In fact, there are a lot of places which could use ether_addr_equal_64bits to instead of ether_addr_equal, but not this time, thanks for Joe's opinion. v3: Change some style for patch 11/19: (net: packetengines: slight optimization of addr compare). Joe pointed out that is_broadcast_ether_addr(addr) would be appropriate here, but this should be left alone and not in this patch, so fix it later. In the patch (net: caif: slight optimization of addr compare), the operand for memcmp is not mac address, so it is unsuitable to use the ether_addr_equal to compare a non mac address, so remove the patch from the series. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: plip: slight optimization of addr comparedingtianhong2013-12-311-2/+2
| | | | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal_64bits to instead of memcmp. Cc: "David S. Miller" <davem@davemloft.net> Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: fddi: slight optimization of addr comparedingtianhong2013-12-311-1/+2
| | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: ti: slight optimization of addr comparedingtianhong2013-12-311-1/+1
| | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: sun: optimization of addr comparedingtianhong2013-12-311-1/+1
| | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: seeq: slight optimization of addr comparedingtianhong2013-12-311-1/+1
| | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: renesas: slight optimization of addr comparedingtianhong2013-12-311-1/+1
| | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: qlcnic: slight optimization of addr comparedingtianhong2013-12-313-6/+6
| | | | | | | | | | | | | | | | | | | | Use the possibly more efficient ether_addr_equal or ether_addr_equal_unaligned to instead of memcmp. Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: netxen: slight optimization of addr comparedingtianhong2013-12-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: Manish Chopra <manish.chopra@qlogic.com> Cc: Sony Chacko <sony.chacko@qlogic.com> Cc: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: packetengines: slight optimization of addrdingtianhong2013-12-311-7/+10
| | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: vxge: slight optimization of addr comparedingtianhong2013-12-311-1/+1
| | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: Jon Mason <jdmason@kudzu.us> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: ksz884x: slight optimization of addr comparedingtianhong2013-12-311-5/+4
| | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: mlx4: slight optimization of addr comparedingtianhong2013-12-312-3/+3
| | | | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: Amir Vadai <amirv@mellanox.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Acked-By: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: ixgbe: slight optimization of addr comparedingtianhong2013-12-311-2/+1
| | | | | | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: igbvf: slight optimization of addr comparedingtianhong2013-12-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Carolyn Wyborny <carolyn.wyborny@intel.com> Cc: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: benet: slight optimization of addr comparedingtianhong2013-12-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: Sathya Perla <sathya.perla@emulex.com> Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com> Cc: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: enic: slight optimization of addr comparedingtianhong2013-12-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: Christian Benvenuti <benve@cisco.com> Cc: Sujith Sankar <ssujith@cisco.com> Cc: Govindarajulu Varadarajan <govindarajulu90@gmail.com> Cc: Neel Patel <neepatel@cisco.com> Cc: Nishank Trivedi <nistrive@cisco.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Acked-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: cxgb3: slight optimization of addr comparedingtianhong2013-12-312-2/+2
| | | | | | | | | | | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: Santosh Raspatur <santosh@chelsio.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: bnx2x: slight optimization of addr comparedingtianhong2013-12-313-8/+6
| | | | | | | | | | | | | | | | | | | | Use the possibly more efficient ether_addr_equal or ether_addr_equal_unaligned to instead of memcmp. Cc: Ariel Elior <ariele@broadcom.com> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: 3com: slight optimization of addr comparedingtianhong2013-12-311-2/+1
|/ | | | | | | | | Use possibly more efficient ether_addr_equal to instead of memcmp. Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net, sch: fix the typo in register_qdisc()Zhi Yong Wu2013-12-311-1/+1
| | | | | Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net, rps: fix the comment of net_rps_action_and_irq_enable()Zhi Yong Wu2013-12-311-1/+1
| | | | | Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net, rps: fix build failure when CONFIG_RPS isn't setZhi Yong Wu2013-12-311-0/+4
| | | | | | | | | | | | In file included from net/socket.c:99:0: include/net/sock.h: In function ‘sock_rps_record_flow’: include/net/sock.h:849:30: error: ‘const struct sock’ has no member named ‘sk_rxhash’ include/net/sock.h: In function ‘sock_rps_reset_flow’: include/net/sock.h:854:29: error: ‘const struct sock’ has no member named ‘sk_rxhash’ Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sctp: move skb_dst_set() a bit downwards in sctp_packet_transmit()wangweidong2013-12-311-2/+2
