summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* net/rds: zero last byte for strncpyChen Gang2013-03-081-0/+1
| | | | | | | | | | | | for NUL terminated string, need be always sure '\0' in the end. additional info: strncpy will pads with zeroes to the end of the given buffer. should initialise every bit of memory that is going to be copied to userland Signed-off-by: Chen Gang <gang.chen@asianux.com> Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Fix SFP+ misconfiguration in iSCSI boot scenarioYaniv Rosner2013-03-082-1/+6
| | | | | | | | | | Fix a problem in which iSCSI-boot installation fails when switching SFP+ boot port and moving the SFP+ module prior to boot. The SFP+ insertion triggers an interrupt which configures the SFP+ module wrongly before interface is loaded. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Fix intermittent long KR2 link up timeYaniv Rosner2013-03-082-1/+13
| | | | | | | | | | | | | When a KR2 device is connected to a KR link-partner, sometimes it requires disabling KR2 for the link to come up. To get a KR2 link up later, in case no base pages are seen, the KR2 is restored. The problem was that some link partners cleared their advertised BP/NP after around two seconds, causing the driver to disable/enable KR2 link all the time. The fix was to wait at least 5 seconds before checking KR2 recovery. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* macvlan: Set IFF_UNICAST_FLT flag to prevent unnecessary promisc mode.Vlad Yasevich2013-03-071-0/+1
| | | | | | | | | | Macvlan already supports hw address filters. Set the IFF_UNICAST_FLT so that it doesn't needlesly enter PROMISC mode when macvlans are stacked. Signed-of-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* team: unsyc the devices addresses when port is removedVlad Yasevich2013-03-071-0/+2
| | | | | | | | | | When a team port is removed, unsync all devices addresses that may have been synched to the port devices. CC: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: add missing vid to br_mdb_get()Cong Wang2013-03-074-5/+6
| | | | | | | | | | | | Obviously, vid should be considered when searching for multicast group. Cc: Vlad Yasevich <vyasevic@redhat.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Acked-by: Vlad Yasevich <vyasevich@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Fix: sparse warning in inet_csk_prepare_forced_closeChristoph Paasch2013-03-071-0/+1
| | | | | | | | | | | | In e337e24d66 (inet: Fix kmemleak in tcp_v4/6_syn_recv_sock and dccp_v4/6_request_recv_sock) I introduced the function inet_csk_prepare_forced_close, which does a call to bh_unlock_sock(). This produces a sparse-warning. This patch adds the missing __releases. Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be> Signed-off-by: David S. Miller <davem@davemloft.net>
* afkey: fix a typoJunwei Zhang2013-03-071-4/+4
| | | | | Signed-off-by: Martin Zhang <martinbj2008@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* MAINTAINERS: Update qlcnic maintainers listSony Chacko2013-03-071-0/+2
| | | | | Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netlabel: correctly list all the static label mappingsPaul Moore2013-03-071-6/+6
| | | | | | | | | | | When we have a large number of static label mappings that spill across the netlink message boundary we fail to properly save our state in the netlink_callback struct which causes us to repeat the same listings. This patch fixes this problem by saving the state correctly between calls to the NetLabel static label netlink "dumpit" routines. Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mv643xx_eth: fix for disabled autonegPhil Sutter2013-03-071-4/+51
| | | | | | | | | | When autoneg has been disabled in the PHY (Marvell 88E1118 here), auto negotiation between MAC and PHY seem non-functional anymore. The only way I found to workaround this is to manually configure the MAC with the settings sent to the PHY earlier. Signed-off-by: Phil Sutter <phil.sutter@viprinet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bonding: fire NETDEV_RELEASE event only on 0 slavesVeaceslav Falico2013-03-071-2/+3
