summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* Linux 2.6.28-rc2v2.6.28-rc2Linus Torvalds2008-10-261-1/+1
| | | | .. fix all the worst problems in -rc1
* m68k: Disable Amiga serial console support if modularGeert Uytterhoeven2008-10-261-2/+4
| | | | | | | | | | | | | | | | | | If CONFIG_AMIGA_BUILTIN_SERIAL=m, I get the following warnings: | drivers/char/amiserial.c: At top level: | drivers/char/amiserial.c:2138: warning: data definition has no type or storage class | drivers/char/amiserial.c:2138: warning: type defaults to 'int' in declaration of 'console_initcall' | drivers/char/amiserial.c:2138: warning: parameter names (without types) in function declaration | drivers/char/amiserial.c:2134: warning: 'amiserial_console_init' defined but not used because console_initcall() is not defined (nor really sensible) in the modular case. So disable serial console support if the driver is modular. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* epoll: avoid double-inserts in case of EFAULTDavide Libenzi2008-10-261-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | In commit f337b9c58332bdecde965b436e47ea4c94d30da0 ("epoll: drop unnecessary test") Thomas found that there is an unnecessary (always true) test in ep_send_events(). The callback never inserts into ->rdllink while the send loop is performed, and also does the ~EP_PRIVATE_BITS test. Given we're holding the mutex during this time, the conditions tested inside the loop are always true. HOWEVER. The test "!ep_is_linked(&epi->rdllink)" wasn't there because we insert into ->rdllink, but because the send-events loop might terminate before the whole list is scanned (-EFAULT). In such cases, when the loop terminates early, and when a (leftover) file received an event while we're performing the lockless loop, we need such test to avoid to double insert the epoll items. The list_splice() done a few steps below, will correctly re-insert the ones that were left on "txlist". This should fix the kenrel.org bugzilla entry 11831. Signed-off-by: Davide Libenzi <davidel@xmailserver.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* select: deal with math overflow from borderline valid userland dataArjan van de Ven2008-10-262-4/+6
| | | | | | | | | | | | | | | | | | | | Some userland apps seem to pass in a "0" for the seconds, and several seconds worth of usecs to select(). The old kernels accepted this just fine, so the new kernels must too. However, due to the upscaling of the microseconds to nanoseconds we had some cases where we got math overflow, and depending on the GCC version (due to inlining decisions) that actually resulted in an -EINVAL return. This patch fixes this by adding the excess microseconds to the seconds field. Also with thanks to Marcin Slusarz for spotting some implementation bugs in the diagnostics patches. Reported-by: Carlos R. Mafra <crmafra2@gmail.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* wireless: fix regression caused by regulatory config optionArjan van de Ven2008-10-261-6/+5
| | | | | | | | | | | | | | | | | | | The default for the regulatory compatibility option is wrong; if you picked the default you ended up with a non-functional wifi system (at least I did on Fedora 9 with iwl4965). I don't think even the October 2008 releases of the various distros has the new userland so clearly the default is wrong, and also we can't just go about deleting this in 2.6.29... Change the default to "y" and also adjust the config text a little to reflect this. This patch fixes regression #11859 With thanks to Johannes Berg for the diagnostics Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* cgroup: remove unused variableStephen Rothwell2008-10-261-1/+1
| | | | | | | | | | | /scratch/sfr/next/kernel/cgroup.c: In function 'cgroup_tasks_start': /scratch/sfr/next/kernel/cgroup.c:2107: warning: unused variable 'i' Introduced in commit cc31edceee04a7b87f2be48f9489ebb72d264844 "cgroups: convert tasks file to use a seq_file with shared pid array". Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6Linus Torvalds2008-10-266-45/+73
|\ | | | | | | | | | | | | | | | | | | | | * 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX hwmon: (abituguru3) Cosmetic whitespace fixes hwmon: (adt7473) Fix voltage conversion routines hwmon: (lm90) Add support for the LM99 16 degree offset hwmon: (lm90) Fix handling of hysteresis value hwmon-vid: Add support for AMD family 10h CPUs hwmon: (w83781d) Fix linking when built-in
| * hwmon: (abituguru3) enable DMI probing feature on AW9D-MAXAlistair John Strachan2008-10-261-1/+1
