| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds more generic base device trees for Vybrid SoCs. There
are three series of Vybrid SoC commonly available:
- VF3xx series: single core, Cortex-A5 without external memory
- VF5xx series: single core, Cortex-A5
- VF6xx series: dual core, Cortex-A5/Cortex-M4
The second digit represents the presents of a L2 cache (VFx1x).
The VF3xx series are not suitable for Linux especially since the
internal memory is quite small (1.5MiB).
The VF500 is essentially the base SoC, with only one core and
without L1 cache. The VF610 is a superset of the VF500, hence
vf500.dtsi is then included and enhanced by vf610.dtsi. There is
no board using VF510 or VF600 currently, but, if needed, they can
be added easily.
The Linux kernel can also run on the Cortex-M4 CPU of Vybrid
using !MMU support. This patchset creates a device tree structure
which allows to share peripherals nodes for a VF6xx Cortex-M4
device tree too. The two CPU types have different views of the
system: Foremost they are using different interrupt controllers,
but also the memory map is slightly different. The base device
tree vfxxx.dtsi allows to create SoC and board level device trees
supporting the Cortex-M4 while reusing the shared peripherals
nodes.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The clock controller module (CCM) has several clock inputs, which
are connected to external crystal oscillators. To reflect this,
assign these fixed clocks to the CCM node directly.
This especially resolves initialization order dependencies we had
with the earlier initialization code: When resolving of the fixed
clocks failed in clk-vf610, the code created fixed clocks with a
rate of 0.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
|
|
|
| |
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The LS1021A TWR is a low cost, high-performance evaluation,
development and test platform supporting the LS1021A processor.
It is optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
For more detail information about the LS1021A TWR board, please
refer to LS1021A QorIQ Tower System Reference Manual.
Signed-off-by: Chao Fu <B44548@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The LS1021A QorIQ development system (QDS) is a high-performance
computing evaluation, development and test platform supporting
the LS1021A processor. The LS1021A QDS is optimized to support
the high-bandwidth DDR3LP/DDR4 memory and a full complement of
high-speed SerDes ports.
For more detail information about the LS1021AQDS, please refer to
the QorIQ LS1021A Development System Reference Manual.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Chao Fu <B44548@freescale.com>
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This add Freescale QorIQ LS1021A SoC device tree support.
The QorIQ LS1021A processor incorporates dual ARM Cortex-A7 cores,
providing virtualization support, advanced security features and the
broadest array of high-speed interconnects and optimized peripheral
features.
The LS1021A SoC shares IPs with i.MX, Vybrid and PowerPC platform.
For the detail information about Freescale QorIQ LS1021A SoC,
please refer to the QorIQ LS1021A Reference Manual.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
|
|
|
|
|
|
| |
On registration I2C bus drivers attemp to get ids from device tree
aliases, add a missing alias for I2C4 found on iMX6 DualLite/Solo.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
|
|
|
|
|
|
|
|
| |
TBS2910 is a i.MX6Q based board. For additional details refer to
http://www.tbsdtv.com/products/tbs2910-matrix-arm-mini-pc.html
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
| |
TBS Technologies is a company which specializes in developing, producing
and marketing of digital TV tuner cards for PCs.
for additional details refer to http://www.tbsdtv.com/about-us.html
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
|
|
|
|
|
|
| |
Add enet2 support for imx6sx-sdb board, and add the "fsl,imx6q-fec"
compatible for fec2 node to be compatible with the old version.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
|
|
|
|
|
| |
Add all required properties for the cpufreq-dt driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
|
|
|
|
|
| |
Enable ADC support for Colibri VF61 modules
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
|
|
|
|
| |
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
| |
The Colibri standard defines four pins as PWM outputs, two of them (PWM
A and C) are routed to FTM instance 0 and the other two (PWM B and D)
are routed to FTM instance 1. Hence enable both FTM instances for the
Colibri module and mux the four pins accordingly.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
|
|
|
| |
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
| |
Add Global Timer support which is part of the private peripherals
of the Cortex-A5 processor. This Global Timer is compatible with the
Cortex-A9 implementation. It's a 64-bit timer and is clocked by the
peripheral clock, which is typically 133 or 166MHz on Vybrid.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
|
|
|
|
|
|
|
|
| |
SSI block has 'ipg' clock for internal peripheral access and also 'baud' clock
for generating bit clock when SSI operates in master mode.
Add the extra 'baud' clock so that we can have SSI functional in master mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
|
|
|
|
|
|
|
|
| |
SSI block has 'ipg' clock for internal peripheral access and also 'baud' clock
for generating bit clock when SSI operates in master mode.
Add the extra 'baud' clock so that we can have SSI functional in master mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The i.MX SoC update for 3.19:
- Update i.MX6 suspend code to check DDR instead of CPU type, as the
difference we need to handle is between LPDDR2 and DDR3, not SoCs.