| | | | | | | | | | Currently, if we set up netconsole over bonding and release a slave, netconsole will stop logging on the whole bonding device. Change the behavior to stop the netconsole only when the last slave is released. Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vxlan: fix oops when delete netns containing vxlanZang MingJie2013-03-071-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following script will produce a kernel oops: sudo ip netns add v sudo ip netns exec v ip ad add 127.0.0.1/8 dev lo sudo ip netns exec v ip link set lo up sudo ip netns exec v ip ro add 224.0.0.0/4 dev lo sudo ip netns exec v ip li add vxlan0 type vxlan id 42 group 239.1.1.1 dev lo sudo ip netns exec v ip link set vxlan0 up sudo ip netns del v where inspect by gdb: Program received signal SIGSEGV, Segmentation fault. [Switching to Thread 107] 0xffffffffa0289e33 in ?? () (gdb) bt #0 vxlan_leave_group (dev=0xffff88001bafa000) at drivers/net/vxlan.c:533 #1 vxlan_stop (dev=0xffff88001bafa000) at drivers/net/vxlan.c:1087 #2 0xffffffff812cc498 in __dev_close_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:1299 #3 0xffffffff812cd920 in dev_close_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:1335 #4 0xffffffff812cef31 in rollback_registered_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:4851 #5 0xffffffff812cf040 in unregister_netdevice_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:5752 #6 0xffffffff812cf1ba in default_device_exit_batch (net_list=0xffff88001f2e7e18) at net/core/dev.c:6170 #7 0xffffffff812cab27 in cleanup_net (work=<optimized out>) at net/core/net_namespace.c:302 #8 0xffffffff810540ef in process_one_work (worker=0xffff88001ba9ed40, work=0xffffffff8167d020) at kernel/workqueue.c:2157 #9 0xffffffff810549d0 in worker_thread (__worker=__worker@entry=0xffff88001ba9ed40) at kernel/workqueue.c:2276 #10 0xffffffff8105870c in kthread (_create=0xffff88001f2e5d68) at kernel/kthread.c:168 #11 <signal handler called> #12 0x0000000000000000 in ?? () #13 0x0000000000000000 in ?? () (gdb) fr 0 #0 vxlan_leave_group (dev=0xffff88001bafa000) at drivers/net/vxlan.c:533 533 struct sock *sk = vn->sock->sk; (gdb) l 528 static int vxlan_leave_group(struct net_device *dev) 529 { 530 struct vxlan_dev *vxlan = netdev_priv(dev); 531 struct vxlan_net *vn = net_generic(dev_net(dev), vxlan_net_id); 532 int err = 0; 533 struct sock *sk = vn->sock->sk; 534 struct ip_mreqn mreq = { 535 .imr_multiaddr.s_addr = vxlan->gaddr, 536 .imr_ifindex = vxlan->link, 537 }; (gdb) p vn->sock $4 = (struct socket *) 0x0 The kernel calls `vxlan_exit_net` when deleting the netns before shutting down vxlan interfaces. Later the removal of all vxlan interfaces, where `vn->sock` is already gone causes the oops. so we should manually shutdown all interfaces before deleting `vn->sock` as the patch does. Signed-off-by: Zang MingJie <zealot0630@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vmxnet3: prevent div-by-zero panic when ring resizing uninitialized devBhavesh Davda2013-03-073-2/+9
| | | | | | | | | | | Linux is free to call ethtool ops as soon as a netdev exists when probe finishes. However, we only allocate vmxnet3 tx/rx queues and initialize the rx_buf_per_pkt field in struct vmxnet3_adapter when the interface is opened (UP). Signed-off-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'mlx4'David S. Miller2013-03-0712-59/+75
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Or Gerlitz says: ==================== Here's a batch of fixes to the mlx4 core and ethernet drivers for 3.9 The commit that disabled RFS when running in SRIOV mode fixes a regression which was introduced in 3.9-rc1 but actually present also in the 3.8 -stable series. It turns out that a slightly different fix is needed there and we will generate and submit it there. Patches done against net commit 66d29cbc59433 "benet: Wait f/w POST until timeout" ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * net/mlx4_en: Disable RFS when running in SRIOV modeAmir Vadai2013-03-071-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 37706996 "mlx4_en: fix allocation of CPU affinity reverse-map" fixed a bug when mlx4_dev->caps.comp_pool is larger from the device rx rings, but introduced a regression. When the mlx4_core is activating its "legacy mode" (e.g when running in SRIOV mode) w.r.t to EQs/IRQs usage, comp_pool becomes zero and we're crashing on divide by zero alloc_cpu_rmap. Fix that by enabling RFS only when running in non-legacy mode. Reported-by: Yan Burman <yanb@mellanox.com> Cc: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net/mlx4_en: Cleanup MAC resources on module unload or port stopYan Burman2013-03-071-16/+20
| | | | | | | | | | | | | | | | | | | | | | | | Make sure we cleanup all MAC related resources (entries in the port MAC table and steering rules) when stopping a port or when the driver is unloaded. The leak was introduced by commit 07cb4b0a "net/mlx4_en: Manage hash of MAC addresses per port". Signed-off-by: Yan Burman <yanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net/mlx4_en: Fix race when setting the device MAC addressYan Burman2013-03-072-22/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove unnecessary use of workqueue for the device MAC address setting flow, and fix a race when setting MAC address which was introduced by commit c07cb4b0a "net/mlx4_en: Manage hash of MAC addresses per port" The race happened when mlx4_en_replace_mac was being executed in parallel with a successive call to ndo_set_mac_address, e.g witn an A/B/A MAC