summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* vxge: Fixed crash in PAE system due to wrong typecasting.Sreenivasa Honnur2009-10-061-1/+1
| | | | | | | | | | - Fix a crash in PAE system due to wrong typecasting. - On PAE system size_t is unsigned int which is 32bit. Avoid casting 64 bit address to 32 bit Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vxge: Removed accessing non-supported registers.Sreenivasa Honnur2009-10-062-6/+0
| | | | | | | | | | - Removed accessing GENDMA_INT register - This allowed the firmware to perform a generic DMA write to host memory. This feature is not supported by the ASIC, this patch removes access to GENDMA_INT register. Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vxge: Update driver_config->vpath_per_dev for each function in probe.Sreenivasa Honnur2009-10-061-1/+2
| | | | | | | | | | | - Update driver_config->vpath_per_dev for each function in probe. - vpath_per_device specifies number of vpaths supported for each function/device. The current code was updating vpath_per_device only for physical device, however this has to be updated for each function also in case of a MF(Multi function) device. Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vxge: Modify __vxge_hw_device_is_privilaged() to not assume function-0 as ↵Sreenivasa Honnur2009-10-061-22/+30
| | | | | | | | | | | | | | | | the privileged function: Resubmit#1 - vxge driver was assuming function-0 is always the privilaged function. Now that restriction has been removed any function can act as a privilaged function. - This patch modifies the __vxge_hw_device_is_privilaged routine to not assume function-0 as the privileged function. - Recreated the patch by incorporating review comments from Dave Miller to remove double slash in path names. Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: add flushes between RAR writes when setting mac addressAlexander Duyck2009-10-061-0/+7
| | | | | | | | | | | There are some switches that will do write combining when they see two sequential regions written. In order to avoid any possible write combining issues it is necessary to add a flush after writing each piece of a rar register. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: add additional error handling to the phy codeAlexander Duyck2009-10-061-14/+25
| | | | | | | | | | | This update adds additional exception handling to the phy code to handle situations where it may be called incorrectly. In addition it adds some bounds checking to the cable length checks to prevent an array overrun in the event that the hardware returned a different value than expected. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: add code to retry a phy read in the event of failure on link checkAlexander Duyck2009-10-061-2/+8
| | | | | | | | | | This patch adds a retry to phy reads in the event of failure. The original code broke out of the loop on failure and this is a mistake as we should be trying to do the read twice. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: move the generic copper link setup code into e1000_phy.cAlexander Duyck2009-10-063-41/+62
| | | | | | | | | | This patch moves the generic portion of the copper link setup into a seperate function in e1000_phy.c. This helps to reduce the size of copper_link_setup_82575 and make it a bit more readable. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: remove microwire support from igbAlexander Duyck2009-10-062-36/+3
| | | | | | | | | igb doesn't have any devices that use a microwire interface for NVM. As such the code related to this can be removed. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: change how we handle alternate mac addressesAlexander Duyck2009-10-063-10/+22
| | | | | | | | | | | | This patch allows us to treat the alternate mac address as though it is the physical address on the adapter. This is accomplished by letting the alt_mac_address function to only fail on an NVM error. If no errors occur and the alternate mac address is not present then RAR0 is read as the default mac address. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: fix a few items where weren't correctly setup for mbx timeoutAlexander Duyck2009-10-061-5/+14
| | | | | | | | | | The mailbox timeout routines need to be updated as they were not correctly handling the case of a mailbox timeout and could cause issues with long delays when used. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: add function to handle mailbox lockAlexander Duyck2009-10-061-29/+34
| | | | | | | | | | Both the read and write mailbox functions need to acquire the mailbox lock. Since that is the case we might as well combine both of the procedures into one function so it is easier to maintain. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: add support for 82576NS SerDes adapterAlexander Duyck2009-10-063-0/+3
| | | | | | | | | This patch adds the device ID necessary to support the 82576NS SerDes adapter. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: make use of the uta to allow for promiscous mode filterAlexander Duyck2009-10-064-47/+163
