| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
| |
remove board_init_irq(): On all in-kernel boards it is sufficient to
initialize board interrupts in an arch_initcall by using the default
linux irq functions.
Some small irqmap.c files have been folded into board_setup files.
Run-tested on DB1200; compile-tested on all other affected boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
|
|
|
|
|
|
| |
Move the PB1200 IRQ cascade code out to the BCSR support code:
upcoming DB1300 support can use it too.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Seen on rm200_defconfig for example:
CC arch/mips/boot/compressed/decompress.o
/home/ralf/src/linux/upstream-linus/arch/mips/boot/compressed/decompress.c: In function ‘decompress_kernel’:
/home/ralf/src/linux/upstream-linus/arch/mips/boot/compressed/decompress.c:116: error: implicit declaration of function ‘decompress’
make[3]: *** [arch/mips/boot/compressed/decompress.o] Error 1
make[2]: *** [vmlinuz.ecoff] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Hibernate: Fix preallocating of memory
PM / Hibernate: Remove swsusp.c finally
PM / Hibernate: Remove trailing space in message
PM: Allow SCSI devices to suspend/resume asynchronously
PM: Allow USB devices to suspend/resume asynchronously
USB: implement non-tree resume ordering constraints for PCI host controllers
PM: Allow PCI devices to suspend/resume asynchronously
PM / Hibernate: Swap, remove useless check from swsusp_read()
PM / Hibernate: Really deprecate deprecated user ioctls
PM: Allow device drivers to use dpm_wait()
PM: Start asynchronous resume threads upfront
PM: Add facility for advanced testing of async suspend/resume
PM: Add a switch for disabling/enabling asynchronous suspend/resume
PM: Asynchronous suspend and resume of devices
PM: Add parent information to timing messages
PM: Document device power attributes in sysfs
PM / Runtime: Add sysfs switch for disabling device run-time PM
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The hibernate memory preallocation code allocates memory to push some
user space data out of physical RAM, so that the hibernation image is
not too large. It allocates more memory than necessary for creating
the image, so it has to release some pages to make room for
allocations made while suspending devices and disabling nonboot CPUs,
or the system will hang due to the lack of free pages to allocate
from. Unfortunately, the function used for freeing these pages,
free_unnecessary_pages(), contains a bug that prevents it from doing
the job on all systems without highmem.
Fix this problem, which is a regression from the 2.6.30 kernel, by
using the right condition for the termination of the loop in
free_unnecessary_pages().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Alan Jenkins <sourcejedi.lkml@googlemail.com>
Cc: stable@kernel.org
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Its contents and entry in Makefile were already removed in
8e60c6a1348e17e68ad73589a52a03876e7059be
(Shift remaining code from swsusp.c to hibernate.c)
but somehow it remained in-place (rjw: which most likely was my
mistake).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Remove a trailing space from a message in swsusp_save().
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Set power.async_suspend for all SCSI devices, targets and hosts, so
that they can be suspended and resumed in parallel with the main
suspend/resume thread and possibly with other devices they don't
depend on in a known way (i.e. devices which are not their parents or
children).
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Set power.async_suspend for USB devices, endpoints and interfaces,
allowing them to be suspended and resumed asynchronously during
system sleep transitions.
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch (as1331) adds non-tree ordering constraints needed for
proper resume of PCI USB host controllers from hibernation. The main
issue is that non-high-speed devices must not be resumed before the
high-speed root hub, because it is the ehci_bus_resume() routine which
takes care of handing the device connection over to the companion
controller. If the device resume is attempted before the handover
then the device won't be found and it will be treated as though it had
disconnected.
The patch adds a new field to the usb_bus structure; for each
full/low-speed bus this field will contain a pointer to the companion
high-speed bus (if one exists). It is used during normal device
resume; if the hs_companion pointer isn't NULL then we wait for the
root-hub device on the hs_companion bus.
A secondary issue is that an EHCI controlller shouldn't be resumed
before any of its companions. On some machines I have observed
handovers failing if the companion controller is reinitialized after
the handover. Thus, the EHCI resume routine must wait for the
companion controllers to be resumed.
The patch also fixes a small bug in usb_hcd_pci_probe(); an error path
jumps to the wrong label, causing a memory leak.
[rjw: Fixed compilation for CONFIG_PM_SLEEP unset.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Set power.async_suspend for all PCI devices and PCIe port services,
so that they can be suspended and resumed in parallel with other
devices they don't depend on in a known way (i.e. devices which are
not their parents or children).
This only affects the "regular" suspend and resume stages, which
means in particular that the restoration of the PCI devices' standard
configuration registers during resume will still be carried out
synchronously (at the "early" resume stage).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
It will never reach here if the sws_resume_bdev is erratic.
swsusp_read() is called only from software_resume(), but after
swsusp_check() which would catch the error state.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
They were deprecated and removed from exported headers more than 2
years ago. Inform users about their removal in the future now.
(Switch cases needed to be reorderded for an easy fall through.)