setting configuration test, the third set fails. With this change we also properly report an error if set MAC fails. Signed-off-by: Yan Burman <yanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net/mlx4_core: Fix endianness bug in set_param_lJack Morgenstein2013-03-078-18/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The set_param_l function assumes casting a u64 pointer to a u32 pointer allows to access the lower 32bits, but it results in writing the upper 32 bits on big endian systems. The fixed function reads the upper 32 bits of the 64 argument, and or's them with the 32 bits of the 32-bit value passed to the function. Since this is now a "read-modify-write" operation, we got many "unintialized variable" warnings which needed to be fixed as well. Reported-by: Alexander Schmidt <alexschm@de.ibm.com>. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net/mlx4_core: Turn off device-managed FS bit in dev-cap wrapper if DMFS is ↵Jack Morgenstein2013-03-071-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | not enabled Older kernels detect DMFS (device-managed flow steering) from the HCA device capability directly, regardless of whether the capability was enabled in INIT_HCA, this is fixed by commit 7b8157bed "mlx4_core: Adjustments to Flow Steering activation logic for SR-IOV" To protect against guests running kernels without this fix, the host driver should turn off the DMFS capability bit in mlx4_QUERY_DEV_CAP_wrapper. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net/mlx4_core: Disable mlx4_QP_ATTACH calls from guests if the host uses ↵Jack Morgenstein2013-03-071-0/+3
|/ | | | | | | | | | | | flow steering Guests kernels may not correctly detect if DMFS (device-enabled flow steering) is activated by the host. If DMFS is activated, the master should return error to guests which try to use the B0-steering flow calls (mlx4_QP_ATTACH). Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of git://1984.lsi.us.es/nfDavid S. Miller2013-03-073-7/+14
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pablo Neira Ayuso says: ==================== The following patchset contains Netfilter fixes for your net tree, they are: * Don't generate audit log message if audit is not enabled, from Gao Feng. * Fix logging formatting for packets dropped by helpers, by Joe Perches. * Fix a compilation warning in nfnetlink if CONFIG_PROVE_RCU is not set, from Paul Bolle. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * netfilter: nfnetlink: silence warning if CONFIG_PROVE_RCU isn't setPaul Bolle2013-03-041-6/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit c14b78e7decd0d1d5add6a4604feb8609fe920a9 ("netfilter: nfnetlink: add mutex per subsystem") building nefnetlink.o without CONFIG_PROVE_RCU set, triggers this GCC warning: net/netfilter/nfnetlink.c:65:22: warning: ‘nfnl_get_lock’ defined but not used [-Wunused-function] The cause of that warning is, in short, that rcu_lockdep_assert() compiles away if CONFIG_PROVE_RCU is not set. Silence this warning by open coding nfnl_get_lock() in the sole place it was called, which allows to remove that function. Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
| * netfilter: xt_AUDIT: only generate audit log when audit enabledGao feng2013-03-041-0/+3
| | | | | | | | | | | | | | | | We should stop generting audit log if audit is disabled. Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
| * netfilter: nf_ct_helper: Fix logging for dropped packetsJoe Perches2013-03-021-1/+10
| | | | | | | | | | | | | | Update nf_ct_helper_log to emit args along with the format. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* | Merge branch 'intel'David S. Miller2013-03-072-61/+34
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Jeff Kirsher says: ==================== This series contains updates to e1000e only. All three patches come from Konstantin Khlebnikov to resolve power management issues. The first patch removes redundant and unbalanced pci_disable_device() from the shutdown function. The second patch removes redundant actions from the driver and fixes the interaction with actions in pci-bus runtime power management code. The third and last patch fixes some messages like 'Error reading PHY register' and 'Hardware Erorr' and saves several seconds on reboot. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * | e1000e: fix accessing to suspended deviceKonstantin Khlebnikov2013-03-072-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes some annoying messages like 'Error reading PHY register' and 'Hardware Erorr' and saves several seconds on reboot. Cc: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Borislav Petkov <bp@suse.