| | | | | | | | | | | | | skb_dst_set will use dst, if dst is NULL although is not a problem, then goto the 'no_route' and free nskb, so do the skb_dst_set is pointless. so move the skb_dst_set after dst check. Remove the unnecessary initialization as well. v2: fix the subject line because it would confuse people, as pointed out by Daniel. Signed-off-by: Wang Weidong <wangweidong1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sch_netem: support of 64bit ratesYang Yingliang2013-12-312-2/+14
| | | | | | | | | Add a new attribute to support 64bit rates so that tc can use them to break the 32bit limit. Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* sch_netem: more precise length of packetsYang Yingliang2013-12-311-1/+1
| | | | | | | | | | | With TSO/GSO/GRO packets, skb->len doesn't represent a precise amount of bytes on wire. This patch replace skb->len with qdisc_pkt_len(skb) which is more precise. Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunnelingOr Gerlitz2013-12-315-2/+129
| | | | | | | | | | | | | | | | | | | | | When the device tunneling offloads mode is vxlan do the following - call SET_PORT with the relevant setting - add DMFS steering vxlan rule for the device self and multicast mac addresses of the form: {<ETH, outer-mac> <VXLAN, ANY vnid> <ETH, ANY mac>} --> RSS QP - set relevant QPC fields in RSS context and RX ring QPs - in TX flow, set WQE fields to generate HW checksum, and handle gso skbs which are marked for encapsulation such that the HW will segment them properly. - in RX flow, read HW offloaded checksum for encapsulated packets from the CQE - advertize hw_enc_features and NETIF_F_GSO_UDP_TUNNEL to the networking stack Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Add basic support for TCP/IP offloads under tunnelingOr Gerlitz2013-12-318-4/+133
| | | | | | | | | | | | | | | Add the low-level device commands and definitions used for TCP/IP HW offloads of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC. This is done through the following elements: - read tunneling device caps in QUERY_DEV_CAP - add helper function to do SET_PORT for tunneling - add DMFS VXLAN steering rule definitions - add CQE and WQE checksum offload field definitions Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netlink: specify netlink packet direction for nlmonDaniel Borkmann2013-12-312-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In order to facilitate development for netlink protocol dissector, fill the unused field skb->pkt_type of the cloned skb with a hint of the address space of the new owner (receiver) socket in the notion of "to kernel" resp. "to user". At the time we invoke __netlink_deliver_tap_skb(), we already have set the new skb owner via netlink_skb_set_owner_r(), so we can use that for netlink_is_kernel() probing. In normal PF_PACKET network traffic, this field denotes if the packet is destined for us (PACKET_HOST), if it's broadcast (PACKET_BROADCAST), etc. As we only have 3 bit reserved, we can use the value (= 6) of PACKET_FASTROUTE as it's _not used_ anywhere in the whole kernel and not supported anywhere, and packets of such type were never exposed to user space, so there are no overlapping users of such kind. Thus, as wished, that seems the only way to make both PACKET_* values non-overlapping and therefore device agnostic. By using those two flags for netlink skbs on nlmon devices, they can be made available and picked up via sll_pkttype (previously unused in netlink context) in struct sockaddr_ll. We now have these two directions: - PACKET_USER (= 6) -> to user space - PACKET_KERNEL (= 7) -> to kernel space Partial `ip a` example strace for sa_family=AF_NETLINK with detected nl msg direction: syscall: direction: sendto(3, ...) = 40 /* to kernel */ recvmsg(3, ...) = 3404 /* to user */ recvmsg(3, ...) = 1120 /* to user */ recvmsg(3, ...) = 20 /* to user */ sendto(3, ...) = 40 /* to kernel */ recvmsg(3, ...) = 168 /* to user */ recvmsg(3, ...) = 144 /* to user */ recvmsg(3, ...) = 20 /* to user */ Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Jakub Zawadzki <darkjames-ws@darkjames.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
* netlink: only do not deliver to tap when both sides are kernel sksDaniel Borkmann2013-12-311-5/+8
| | | | | | | | | | | | We should also deliver packets to nlmon devices when we are in netlink_unicast_kernel(), and only one of the {src,dst} sockets is user sk and the other one kernel sk. That's e.g. the case in netlink diag, netlink route, etc. Still, forbid to deliver messages from kernel to kernel sks. Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Jakub Zawadzki <darkjames-ws@darkjames.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'sctp_logspam'David S. Miller2013-12-312-12/+25
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Neil Horman says: ==================== sctp: Consolidate and ratelimit deprecation warnings The SCTP protocol has several deprecation warnings in its setsockopt path that can be triggered by unprivlidged users. Since these are not ratelimited, we can spam the logs quite easily here. Since these are all deprecation warnings, and that type of warning isn't uncommon in the rest of the kernel, lets make a common pr_warn_deprecated macro to produce somewhat generalized ratelimited deprecation warnings easily ==================== Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * SCTP: Reduce log spamming for sctp setsockoptNeil Horman2013-12-311-12/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | During a recent discussion regarding some sctp socket options, it was noted that we have several points at which we issue log warnings that can be flooded at an unbounded rate by any user. Fix this by converting all the pr_warns in the sctp_setsockopt path to be pr_warn_ratelimited. Note there are several debug level messages as well. I'm leaving those alone, as, if you turn on pr_debug, you likely want lots of verbosity. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Vlad Yasevich <vyasevich@gmail.com> CC: David Miller <davem@davemloft.net> CC: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