| | | | | | | | | | | | | | | | | | | | Switch the AW9D-MAX over from port probing to the preferred DMI probe method. Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
| * hwmon: (abituguru3) Cosmetic whitespace fixesAlistair John Strachan2008-10-261-14/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As the probable result of zealous copy/pasting, many supported boards contain sensor names with trailing whitespace. Though this is not a huge problem, it is inconsistent with other sensor names, and with other similar hwmon drivers. Additionally, the DMI nag message added in 2.6.27 was missing a space between two sentence fragments -- might as well clean that up too. Doesn't alter any kernel text, just data. Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
| * hwmon: (adt7473) Fix voltage conversion routinesJean Delvare2008-10-261-20/+9
| | | | | | | | | | | | | | | | | | | | | | | | Fix voltage conversion routines. Based on an earlier patch from Paulius Zaleckas. According to the datasheet voltage is scaled with resistors and value 192 is nominal voltage. 0 is 0V. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Cc: Darrick J. Wong <djwong@us.ibm.com>
| * hwmon: (lm90) Add support for the LM99 16 degree offsetJean Delvare2008-10-262-5/+34
| | | | | | | | | | | | | | | | | | | | The LM99 differs from the LM86, LM89 and LM90 in that it reports remote temperatures (temp2) 16 degrees lower than they really are. So far we have been cheating and handled this in userspace but it really should be handled by the driver directly. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org>
| * hwmon: (lm90) Fix handling of hysteresis valueJean Delvare2008-10-261-3/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are several problems in the way the hysteresis value is handled by the lm90 driver: * In show_temphyst(), specific handling of the MAX6646 is missing, so the hysteresis is reported incorrectly if the critical temperature is over 127 degrees C. * In set_temphyst(), the new hysteresis register value is written to the chip but data->temp_hyst isn't updated accordingly, so there is a short period of time (up to 2 seconds) where the old hystereris value will be returned while the new one is already active. * In set_temphyst(), the critical temperature which is used as a base to compute the value of the hysteresis register lacks device-specific handling. As a result, the value of the hysteresis register might be incorrect for the ADT7461 and MAX6646 chips. Fix these 3 bugs. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Nate Case <ncase@xes-inc.com>
| * hwmon-vid: Add support for AMD family 10h CPUsJean Delvare2008-10-261-0/+1
| | | | | | | | | | | | | | | | The AMD family 10h CPUs use the same VID decoding table as the family 0Fh CPUs. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Rudolf Marek <r.marek@assembler.cz>
| * hwmon: (w83781d) Fix linking when built-inGeert Uytterhoeven2008-10-261-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When w83781d is built-in, the final links fails with the following vague error message: `.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o w83781d_isa_unregister() cannot be marked __exit, as it's also called from sensors_w83781d_init(), which is marked __init. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
* | r8169: revert "read MAC address from EEPROM on init"Francois Romieu2008-10-261-88/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 7bf6bf4803df1adc927f585168d2135fb019c698. The code has both a short existence and an increasing track of failures despite some work to amend it for -rc1. It is not just a matter of reading the eeprom: sometimes the eeprom is read correctly, then the mac address is not written correctly back into the mac registers. Some chipsets seem to work reliably but it is not clear at this point if the code can simply be made to work on a per-chipset basis and post -rc1 is not the place where I want to experiment these things. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | arm ide breakageAl Viro2008-10-262-4/+4