| | | | | | | | | | | | | | In order to support functions such as vlan tag stripping when SR-IOV is enabled any given packet must match at least one filter. However in the case of promiscous mode being enabled on the PF the traffic routed to it may not match any filters and is just sent to the PF by default. In order to make certain that this traffic is processed we can set all bits in the UTA registers to create a pseudo promiscous mode filter that accepts all packets. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: add combined function for setting rar and pool bitsAlexander Duyck2009-10-061-23/+40
| | | | | | | | | This patch adds igb_rar_qsel which sets the mac address and pool bits for a given mac address in the receive address register table. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: add locking to reads of the i2c interfaceAlexander Duyck2009-10-063-65/+119
| | | | | | | | | | | | The current implementation of sgmii support isn't correctly locking the interfaces for reads/writes. This change pulls the read/write functionality out of 82575.c and moves it to phy.c. In addition it replaces the implementation in 82575.c with one that uses locking around the relocated i2c interface calls. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: update the approach taken to acquiring and releasing the phy lockAlexander Duyck2009-10-061-4/+7
| | | | | | | | | | The current approach is just using a ?: type mechanism to set the phy locking bit. This if fine for now but limits us to only 2. Switch to a nested if statement for future compatiblity with more than 2 phys. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: update comments for serdes config and update to handle duplexAlexander Duyck2009-10-063-17/+40
| | | | | | | | | This update corrects the driver so that it handles duplex for serdes links correctly instead of just forcing full duplex always. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: remove unused temp variable from stats clearing pathAlexander Duyck2009-10-062-88/+84
| | | | | | | | | | There is a temp variable in the stats clearing path that isn't needed since the results from the stats read can be immediately discared. Since it isn't needed we might as well just drop it from the function call. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: export device speed and duplex via sysfsAndy Gospodarek2009-10-051-0/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch exports the link-speed (in Mbps) and duplex of an interface via sysfs. This eliminates the need to use ethtool just to check the link-speed. Not requiring 'ethtool' and not relying on the SIOCETHTOOL ioctl should be helpful in an embedded environment where space is at a premium as well. NOTE: This patch also intentionally allows non-root users to check the link speed and duplex -- something not possible with ethtool. Here's some sample output: # cat /sys/class/net/eth0/speed 100 # cat /sys/class/net/eth0/duplex half # ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised auto-negotiation: No Speed: 100Mb/s Duplex: Half Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off Supports Wake-on: g Wake-on: g Current message level: 0x000000ff (255) Link detected: yes Signed-off-by: David S. Miller <davem@davemloft.net>
* cfg80211: assign device type in netdev notifier callbackMarcel Holtmann2009-10-052-5/+7
| | | | | | | | | Instead of having to modify every non-mac80211 for device type assignment, do this inside the netdev notifier callback of cfg80211. So all drivers that integrate with cfg80211 will export a proper device type. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: introduce NETDEV_POST_INIT notifierJohannes Berg2009-10-052-0/+7
| | | | | | | | | | | | For various purposes including a wireless extensions bugfix, we need to hook into the netdev creation before before netdev_register_kobject(). This will also ease doing the dev type assignment that Marcel was working on for cfg80211 drivers w/o touching them all. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* usbnet: Set device type for wlan and wwan devicesMarcel Holtmann2009-10-051-0/+14
| | | | | | | | | For usbnet devices with FLAG_WLAN and FLAG_WWAN set the proper device type so that uevent contains the correct value. This then allows an easy identification of the actual underlying technology of the Ethernet device. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* usbnet: Use wwan%d interface name for mobile broadband devicesMarcel Holtmann2009-10-053-6/+18
| | | | | | | | | Add support for usbnet based devices like CDC-Ether to indicate that they are actually mobile broadband devices. In that case use wwan%d as default interface name. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* tunnels: Optimize tx pathEric Dumazet2009-10-054-9/+12
| | | | | | | | | | | | | | | We currently dirty a cache line to update tunnel device stats (tx_packets/tx_bytes). We better use the txq->tx_bytes/tx_packets counters that already are present in cpu cache, in the cache line shared with txq->_xmit_lock This patch extends IPTUNNEL_XMIT() macro to use txq pointer provided by the caller. Also &tunnel->dev->stats can be replaced by &dev->stats Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv4: fib table algorithm performance improvementStephen Hemminger2009-10-055-56/+48