| * printk: Add a DEPRECATED macroNeil Horman2013-12-311-0/+7
|/ | | | | | | | | | | | | sctp has several points in its setsockopt path in which it issues deprecation warnings. It seems like it might be handy to macrotize such a warning so other subsystems can use it easily Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org> CC: "David S. Miller" <davem@davemloft.net> CC: linux-kernel@vger.kernel.org CC: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
* sch_dsmark: use correct func name in print messagesYang Yingliang2013-12-311-18/+19
| | | | | | | | | | | In dsmark_drop(), the function name printed by pr_debug is "dsmark_reset", correct it to "dsmark_drop" by using __func__ . BTW, replace the other function names with __func__ . Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sch_htb: use /* commentsYang Yingliang2013-12-311-3/+4
| | | | | | | Do not use C99 // comments and correct a spelling typo. Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net_sched: replace pr_warning with pr_warnYang Yingliang2013-12-314-13/+11
| | | | | | | Prefer pr_warn(... to pr_warning(... Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* packet: fix "foo * bar" and "(foo*)" problemsWeilong Chen2013-12-311-2/+2
| | | | | | | | Cleanup checkpatch errors.Specially,the second changed line is exactly 80 columns long. Signed-off-by: Weilong Chen <chenweilong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: unneccessary to get address prefix in addrconf_get_prefix_routeLi RongQing2013-12-311-4/+1
| | | | | | | | | | Since addrconf_get_prefix_route inputs the address prefix to fib6_locate, which does not uses the data which is out of the prefix_len length, so do not need to use ipv6_addr_prefix to get address prefix. Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'tun_rfs'David S. Miller2013-12-312-6/+49
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zhi Yong Wu says: ==================== tun: add the RFS support Since Tom Herbert's hash related patchset was modified and got merged, his pachset about adding support for RFS on tun flows also need to get adjusted accordingly. I tried to update them, and before i will start to do some perf tests, i hope to get one correct code base, so it's time to post them out now. Any constructive comments are welcome, thanks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * tun: Add support for RFS on tun flowsTom Herbert2013-12-311-2/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support so that the rps_flow_tables (RFS) can be programmed using the tun flows which are already set up to track flows for the purposes of queue selection. On the receive path (corresponding to select_queue and tun_net_xmit) the rxhash is saved in the flow_entry. The original code only does flow lookup in select_queue, so this patch adds a flow lookup in tun_net_xmit if num_queues == 1 (select_queue is not called from dev_queue_xmit->netdev_pick_tx in that case). The flow is recorded (processing CPU) in tun_flow_update (TX path), and reset when flow is deleted. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: Allow setting sock flow hash without a sockTom Herbert2013-12-311-4/+14
|/ | | | | | | | | | | | | | This patch adds sock_rps_record_flow_hash and sock_rps_reset_flow_hash which take a hash value as an argument and sets the sock_flow_table accordingly. This allows the table to be populated in cases where flow is being tracked outside of a sock structure. sock_rps_record_flow and sock_rps_reset_flow call this function where the hash is taken from sk_rxhash. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bonding: update Documentation/networking/bonding.txt for option lp_intervaldingtianhong2013-12-311-0/+8
| | | | | Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bonding: ust micro BOND_NO_USE_ARP to simplify the mode checkdingtianhong2013-12-311-12/+2
| | | | | | | The bond 3ad and TLB/ALB has the same check path, so combine them. Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bonding: add option lp_interval for loading moduledingtianhong2013-12-311-1/+12
| | | | | | | | The bond driver could set the lp_interval when loading module. Suggested-by: Scott Feldman <sfeldma@cumulusnetworks.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* lro: remove dead codestephen hemminger2013-12-292-196/+0
| | | | | | | Remove leftover code that is not used anywhere in current tree. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* bonding: make local function staticstephen hemminger2013-12-292-2/+1
| | | | | | | bond_xmit_slave_id is only used in main. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* tcp: make local functions staticstephen hemminger2013-12-293-5/+2
| | | | | | | | | The following are only used in one file: tcp_connect_init tcp_set_rto Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
OpenPOWER on IntegriCloud