| | | | | | | | | | | | | | | | | | | | a) semicolon before the function body is a bad idea b) it's const struct foo, not struct const foo c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver() d) compiling is occasionally useful. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | fix allmodconfig breakageAl Viro2008-10-261-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If you use KCONFIG_ALLCONFIG (even with empty file) you get broken allmodconfig/allyesconfig; CONFIG_MODULES gets turned off, with obvious massive fallout. Breakage had been introduced when conf_set_all_new_symbols() got used for allmodconfig et.al. What happens is that sym_calc_value(modules_sym) done in conf_read_simple() sets SYMBOL_VALID on both modules_sym and MODULES. When we get to conf_set_all_new_symbols(), we set sym->def[S_DEF_USER] on everything, but it has no effect on sym->curr for the symbols that already have SYMBOL_VALID - these are stuck. Solution: use sym_clear_all_valid() in there. Note that it makes reevaluation of modules_sym redundant - sym_clear_all_valid() will do that itself. [ Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11512, says Alexey ] Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | Merge branch 'for_linus' of ↵Linus Torvalds2008-10-252-24/+16
|\ \ | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4 * 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: Fix duplicate entries returned from getdents() system call ext3: Fix duplicate entries returned from getdents() system call
| * | ext4: Fix duplicate entries returned from getdents() system callTheodore Ts'o2008-10-251-12/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix a regression caused by commit d0156417, "ext4: fix ext4_dx_readdir hash collision handling", where deleting files in a large directory (requiring more than one getdents system call), results in some filenames being returned twice. This was caused by a failure to update info->curr_hash and info->curr_minor_hash, so that if the directory had gotten modified since the last getdents() system call (as would be the case if the user is running "rm -r" or "git clean"), a directory entry would get returned twice to the userspace. Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> This patch fixes the bug reported by Markus Trippelsdorf at: http://bugzilla.kernel.org/show_bug.cgi?id=11844 Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
| * | ext3: Fix duplicate entries returned from getdents() system callTheodore Ts'o2008-10-251-12/+8
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix a regression caused by commit 6a897cf4, "ext3: fix ext3_dx_readdir hash collision handling", where deleting files in a large directory (requiring more than one getdents system call), results in some filenames being returned twice. This was caused by a failure to update info->curr_hash and info->curr_minor_hash, so that if the directory had gotten modified since the last getdents() system call (as would be the case if the user is running "rm -r" or "git clean"), a directory entry would get returned twice to the userspace. This patch fixes the bug reported by Markus Trippelsdorf at: http://bugzilla.kernel.org/show_bug.cgi?id=11844 Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
* | Revert "Call init_workqueues before pre smp initcalls."Linus Torvalds2008-10-252-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit a802dd0eb5fc97a50cf1abb1f788a8f6cc5db635 by moving the call to init_workqueues() back where it belongs - after SMP has been initialized. It also moves stop_machine_init() - which needs workqueues - to a later phase using a core_initcall() instead of early_initcall(). That should satisfy all ordering requirements, and was apparently the reason why init_workqueues() was moved to be too early. Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | libata: fix bug with non-ncq devicesJens Axboe2008-10-241-1/+5
|/ | | | | | | | | | | | | | | | | | The recent commit 2fca5ccf97d2c28bcfce44f5b07d85e74e3cd18e ("libata: switch to using block layer tagging support") to enable support for block layer tagging in libata was broken for non-NCQ devices The block layer initializes the tag field to -1 to detect invalid uses of a tag, and if the libata devices does NOT support NCQ, we just used that field to index the internal command list. So we need to check for -1 first and only use the tag field if it's valid. Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Reported-by: Alexander Beregalov <a.beregalov@gmail.com> Tested-by: Paul Mundt <lethal@linux-sh.org> Tested-by: Dave Young <hidave.darkstar@gmail.com> Tested-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Linux 2.6.28-rc1v2.6.28-rc1Linus Torvalds2008-10-231-3/+3
|
* Fix PCI hotplug printk formatRandy Dunlap2008-10-231-1/+1
| | | | | | | | | Fix printk format warning: drivers/pci/hotplug/acpiphp_ibm.c:207: warning: format '%08lx' expects type 'long unsigned int', but argument 3 has type 'long long unsigned int' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'for-linus' of ↵Linus Torvalds2008-10-2316-263/+376