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * | e1000e: fix runtime power management transitionsKonstantin Khlebnikov2013-03-071-60/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch removes redundant actions from driver and fixes its interaction with actions in pci-bus runtime power management code. It removes pci_save_state() from __e1000_shutdown() for normal adapters, PCI bus callbacks pci_pm_*() will do all this for us. Now __e1000_shutdown() switches to D3-state only quad-port adapters, because they needs quirk for clearing false-positive error from downsteam pci-e port. pci_save_state() now called after clearing bus-master bit, thus __e1000_resume() and e1000_io_slot_reset() must set it back after restoring configuration space. This patch set get_link_status before calling pm_runtime_put() in e1000_open() to allow e1000_idle() get real link status and schedule first runtime suspend. This patch also enables wakeup for device if management mode is enabled (like for WoL) as result pci_prepare_to_sleep() would setup wakeup without special actions like custom 'enable_wakeup' sign. Cc: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Borislav Petkov <bp@suse.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * | e1000e: fix pci-device enable-counter balanceKonstantin Khlebnikov2013-03-071-1/+1
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch removes redundant and unbalanced pci_disable_device() from __e1000_shutdown(). pci_clear_master() is enough, device can go into suspended state with elevated enable_cnt. Bug was introduced in commit 23606cf5d1192c2b17912cb2ef6e62f9b11de133 ("e1000e / PCI / PM: Add basic runtime PM support (rev. 4)") in v2.6.35 Cc: Bruce Allan <bruce.w.allan@intel.com> CC: Stable <stable@kernel.org> Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Borislav Petkov <bp@suse.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | tun: add a missing nf_reset() in tun_net_xmit()Eric Dumazet2013-03-061-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Dave reported following crash : general protection fault: 0000 [#1] SMP CPU 2 Pid: 25407, comm: qemu-kvm Not tainted 3.7.9-205.fc18.x86_64 #1 Hewlett-Packard HP Z400 Workstation/0B4Ch RIP: 0010:[<ffffffffa0399bd5>] [<ffffffffa0399bd5>] destroy_conntrack+0x35/0x120 [nf_conntrack] RSP: 0018:ffff880276913d78 EFLAGS: 00010206 RAX: 50626b6b7876376c RBX: ffff88026e530d68 RCX: ffff88028d158e00 RDX: ffff88026d0d5470 RSI: 0000000000000011 RDI: 0000000000000002 RBP: ffff880276913d88 R08: 0000000000000000 R09: ffff880295002900 R10: 0000000000000000 R11: 0000000000000003 R12: ffffffff81ca3b40 R13: ffffffff8151a8e0 R14: ffff880270875000 R15: 0000000000000002 FS: 00007ff3bce38a00(0000) GS:ffff88029fc40000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00007fd1430bd000 CR3: 000000027042b000 CR4: 00000000000027e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process qemu-kvm (pid: 25407, threadinfo ffff880276912000, task ffff88028c369720) Stack: ffff880156f59100 ffff880156f59100 ffff880276913d98 ffffffff815534f7 ffff880276913db8 ffffffff8151a74b ffff880270875000 ffff880156f59100 ffff880276913dd8 ffffffff8151a5a6 ffff880276913dd8 ffff88026d0d5470 Call Trace: [<ffffffff815534f7>] nf_conntrack_destroy+0x17/0x20 [<ffffffff8151a74b>] skb_release_head_state+0x7b/0x100 [<ffffffff8151a5a6>] __kfree_skb+0x16/0xa0 [<ffffffff8151a666>] kfree_skb+0x36/0xa0 [<ffffffff8151a8e0>] skb_queue_purge+0x20/0x40 [<ffffffffa02205f7>] __tun_detach+0x117/0x140 [tun] [<ffffffffa022184c>] tun_chr_close+0x3c/0xd0 [tun] [<ffffffff8119669c>] __fput+0xec/0x240 [<ffffffff811967fe>] ____fput+0xe/0x10 [<ffffffff8107eb27>] task_work_run+0xa7/0xe0 [<ffffffff810149e1>] do_notify_resume+0x71/0xb0 [<ffffffff81640152>] int_signal+0x12/0x17 Code: 00 00 04 48 89 e5 41 54 53 48 89 fb 4c 8b a7 e8 00 00 00 0f 85 de 00 00 00 0f b6 73 3e 0f b7 7b 2a e8 10 40 00 00 48 85 c0 74 0e <48> 8b 40 28 48 85 c0 74 05 48 89 df ff d0 48 c7 c7 08 6a 3a a0 RIP [<ffffffffa0399bd5>] destroy_conntrack+0x35/0x120 [nf_conntrack] RSP <ffff880276913d78> This is because tun_net_xmit() needs to call nf_reset() before queuing skb into receive_queue Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'for-davem' of ↵David S. Miller2013-03-0621-381/+299
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless John W. Linville says: ==================== This time just passing along a big batch of fixes from Johannes... For the mac80211 bits: "Here I have fixes from Ben Greear for stray work items when deleting interfaces, another idle handling fix from Felix, a fix from Marco ro a mesh PS buffering crash and I have a fix for the VHT MCS calculation in association request frames and more nl80211 feature advertising removal as well as a workaround to increase the dump size if the SKB overhead is too large. For 3.10 I already have a complete fix queued, but that also requires (simple) userspace changes." And for the iwlwifi bits: "The patches from Dor fix a bunch of calibration issues in the new MVM driver, and Emmanuel has a number of fixes there as well. Also, we decided to disable 8k A-MSDU by default, so that's in there. My own patches are addressing an issue we found with the new devices but that seems to also exist on older ones, the DMA writeback the devices do can be delayed and cause issues. The fix is unfortunately relatively large and depends on two other changes (to not be hugely conflicting), but I think it's still worth it at this point." As Johannes says, it is a bit large. But I hope it is still early enough in the cycle to make that worthwhile. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * \ Merge branch 'master' of ↵John W. Linville2013-03-0621-381/+299