| | | | | | | | | | The FIB algorithim for IPV4 is set at compile time, but kernel goes through the overhead of function call indirection at runtime. Save some cycles by turning the indirect calls to direct calls to either hash or trie code. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* af_packet: add interframe drop cmsg (v6)Neil Horman2009-10-052-0/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add Ancilliary data to better represent loss information I've had a few requests recently to provide more detail regarding frame loss during an AF_PACKET packet capture session. Specifically the requestors want to see where in a packet sequence frames were lost, i.e. they want to see that 40 frames were lost between frames 302 and 303 in a packet capture file. In order to do this we need: 1) The kernel to export this data to user space 2) The applications to make use of it This patch addresses item (1). It does this by doing the following: A) Anytime we drop a frame for which we would increment po->stats.tp_drops, we also no increment a stats called po->stats.tp_gap. B) Every time we successfully enqueue a frame to sk_receive_queue, we record the value of po->stats.tp_gap in skb->mark. skb->cb would nominally be the place to record this, but since all the space there is used up, we're overloading skb->mark. Its safe to do since any enqueued packet is guaranteed to be unshared at this point, and skb->mark isn't used for anything else in the rx path to the application. After we record tp_gap in the skb, we zero po->stats.tp_gap. This allows us to keep a counter of the number of frames lost between any two enqueued packets C) When the application goes to dequeue a frame from the packet socket, we look at skb->mark for that frame. If it is non-zero, we add a cmsg chunk to the msghdr of level SOL_PACKET and type PACKET_GAPDATA. Its a 32 bit integer that represents the number of frames lost between this packet and the last previous frame received. Note there is a chance that if there is frame loss after a receive, and then the socket is closed, some gap data might be lost. This is covered by the use of the PACKET_AUXDATA socket option, which gives total loss data. With a bit of math, the final gap can be determined that way. I've tested this patch myself, and it works well. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> include/linux/if_packet.h | 2 ++ net/packet/af_packet.c | 33 +++++++++++++++++++++++++++++++++ 2 files changed, 35 insertions(+) Signed-off-by: David S. Miller <davem@davemloft.net>
* TI DaVinci EMAC: Minor macro related updateschaithrika@ti.com2009-10-051-15/+11
| | | | | | | | Use BIT for macro definitions wherever possible, remove unused and redundant macros. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* pktgen: Avoid dirtying skb->users when txq is fullEric Dumazet2009-10-051-4/+7
| | | | | | | | | We can avoid two atomic ops on skb->users if packet is not going to be sent to the device (because hardware txqueue is full) Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* icmp: No need to call sk_write_space()Eric Dumazet2009-10-051-0/+4
| | | | | | | | | | | | | | | | | We can make icmp messages tx completion callback a litle bit faster. Setting SOCK_USE_WRITE_QUEUE sk flag tells sock_wfree() to not call sk_write_space() on a socket we know no thread is posssibly waiting for write space. (on per cpu kernel internal icmp sockets only) This avoids the sock_def_write_space() call and read_lock(&sk->sk_callback_lock)/read_unlock(&sk->sk_callback_lock) calls as well. We avoid three atomic ops. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethtool: Remove support for obsolete string query operationsBen Hutchings2009-10-052-52/+10
| | | | | | | | The in-tree implementations have all been converted to get_sset_count(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Convert ethtool {get_stats, self_test}_count() ops to get_sset_count()Ben Hutchings2009-10-056-55/+70
| | | | | | | | | | | | | These string query operations were supposed to be replaced by the generic get_sset_count() starting in 2007. Convert the remaining implementations. Also remove calls to these operations to initialise drvinfo->n_stats. The ethtool core code already does that. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* tehuti: Convert ethtool get_stats_count() ops to get_sset_count()Ben Hutchings2009-10-051-15/+12
| | | | | | | | | | | | This string query operation was supposed to be replaced by the generic get_sset_count() starting in 2007. Convert tehuti's implementation. Also remove the dummy self-test name which was not used since tehuti does not advertise any self-tests. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: Convert ethtool get_stats_count() ops to get_sset_count()Ben Hutchings2009-10-054-7/+12
| | | | | | | | | This string query operation was supposed to be replaced by the generic get_sset_count() starting in 2007. Convert qeth's implementation. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Linux 2.6.32-rc3v2.6.32-rc3Linus Torvalds2009-10-041-1/+1
| | | | | | | I'm skipping -rc2 because the -rc1 Makefile mistakenly said -rc2, so in order to avoid confusion, I'm jumping from -rc1 to -rc3. That way, when 'uname' (or an oops report) says 2.6.32-rc2, there's no confusion about whether people perhaps meant -rc1 or -rc2.