|\ | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: PCI: remove unused resource assignment in pci_read_bridge_bases() PCI hotplug: shpchp: message refinement PCI hotplug: shpchp: replace printk with dev_printk PCI: add routines for debugging and handling lost interrupts PCI hotplug: pciehp: message refinement PCI: fix ARI code to be compatible with mixed ARI/non-ARI systems PCI hotplug: cpqphp: fix kernel NULL pointer dereference
| * PCI: remove unused resource assignment in pci_read_bridge_bases()Zhao, Yu2008-10-231-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This cleanup removes the resource assignment in pci_read_bridge_bases() since it has taken care by pci_alloc_child_bus() when allocating the bus: /* Set up default resource pointers and names.. */ for (i = 0; i < PCI_BRIDGE_RES_NUM; i++) { child->resource[i] = &bridge->resource[PCI_BRIDGE_RESOURCES+i]; child->resource[i]->name = child->name; } Signed-off-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
| * PCI hotplug: shpchp: message refinementTaku Izumi2008-10-235-98/+86
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch refines messages in shpchp module. The main changes are as follows: - remove the trailing "." - remove __func__ as much as possible - capitalize the first letter of messages - show PCI device address including its domain Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
| * PCI hotplug: shpchp: replace printk with dev_printkTaku Izumi2008-10-235-159/+224
| | | | | | | | | | | | | | This patch replaces printks within shpchp module with dev_printks. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
| * PCI: add routines for debugging and handling lost interruptsJames Bottomley2008-10-233-1/+69
| | | | | | | | | | | | | | | | | | We're getting a lot of storage drivers blamed for interrupt misrouting issues. This patch provides a standard way of reporting the problem ... and, if possible, correcting it. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
| * PCI hotplug: pciehp: message refinementTaku Izumi2008-10-235-88/+78
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch refines messages in pciehp module. The main changes are as follows: - remove the trailing "." - remove __func__ as much as possible - capitalize the first letter of messages - show PCI device address including its domain Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
| * PCI: fix ARI code to be compatible with mixed ARI/non-ARI systemsZhao, Yu2008-10-231-8/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | The original ARI support code has a compatibility problem with non-ARI devices. If a device doesn't support ARI, turning on ARI forwarding on its upper level bridge will cause undefined behavior. This fix turns on ARI forwarding only when the subordinate devices support it. Tested-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
| * PCI hotplug: cpqphp: fix kernel NULL pointer dereferenceKenji Kaneshige2008-10-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following patch fixes the regression in 2.6.27 that causes kernel NULL pointer dereference at cpqphp driver probe time. This patch should be backported to the .27 stable series. Seems to have been introduced by f46753c5e354b857b20ab8e0fe7b2579831dc369. The root cause of this problem seems that cpqphp driver calls pci_hp_register() wrongly. In current implementation, cpqphp driver passes 'ctrl->pci_dev->subordinate' as a second parameter for pci_hp_register(). But because hotplug slots and it's hotplug controller (exists as a pci funcion) are on the same bus, it should be 'ctrl->pci_dev->bus' instead. Cc: <stable@kernel.org> Tested-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds2008-10-2335-290/+556
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits) tcp: Restore ordering of TCP options for the sake of inter-operability net: Fix disjunct computation of netdev features sctp: Fix to handle SHUTDOWN in SHUTDOWN_RECEIVED state sctp: Fix to handle SHUTDOWN in SHUTDOWN-PENDING state sctp: Add check for the TSN field of the SHUTDOWN chunk sctp: Drop ICMP packet too big message with MTU larger than current PMTU p54: enable 2.4/5GHz spectrum by eeprom bits. orinoco: reduce stack usage in firmware download path ath5k: fix suspend-related oops on rmmod [netdrvr] fec_mpc52xx: Implement polling, to make netconsole work. qlge: Fix MSI/legacy single interrupt bug. smc911x: Make the driver safer on SMP smc911x: Add IRQ polarity configuration smc911x: Allow Kconfig dependency on ARM sis190: add identifier for Atheros AR8021 PHY 8139x: reduce message severity on driver overlap igb: add IGB_DCA instead of selecting INTEL_IOATDMA igb: fix tx data corruption with transition to L0s on 82575 ehea: Fix memory hotplug support netdev: DM9000: remove BLACKFIN hacking in DM9000 netdev driver ...