| |\ \ | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
| | * \ Merge branch 'for-john' of ↵John W. Linville2013-03-0415-339/+229
| | |\ \ | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
| | | * | iwlwifi: mvm: don't warn on normal BAR sendingEmmanuel Grumbach2013-03-041-5/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This flow happens when we get a failed single Tx response on an AMPDU queue. In this case, the frame won't be sent any more. So we need to move the window on the recipient side. This is done by a BAR. Now if we are in the following case: 10, 12 and 13 are ACKed and 11 isn't. 10 11 12 13. V X V V Then, 11 will be sent 16 times as an MPDU (as oppsed to A-MPDU). If this failed, we are entering the flow described above. So we need to send a BAR with ssn = 12. But in this case, the scheduler will tell us to free frames up to 13 (included). So, it is perfectly possible to get a failed single Tx response on an AMPDU queue that makes the scheduler's ssn jump by more than 1 single packet. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | iwlwifi: mvm: update the rssi calculationEmmanuel Grumbach2013-03-043-23/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make the rssi more accurate by taking in count per-chain AGC values. Without this, the RSSI reports inaccurate values. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | iwlwifi: mvm: ignore STOP_AGG when restartingEmmanuel Grumbach2013-03-041-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the device is being restarted, all the Rx / Tx Block Ack sessions are been wiped out by the driver. So ignore the requests from mac80211 that stops Tx agg while reconfiguring the device. Note that stopping a non-existing Rx BA session is harmless, so just honor mac80211's request. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | iwlwifi: mvm: Remove overriding calibrations for the 7000 familyDor Shaish2013-03-041-114/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fix removes the override of calibration request values sent to the FW. Due to that, the sending of default values to now implemented calibrations is removed. Signed-off-by: Dor Shaish <dor.shaish@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | iwlwifi: mvm: Take the phy_cfg from the TLV valueDor Shaish2013-03-041-15/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The phy_cfg is given from the TLV value and does not have to be built by us. Signed-off-by: Dor Shaish <dor.shaish@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | iwlwifi: mvm: Set valid TX antennas value before calib requestDor Shaish2013-03-041-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We must set the valid TX antennas number in the ucode before sending the phy_cfg_cmd and request for calibrations. Signed-off-by: Dor Shaish <dor.shaish@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | iwlwifi: mvm: restart the NIC of the cmd queue gets fullEmmanuel Grumbach2013-03-041-5/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This situation is clearly an error situation and the only way to recover is to restart the driver / fw. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | iwlwifi: use coherent DMA memory for command headerJohannes Berg2013-02-285-142/+137
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Recently in commit 8a964f44e01ad3bbc208c3e80d931ba91b9ea786 ("iwlwifi: always copy first 16 bytes of commands") we fixed the problem that the hardware writes back to the command and that could overwrite parts of the data that was still needed and would thus be corrupted. Investigating this problem more closely we found that this write-back isn't really ordered very well with respect to other DMA traffic. Therefore, it sometimes happened that the write-back occurred after unmapping the command again which is clearly an issue and could corrupt the next allocation that goes to that spot, or (better) cause IOMMU faults. To fix this, allocate coherent memory for the first 16 bytes of each command, containing the write-back part, and use it for all queues. All the dynamic DMA mappings only need to be TO_DEVICE then. This ensures that even when the write-back happens "too late" it can't hit memory that has been freed or a mapping that doesn't exist any more. Since now the actual command is no longer modified, we can also remove CMD_WANT_HCMD and get rid of the DMA sync that was necessary to update the scratch pointer. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | iwlwifi: disable 8K A-MSDU by defaultEmmanuel Grumbach2013-02-282-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Supporting 8K A-MSDU means that we need to allocate order 1 pages for every Rx packet. Even when there is no traffic. This adds stress on the memory manager. The handling of compound pages is also less trivial for the memory manager and not using them will make the allocation code run faster although I didn't really measure. Eric also pointed out that having huge buffers with little data in them is not very nice towards the TCP stack since the truesize of the skb is huge. This doesn't allow TCP to have a big Rx window. See https://patchwork.kernel.org/patch/2167711/ for details. Note that very few vendors will actually send A-MSDU. Disable this feature by default. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | iwlwifi: rename IWL_MAX_CMD_TFDS to IWL_MAX_CMD_TBS_PER_TFDJohannes Berg2013-02-283-11/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The IWL_MAX_CMD_TFDS name for this constant is wrong, the constant really indicates how many TBs we can use in the driver for a single command TFD, rename the constant and also add a comment explaining it. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | iwlwifi: don't map complete commands bidirectionallyJohannes Berg2013-02-281-22/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The reason we mapped them bidirectionally was that not doing so had caused IOMMU exceptions, due to the fact that the HW writes back into the command. Now that the first part of the command including the write-back part is always in the first buffer, we don't need to map the remaining buffer(s) bidi and can get rid of the special-casing for commands. This is a requisite patch for another one to fix DMA mapping. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | * | | Merge branch 'for-john' of ↵John W. Linville2013-03-046-42/+70
| | |\ \ \ | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
| | | * | | mac80211: another fix for idle handling in monitor modeFelix Fietkau2013-03-021-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When setting a monitor interface up or down, the idle state needs to be recalculated, otherwise the hardware will just stay in its previous idle state. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | | mac80211: fix VHT MCS calculationJohannes Berg2013-03-011-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VHT MCSes we advertise to the AP were supposed to be restricted to the AP, but due to a bug in the logic mac80211 will advertise rates to the AP that aren't even supported by the local device. To fix this skip any adjustment if the NSS isn't supported at all. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | | mac80211: fix oops on mesh PS broadcast forwardingMarco Porsch2013-03-011-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Introduced with de74a1d9032f4d37ea453ad2a647e1aff4cd2591 "mac80211: fix WPA with VLAN on AP side with ps-sta". Apparently overwrites the sdata pointer with non-valid data in the case of mesh. Fix this by checking for IFTYPE_AP_VLAN. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | | nl80211: increase wiphy dump size dynamicallyJohannes Berg2013-03-011-5/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Given a device with many channels capabilities the wiphy information can still overflow even though its size in 3.9 was reduced to 3.8 levels. For new userspace and kernel 3.10 we're going to implement a new "split dump" protocol that can use multiple messages per wiphy. For now though, add a workaround to be able to send more information to userspace. Since generic netlink doesn't have a way to set the minimum dump size globally, and we wouldn't really want to set it globally anyway, increase the size only when needed, as described in the comments. As userspace might not be prepared for large buffers, we can only use 4k. Also increase the size for the get_wiphy command. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | | * | | mac80211: really fix monitor mode channel reportingJohannes Berg2013-02-281-8/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After Felix's patch it was still broken in case you used more than just a single monitor interface. Fix it better now. Reported-by: Sujith Manoharan <sujith@msujith.org> Tested-by: Sujith Manoharan <sujith@msujith.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
OpenPOWER on IntegriCloud