And add an entry to feature-removal-schedule.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
There are some dependencies between devices (in particular, between
EHCI USB controllers and their OHCI/UHCI siblings) which are not
reflected by the structure of the device tree. With synchronous
suspend and resume these dependencies are taken into accout
automatically, because the devices in question are always registered
in the right order, but to meet these constraints with asynchronous
suspend and resume the drivers of these devices will need to use
dpm_wait() in their suspend/resume routines, so introduce a helper
function allowing them to do that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
It has been shown by testing that total device resume time can be
reduced significantly (by as much as 50% or more) if the async
threads executing some devices' resume routines are all started
before the main resume thread starts to handle the "synchronous"
devices.
This is a consequence of the fact that the slowest devices tend to be
located at the end of dpm_list, so their resume routines are started
very late. Consequently, they have to wait for all the preceding
"synchronous" devices before their resume routines can be started
by the main resume thread, even if they are "asynchronous". By
starting their async threads upfront we effectively move those
devices towards the beginning of dpm_list, without breaking their
ordering with respect to their parents and children. As a result,
their resume routines are started much earlier and we are able to
save much more device resume time this way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add configuration switch CONFIG_PM_ADVANCED_DEBUG for compiling in
extra PM debugging/testing code allowing one to access some
PM-related attributes of devices from the user space via sysfs.
If CONFIG_PM_ADVANCED_DEBUG is set, add sysfs attribute power/async
for every device allowing the user space to access the device's
power.async_suspend flag and modify it, if desired.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| | |
Add sysfs attribute /sys/power/pm_async allowing the user space to
disable/enable asynchronous suspend/resume of devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Theoretically, the total time of system sleep transitions (suspend
to RAM, hibernation) can be reduced by running suspend and resume
callbacks of device drivers in parallel with each other. However,
there are dependencies between devices such that we're not allowed
to suspend the parent of a device before suspending the device
itself. Analogously, we're not allowed to resume a device before
resuming its parent.
The most straightforward way to take these dependencies into accout
is to start the async threads used for suspending and resuming
devices at the core level, so that async_schedule() is called for
each suspend and resume callback supposed to be executed
asynchronously.
For this purpose, introduce a new device flag, power.async_suspend,
used to mark the devices whose suspend and resume callbacks are to be
executed asynchronously (ie. in parallel with the main suspend/resume
thread and possibly in parallel with each other) and helper function
device_enable_async_suspend() allowing one to set power.async_suspend
for given device (power.async_suspend is unset by default for all
devices). For each device with the power.async_suspend flag set the
PM core will use async_schedule() to execute its suspend and resume
callbacks.
The async threads started for different devices as a result of
calling async_schedule() are synchronized with each other and with
the main suspend/resume thread with the help of completions, in the
following way:
(1) There is a completion, power.completion, for each device object.
(2) Each device's completion is reset before calling async_schedule()
for the device or, in the case of devices with the
power.async_suspend flags unset, before executing the device's
suspend and resume callbacks.
(3) During suspend, right before running the bus type, device type
and device class suspend callbacks for the device, the PM core
waits for the completions of all the device's children to be
completed.
(4) During resume, right before running the bus type, device type and
device class resume callbacks for the device, the PM core waits
for the completion of the device's parent to be completed.
(5) The PM core completes power.completion for each device right
after the bus type, device type and device class suspend (or
resume) callbacks executed for the device have returned.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| | |
Add parent information to the messages printed by the suspend/resume
core when initcall_debug is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| | |
There are sysfs attributes in /sys/devices/.../power/ that haven't
been documented yet in Documentation/ABI/. Document them as
appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add new device sysfs attribute, power/control, allowing the user
space to block the run-time power management of the devices. If this
attribute is set to "on", the driver of the device won't be able to power
manage it at run time (without breaking the rules) and the device will
always be in the full power state (except when the entire system goes
into a sleep state).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
There's currently an open Ubuntu bug[0], with the intent to compile NFS_FSCACHE
(and possibly AFS_FSCACHE, 9P_FSCACHE) into the standard Ubuntu kernel.
However, since *_FSCACHE still depends on EXPERIMENTAL, this won't happen.
As Arjan van de Ven pointed out[1], the EXPERIMENTAL flag doesn't mean that
much any more, I propose the following patch to fs/nfs/Kconfig. I'd do the
same for fs/9p/Kconfig and fs/afs/Kconfig, but as I did not test 9p or AFS, I
feel it would not be appropriate for me to remove the flag.
[0] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/440522/comments/5
[1] http://lkml.org/lkml/2010/1/23/145
Signed-off-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
toshiba_acpi: Add full hotkey support
hp-wmi: Add support for tablet rotation key
dell-laptop: Add another Dell laptop to the DMI whitelist
classmate-laptop: use a single MODULE_DEVICE_TABLE to get correct aliases
dell-laptop: Pay attention to which devices the hardware switch controls
dell-laptop: Use buffer with 32-bit physical address
dell-laptop: Blacklist machines not supporting dell-laptop
dell-laptop: Block software state changes when rfkill hard blocked
dell-laptop: Fix small memory leak
dell-laptop: Fix platform device unregistration
dell-laptop: Update rfkill state on kill switch
compal-laptop: Replace sysfs support with rfkill support
compal-laptop: Add support for known Compal made Dell laptops
MAINTAINERS: update drivers/platform/x86 information
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Calling the ENAB method on Toshiba laptops results in notifications being
sent when laptop hotkeys are pressed. This patch simply calls that method
and sets up an input device if it's successful.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The HP touchsmart tablet has a key for rotating the UI from landscape to
portrait. Add support for it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The Latitude C640 has another variation of dell in its DMI vendor entry.