| * | tcp: Restore ordering of TCP options for the sake of inter-operabilityIlpo Järvinen2008-10-231-6/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is not our bug! Sadly some devices cannot cope with the change of TCP option ordering which was a result of the recent rewrite of the option code (not that there was some particular reason steming from the rewrite for the reordering) though any ordering of TCP options is perfectly legal. Thus we restore the original ordering to allow interoperability with/through such broken devices and add some warning about this trap. Since the reordering just happened without any particular reason, this change shouldn't cost us anything. There are already couple of known failure reports (within close proximity of the last release), so the problem might be more wide-spread than a single device. And other reports which may be due to the same problem though the symptoms were less obvious. Analysis of one of the case revealed (with very high probability) that sack capability cannot be negotiated as the first option (SYN never got a response). Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Reported-by: Aldo Maggi <sentiniate@tiscali.it> Tested-by: Aldo Maggi <sentiniate@tiscali.it> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: Fix disjunct computation of netdev featuresHerbert Xu2008-10-235-75/+104
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | My change commit e2a6b85247aacc52d6ba0d9b37a99b8d1a3e0d83 net: Enable TSO if supported by at least one device didn't do what was intended because the netdev_compute_features function was designed for conjunctions. So what happened was that it would simply take the TSO status of the last constituent device. This patch extends it to support both conjunctions and disjunctions under the new name of netdev_increment_features. It also adds a new function netdev_fix_features which does the sanity checking that usually occurs upon registration. This ensures that the computation doesn't result in an illegal combination since this checking is absent when the change is initiated via ethtool. The two users of netdev_compute_features have been converted. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | sctp: Fix to handle SHUTDOWN in SHUTDOWN_RECEIVED stateWei Yongjun2008-10-233-1/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Once an endpoint has reached the SHUTDOWN-RECEIVED state, it MUST NOT send a SHUTDOWN in response to a ULP request. The Cumulative TSN Ack of the received SHUTDOWN chunk MUST be processed. This patch fix to process Cumulative TSN Ack of the received SHUTDOWN chunk in SHUTDOWN_RECEIVED state. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | sctp: Fix to handle SHUTDOWN in SHUTDOWN-PENDING stateWei Yongjun2008-10-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If SHUTDOWN is received in SHUTDOWN-PENDING state, enpoint should enter the SHUTDOWN-RECEIVED state and check the Cumulative TSN Ack field of the SHUTDOWN chunk (RFC 4960 Section 9.2). If the SHUTDOWN chunk can acknowledge all of the send DATA chunks, SHUTDOWN-ACK should be sent. But now endpoint just silently discarded the SHUTDOWN chunk. SHUTDOWN received in SHUTDOWN-PENDING state can happend when the last SACK is lost by network, or the SHUTDOWN chunk can acknowledge all of the received DATA chunks. The packet sequence(SACK lost) is like this: Endpoint A Endpoint B ULP (ESTABLISHED) (ESTABLISHED) <----------- DATA <--- shutdown Enter SHUTDOWN-PENDING state SACK ----lost----> SHUTDOWN(*1) ------------> <----------- SHUTDOWN-ACK (*1) silently discarded now. This patch fix to handle SHUTDOWN in SHUTDOWN-PENDING state as the same as ESTABLISHED state. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | sctp: Add check for the TSN field of the SHUTDOWN chunkWei Yongjun2008-10-231-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If SHUTDOWN chunk is received Cumulative TSN Ack beyond the max tsn currently send, SHUTDOWN chunk be accepted and the association will be broken. New data is send, but after received SACK it will be drop because TSN in SACK is less than the Cumulative TSN, data will be retrans again and again even if correct SACK is received. The packet sequence is like this: Endpoint A Endpoint B ULP (ESTABLISHED) (ESTABLISHED) <----------- DATA (TSN=x-1) <----------- DATA (TSN=x) SHUTDOWN -----------> (Now Cumulative TSN=x+1000) (TSN=x+1000) <----------- DATA (TSN=x+1) SACK -----------> drop the SACK (TSN=x+1) <----------- DATA (TSN=x+1)(retrans) This patch fix this problem by terminating the association and respond to the sender with an ABORT. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | sctp: Drop ICMP packet too big message with MTU larger than current PMTUWei Yongjun2008-10-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If ICMP packet too big message is received with MTU larger than current PMTU, SCTP will still accept this ICMP message and sync the PMTU of assoc with the wrong MTU. Endpoing A Endpoint B (ESTABLISHED) (ESTABLISHED) ICMP ---------> (packet too big, MTU too larger) sync PMTU This patch fixed the problem by drop that ICMP message. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | Merge branch 'master' of ↵David S. Miller2008-10-234-40/+60