- Set anatop properly for LPDDR2 in DSM mode
- Add support for new SoC LS1021A which integrates dual Cortex-A7
- Add ENET initialization for i.MX6SX platform
- Add cpufreq support for i.MX53 platform
- Add a SNVS based poweroff driver for i.MX6 platforms
- Use ARM Global Timer as clocksource on VF610
Note: the change set is built on top of tag imx-fixes-3.18-2 to resolve
a conflict on file arch/arm/mach-imx/clk-vf610.c.
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This driver register pm_power_off with snvs power off function. If
your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
other pin to do, please disable the driver in dts, otherwise, your
pm_power_off maybe overwrote by this driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The newly introduced LS1021A SoC selects CONFIG_SOC_FSL, which
is originally symbol used for the PowerPC based platforms
and guards lots of code that does not build on ARM.
This breaks allmodconfig, so let's remove it for now, until
either all those drivers are fixed or they use a dependency
on IMX instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
With the clock assignment device tree changes, the clocks get
initialized properly but the search for those clocks fails with
errors:
[ 0.000000] i.MX clk 4: register failed with -17
[ 0.000000] i.MX clk 5: register failed with -17
This is because the module can't find those clocks anymore, and
tries to initialize fixed clocks with the same name.
Get the clock modules input clocks from the assigned clocks by
default by using of_clk_get_by_name(). If this function returns
not a valid clock, fall back to the old behaviour and search the
input clock from the device tree's /clocks/$name node.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Freescale LS1021A SoCs deploy two cortex-A7 processors,
this adds bring-up support for the secondary core.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
| |
| |
| |
| |
| |
| |
| |
| | |
The LS1021A SoC is a dual-core Cortex-A7 based processor,
this adds the initial support for it.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
| |
| |
| |
| |
| |
| |
| | |
Instanciate device for the generic cpufreq-dt driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The ARM clock is a virtual clock feeding the ARM partition of
the SoC. It controls multiple other clocks to ensure the right
sequencing when cpufreq changes the CPU clock rate.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This implements a virtual clock used to abstract away
all the steps needed in order to change the ARM clock,
so we don't have to push all this clock handling into
the cpufreq driver.
While it will be used for i.MX53 at first it is generic
enough to be used on i.MX6 later on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This is the bypass clock used to feed the ARM partition
while we reprogram PLL1 to another rate.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add enet init for i.mx6sx:
- Add phy ar8031 fixup
- Set enet clock source from internal PLL
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add imx6sx iomux-gpr register field define in "imx6q-iomuxc-gpr.h" header
file, which is not fully define all iomux-gpr registers and fields, only
align with freescale internal tree related GPR macro define.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add the ARM Global Timer as clocksource/scheduler clock option and
use it as default scheduler clock. This leaves the PIT timer for
other users e.g. the secondary Cortex-M4 core. Also, the Global Timer
has double the precission (running at pheripheral clock compared to
IPG clock) and a 64-bit incrementing counter register. We still keep
the PIT timer as an secondary option in case the ARM Global Timer is
not available.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
For LPDDR2 platform, no need to enable weak2P5 in DSM mode,
it can be pulled down to save power(~0.65mW).
And per design team's recommendation, we should disconnect
VDDHIGH and SNVS in DSM mode on i.MX6SL.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
As the DDR/IO and MMDC setting are different on LPDDR2 and DDR3,
we used cpu type to decide how to do these settings in suspend
before which is NOT flexible, take i.MX6SL for example, although
it has LPDDR2 on EVK board, but users can also use DDR3 on other
boards, so it is better to read the DDR type from MMDC then decide
how to do related settings.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
| |\
|/ /
| |
| |
| |
| |
| |
| |
| | |
The i.MX fixes for 3.18, 2nd round:
- Fix a regression on Vybrid platform which is caused by commit
dc4805c2e78b (ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3
driver), and results in a missing configuration on PLL clocks.
- Fix a regression with i.MX defconfig files where CONFIG_SPI option
gets lost accidentally.
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Since 64546e9fe3a5b8c ("ARM: imx_v6_v7_defconfig updates") and commit
0650f855d2e4b0b9 ("ARM: imx_v4_v5_defconfig: Select CONFIG_IMX_WEIM") CONFIG_SPI
selection was dropped by savedefconfig for imx_v4_v5_defconfig and
imx_v6_v7_defconfig.
In order to keep the same behaviour as previous kernel versions and avoid
regressions, let's add CONFIG_SPI option back.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
So far, the required PLL's (PLL1/PLL2/PLL5) have been initialized
by boot loader and the kernel code defined fixed rates according
to those default configurations. Beginning with the USB PLL7 the
code started to initialize the PLL's itself (using imx_clk_pllv3).
However, since commit dc4805c2e78ba5a22ea1632f3e3e4ee601a1743b
(ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver)
imx_clk_pllv3 no longer takes care of the ENABLE and BYPASS bits,
hence the USB PLL were not configured correctly anymore.