* headers: remove sched.h from poll.hAlexey Dobriyan2009-10-0426-1/+27
| | | | | Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'acpi-pad' of ↵Linus Torvalds2009-10-044-0/+535
|\ | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6 * 'acpi-pad' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: acpi_pad: build only on X86 ACPI: create Processor Aggregator Device driver Fixup trivial conflicts in MAINTAINERS file.
| * acpi_pad: build only on X86Len Brown2009-09-271-0/+1
| | | | | | | | | | | | X86_FEATURE_MWAIT doesn't exist on ia64... Signed-off-by: Len Brown <len.brown@intel.com>
| * ACPI: create Processor Aggregator Device driverShaohua Li2009-07-314-0/+535
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ACPI 4.0 created the logical "processor aggregator device" as a mechinism for platforms to ask the OS to force otherwise busy processors to enter (power saving) idle. The intent is to lower power consumption to ride-out transient electrical and thermal emergencies, rather than powering off the server. On platforms that can save more power/performance via P-states, the platform will first exhaust P-states before forcing idle. However, the relative benefit of P-states vs. idle states is platform dependent, and thus this driver need not know or care about it. This driver does not use the kernel's CPU hot-plug mechanism because after the transient emergency is over, the system must be returned to its normal state, and hotplug would permanently break both cpusets and binding. So to force idle, the driver creates a power saving thread. The scheduler will migrate the thread to the preferred CPU. The thread has max priority and has SCHED_RR policy, so it can occupy one CPU. To save power, the thread will invoke the deep C-state entry instructions. To avoid starvation, the thread will sleep 5% of the time time for every second (current RT scheduler has threshold to avoid starvation, but if other CPUs are idle, the CPU can borrow CPU timer from other, which makes the mechanism not work here) Vaidyanathan Srinivasan has proposed scheduler enhancements to allow injecting idle time into the system. This driver doesn't depend on those enhancements, but could cut over to them when they are available. Peter Z. does not favor upstreaming this driver until the those scheduler enhancements are in place. However, we favor upstreaming this driver now because it is useful now, and can be enhanced over time. Signed-off-by: Shaohua Li <shaohua.li@intel.com> NACKed-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Len Brown <len.brown@intel.com>
* | Merge branch 'sfi-release' of ↵Linus Torvalds2009-10-041-4/+13
|\ \ | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-sfi-2.6 * 'sfi-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-sfi-2.6: SFI: remove __init from sfi_verify_table SFI: fix section mismatch warnings in sfi_core.c
| * | SFI: remove __init from sfi_verify_tableArjan van de Ven2009-10-031-1/+1
| | | | | | | | | | | | | | | | | | | | | sfi_verify_table() is called at runtime, and thus cannot be __init Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
| * | SFI: fix section mismatch warnings in sfi_core.cRakib Mullick2009-10-031-3/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The function sfi_map_memory/sfi_unmap_memory uses early_ioremap/early_iounmap respectively, which refers to a __init function. And function sfi_check_table also refers to a __init function sfi_verify_table. Since the references are valid, so use __ref to get rid of the warnings. We were warned by the following warnings: LD vmlinux.o MODPOST vmlinux.o WARNING: vmlinux.o(.text+0xb6ba3a): Section mismatch in reference from the function sfi_map_memory() to the function .init.text:early_ioremap() The function sfi_map_memory() references the function __init early_ioremap(). This is often because sfi_map_memory lacks a __init annotation or the annotation of early_ioremap is wrong. WARNING: vmlinux.o(.text+0xb6bab6): Section mismatch in reference from the function sfi_unmap_memory() to the function .init.text:early_iounmap() The function sfi_unmap_memory() references the function __init early_iounmap(). This is often because sfi_unmap_memory lacks a __init annotation or the annotation of early_iounmap is wrong. WARNING: vmlinux.o(.text+0xb6be30): Section mismatch in reference from the function sfi_check_table() to the function .init.text:sfi_verify_table() The function sfi_check_table() references the function __init sfi_verify_table(). This is often because sfi_check_table lacks a __init annotation or the annotation of sfi_verify_table is wrong. Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
* | | Merge branch 'release' of ↵Linus Torvalds2009-10-046-103/+112
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: ACPI: EC: Don't parse DSDT for EC early init on Compal ACPI: EC: Rewrite DMI checks ACPI: dock: fix "sibiling" typo ACPI: kill overly verbose "throttling states" log messages ACPI: Fix bound checks for copy_from_user in the acpi /proc code ACPI: fix bus scanning memory leaks ACPI: EC: Restart command even if no interrupts from EC sony-laptop: Don't unregister the SPIC driver if it wasn't registered sony-laptop: remove _INI call at init time sony-laptop: SPIC unset IRQF_SHARED, set IRQF_DISABLED sony-laptop: remove device_ctrl and the SPIC mini drivers
| * \ \ Merge branch 'misc' into releaseLen Brown2009-10-033-15/+10
| |\ \ \
| | * | | ACPI: dock: fix "sibiling" typoAlex Chiang2009-10-031-8/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Crossword clues as haikus: Snakes from the same brood fighting Jackson on a plane? sibilant siblings I guess Will Shortz's job is still secure. Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
| | * | | ACPI: kill overly verbose "throttling states" log messagesRoland Dreier2009-10-031-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I was recently lucky enough to get a 64-CPU system. The processors actually have T-states, so my kernel log ends up with 64 lines like: ACPI: Processor [CPU0] (supports xx throttling states) This is pretty useless clutter because - this info is already available after boot from /proc/acpi/processor/CPUnn/throttling - there's also an ACPI_DEBUG_PRINT() in processor_throttling.c that gives the same info on boot for anyone who *really* cares. So just delete the code that prints the throttling states in processor_core.c. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
| | * | | ACPI: Fix bound checks for copy_from_user in the acpi /proc codeArjan van de Ven2009-10-031-0/+2
| | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ACPI /proc write() code takes an unsigned length argument like any write() function, but then assigned it to a *signed* integer called "len". Only after this is a sanity check for len done to make it not larger than 4. Due to the type change a len < 0 is in principle also possible; this patch adds a check for this. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
| * | | Merge branch 'bugzilla-14081' into releaseLen Brown2009-10-031-6/+46
| |\ \ \
| | * | | ACPI: EC: Don't parse DSDT for EC early init on CompalAlexey Starikovskiy2009-10-031-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Compal DSDT breaks if scanned early, while we need early scan for almost all ASUS machines. Safest workaround seems to be to continue do an early scan for all machines, but this Compal model. http://bugzilla.kernel.org/show_bug.cgi?id=14086 Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
| | * | | ACPI: EC: Rewrite DMI checksAlexey Starikovskiy2009-10-031-6/+31
| | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use dmi_check_system() for DMI matching. Don't use string "Notebook" for matching MSI hardware. http://bugzilla.kernel.org/show_bug.cgi?id=14081 Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
OpenPOWER on IntegriCloud