| |\ \ | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
| | * | p54: enable 2.4/5GHz spectrum by eeprom bits.Christian Lamparter2008-10-221-18/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Badness at /home/proski/src/linux-2.6/net/mac80211/rx.c:2200 NIP: c02bc850 LR: c02ab268 CTR: 00000000 REGS: ef01fcc0 TRAP: 0700 Tainted: G W (2.6.27-wl) MSR: 00029032 <EE,ME,IR,DR> CR: 22004084 XER: 20000000 TASK = c1a58800[1778] 'p54pci' THREAD: ef01e000 [...] NIP [c02bc850] __ieee80211_rx+0x17c/0x638 LR [c02ab268] ieee80211_tasklet_handler+0x104/0x120 Call Trace: [ef01fd70] [c1a0c020] 0xc1a0c020 (unreliable) [ef01fdb0] [c02ab268] ieee80211_tasklet_handler+0x104/0x120 [...] the problem was that some older cards are mis-identified and didn't support 5GHz rates, while they have the right MAC & Synth chip. This patch changes the way how p54 decides if it should enable 11a channels or not. Reported-by: Pavel Roskin <proski@gnu.org> Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * | orinoco: reduce stack usage in firmware download pathAndrey Borzenkov2008-10-221-13/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | orinoco_dl_firmware and symbol_dl_mage allocate large local variables (1K); at least orinoco fails with panic or hung kernel if 4K stacks is enabled. Allocate large buffers dynamically at run time. Tested-By: Andrey Borzenkov <arvidjaar@mail.ru> for Agere case Signed-off-by: Andrey Borzenkov < arvidjaar@mail.ru> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * | ath5k: fix suspend-related oops on rmmodBob Copeland2008-10-222-9/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on a patch by Elias Oltmanns, we call ath5k_init in resume even if we didn't previously open the device. Besides starting up the device unnecessarily, this also causes an oops on rmmod because mac80211 will not invoke ath5k_stop and softirqs are left running after the module has been unloaded. Add a new state bit, ATH_STAT_STARTED, to indicate that we have been started up. Reported-by: Toralf Förster <toralf.foerster@gmx.de> Signed-off-by: Elias Oltmanns <eo@nebensachen.de> Signed-off-by: Bob Copeland <me@bobcopeland.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | | [netdrvr] fec_mpc52xx: Implement polling, to make netconsole work.Jon Smirl2008-10-221-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement polling for 5200FEC to make netconsole work. Tested on Phytec pcm030 and Efika. Signed-off-by: Jon Smirl <jonsmirl@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * | | qlge: Fix MSI/legacy single interrupt bug.Ron Mercer2008-10-222-47/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The chip can issue spurious interrupts for single interrupt modes. We use disable to clear the condition and allow processing to continue. Also got rid of legacy specific code since it now needs to be done on MSI single irq also. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * | | smc911x: Make the driver safer on SMPCatalin Marinas2008-10-221-17/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch extends the critical regions covered by lp->lock to make it safer on SMP. The main failure point was the smc911x_hard_start_xmit function being called from different CPUs. It was tested on the ARM SMP platforms. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * | | smc911x: Add IRQ polarity configurationCatalin Marinas2008-10-222-3/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Platforms like ARM Ltd's RealView require the IRQ polarity bit to be set for the SMC9118 chip. This patch allows the dynamic configuration via the smc911x_platdata structure. This patch also changes the smc91x_platdata structure name to the correct smc911x_platdata in the smc911x_drv_probe() function. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * | | smc911x: Allow Kconfig dependency on ARMCatalin Marinas2008-10-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since more ARM platforms use this device, it is easier to add a dependency on ARM rather than individual platforms. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * | | sis190: add identifier for Atheros AR8021 PHYFrancois Romieu2008-10-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes http://bugzilla.kernel.org/show_bug.cgi?id=10994 Contributed by pablomme@googlemail.com, coenraad@wish.org.za and a few others. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * | | 8139x: reduce message severity on driver overlapStephen Hemminger2008-10-222-6/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The 8139 drivers are a source of error messages that confuse users. Since this device can not be disambiguated by normal PCI device id's two drivers match the same info. But the module utilities seem to correctly handle this overlap, they try one driver, then if that doesn't load try the other. Therefore there is no need for a message to be logged with error level severity, just using info level instead. Can't be completely silent because user might have configure one driver and forgot the other one. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
OpenPOWER on IntegriCloud