This patch not only fixes those USB PLL's, but also makes use of
the imx_clk_pllv3 for all PLL's and alignes the code with the PLL
support of the i.MX6 series.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
| |
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull MTD fixes from Brian Norris:
"Three main MTD fixes for 3.18:
- A regression from 3.16 which was noticed in 3.17. With the
restructuring of the m25p80.c driver and the SPI NOR library
framework, we omitted proper listing of the SPI device IDs. This
means m25p80.c wouldn't auto-load (modprobe) properly when built as
a module. For now, we duplicate the device IDs into both modules.
- The OMAP / ELM modules were depending on an implicit link ordering.
Use deferred probing so that the new link order (in 3.18-rc) can
still allow for successful probing.
- Fix suspend/resume support for LH28F640BF NOR flash"
* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
mtd: omap: fix mtd devices not showing up
mtd: m25p80,spi-nor: Fix module aliases for m25p80
mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
mtd: m25p80: get rid of spi_get_device_id
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
After '#echo mem > /sys/power/state' some devices can not be properly resumed
because apparently the MTD Partition Configuration Register has been reset
to default thus the rootfs cannot be mounted cleanly on resume.
An example of this can be found in the SA-1100 Developer's Manual at 9.5.3.3
where the second step of the Sleep Shutdown Sequence is described:
"An internal reset is applied to the SA-1100. All units are reset...".
As workaround we refresh the PCR value as done initially on chip setup.
This behavior and the fix are confirmed by our tests done on 2 different Zaurus
collie units with kernel 3.17.
Fixes: 812c5fa82bae: ("mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR")
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Since commit 6d178ef2fd5e ("mtd: nand: Move ELM driver and rename as
omap_elm"), I don't have any mtd devices present on my am335x. This
changes the link order of the omap_elm and omap2 objects, causing them
to probe in the wrong order.
To fix this, make elm_config defer probing until the omap_elm driver is
actually loaded.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
m25p80's device ID table is now spi_nor_ids, defined in spi-nor. The
MODULE_DEVICE_TABLE() macro doesn't work with extern definitions, but
its use was also removed at the same time. Now if m25p80 is built as
a module it doesn't get the necessary aliases to be loaded
automatically.
A clean solution to this will involve defining the list of device
IDs in spi-nor.h and removing struct spi_device_id from the spi-nor
API, but this is quite a large change.
As a quick fix suitable for stable, copy the device IDs back into
m25p80.
Fixes: 03e296f613af ("mtd: m25p80: use the SPI nor framework")
Cc: <stable@vger.kernel.org> # 3.16.x: 32f1b7c8352f: mtd: move support for struct flash_platform_data into m25p80
Cc: <stable@vger.kernel.org> # 3.16.x: 90e55b3812a1: mtd: m25p80: get rid of spi_get_device_id
Cc: <stable@vger.kernel.org> # 3.16.x: 70f3ce0510af: mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Drivers currently call spi_nor_match_id() and then spi_nor_scan().
This adds a dependency on struct spi_device_id which we want to
avoid. Make spi_nor_scan() do it for them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
This simplifies the way we use spi_nor framework and will allow us to
drop spi_nor_match_id.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of six patches consisting of:
- two MAINTAINER updates
- two scsi-mq fixs for the old parallel interface (not every request
is tagged and we need to set the right flags to populate the SPI
tag message)
- a fix for a memory leak in scatterlist traversal caused by a
preallocation update in 3.17
- an ipv6 fix for cxgbi"
[ The scatterlist fix also came in separately through the block layer tree ]
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: ufs - remove self
MAINTAINERS: change hpsa and cciss maintainer
libcxgbi : support ipv6 address host_param
scsi: set REQ_QUEUE for the blk-mq case
Revert "block: all blk-mq requests are tagged"
lib/scatterlist: fix memory leak with scsi-mq
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
I have moved, I do not have the hardware access anymore.
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Change ownership of the hpsa driver from Stephen M. Cameron
(Hewlett-Packard) to Don Brace (PMC-Sierra).
Change ownership of the cciss driver from Mike Miller (Hewlett-Packard)
to Don Brace (PMC-Sierra).
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
libcxgbi was always returning an ipv4 address for ISCSI_HOST_PARAM_IPADDRESS,
return appropriate address based on address family
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
To generate the right SPI tag messages we need to properly set
QUEUE_FLAG_QUEUED in the request_queue and mirror it to the
request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This reverts commit fb3ccb5da71273e7f0d50b50bc879e50cedd60e7.
SCSI-2/SPI actually needs the tagged/untagged flag in the request to
work properly. Revert this patch and add a follow on to set it in
the right place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fix a memory leak with scsi-mq triggered by commands with large data
transfer length.
Fixes: c53c6d6a68b1 ("scatterlist: allow chaining to preallocated chunks")
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|