Add it to the whitelist in order to enjoy the sweet fruits of software
backlight toggling.
Signed-off-by: Erik Andren <erik.andren@gmail.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Instead of a MODULE_DEVICE_TABLE for every acpi_driver ids table, we
create a table containing all ids to export to get a module alias for
each one.
This will fix automatic loading of the driver when one of the ACPI
devices is not present (like the accelerometer, which is not present in
some models).
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Right now, we assume that the hardware rfkill switch on Dells toggles all
radio devices. In fact, this can be configured in the BIOS and so right
now we may mark a device as hardware killed even when it isn't. Add code
to query the devices controlled by the switch, and use this when
determining the hardware kill state of a radio.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Calls to communicate with system firmware via a SMI (using dcdbas)
need to use a buffer that has a physical address of 4GB or less.
Currently the dell-laptop driver does not guarantee this, and when the
buffer address is higher than 4GB, the address is truncated to 32 bits
and the SMI handler writes to the wrong memory address.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The Mini family doesn't support smbios 17,11 although it reports it does.
Signed-off-by: Mario Limonciello <superm1@ubuntu.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The "hardware" switch is tied directly to a BIOS interface that will
connect and disconnect the hardware from the bus.
If you use the software interface to request the BIOS to make these
changes, the HW switch will be in an inconsistent state and LEDs may not
reflect the state of the HW.
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
|
| | |
| | |
| | |
| | |
| | |
| | | |
da_tokens was not being freed by dell-laptop on unload. Fix that.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
dell-laptop currently fails to clean up its platform device correctly.
Make sure that it's unregistered.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The rfkill interface on Dells only sends a notification that the switch
has been changed via the keyboard controller. Add a filter so we can
pick these notifications up and update the rfkill state appropriately.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This drops the support for manually groking the files in sysfs
to turn on and off the WLAN and BT for Compal laptops in favor
of platform rfkill support.
It has been combined into a single patch to not introduce regressions
in the process of simply adding rfkill support
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The following Dell laptops are known to have been manufacturer by Compal
and are supported by the compal-laptop platform driver
- Mini 9
- Mini 10
- Mini 12
- Mini 10v
- Inspiron 11z
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Many of the drivers/platform/x86 drivers have nothing to do with ACPI, so
it's kind of inappropriate for them to be stuck under the ACPI mailing
list. Add a new mailing list (platform-driver-x86@vger.kernel.org) and,
with Len's blessing, add myself as subsystem maintainer.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Anisse Astier <anisse@astier.eu>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Daniel Oliveira Nascimento <don@syst.com.br>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Henrique de Moraes Holschuh <ibm-acpi@hmh.eng.br>
Cc: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Cc: Karol Kozimor <sziwan@users.sourceforge.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Peter Feuerer <peter@piie.net>
Cc: Sujith Thomas <sujith.thomas@intel.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
|
|\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use bastmode in debugfs output
dlm: Send lockspace name with uevents
dlm: send reply before bast
dlm: fix ordering of bast and cast
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The bast mode that appears in the debugfs output should be
useful on both master and process nodes. lkb_highbast is
currently printed, and is only useful on the master node.
lkb_bastmode is only useful on the process node. This
patch sets lkb_bastmode on the master node as well, and
uses that value in the debugfs print.
Signed-off-by: David Teigland <teigland@redhat.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Although it is possible to get this information from the path,
its much easier to provide the lockspace as a seperate env
variable.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When the lock master processes a successful operation (request,
convert, cancel, or unlock), it will process the effects of the
change before sending the reply for the operation. The "effects"
of the operation are:
- blocking callbacks (basts) for any newly granted locks
- waiting or converting locks that can now be granted
The cast is queued on the local node when the reply from the lock
master is received. This means that a lock holder can receive a
bast for a lock mode that is doesn't yet know has been granted.
Signed-off-by: David Teigland <teigland@redhat.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When both blocking and completion callbacks are queued for lock,
the dlm would always deliver the completion callback (cast) first.
In some cases the blocking callback (bast) is queued before the
cast, though, and should be delivered first. This patch keeps
track of the order in which they were queued and delivers them
in that order.
This patch also keeps track of the granted mode in the last cast
and eliminates the following bast if the bast mode is compatible
with the preceding cast mode. This happens when a remotely mastered
lock is demoted, e.g. EX->NL, in which case the local node queues
a cast immediately after sending the demote message. In this way
a cast can be queued for a mode, e.g. NL, that makes an in-transit
bast extraneous.
Signed-off-by: David Teigland <teigland@redhat.com>
|
|\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (52 commits)
fs/xfs: Correct NULL test
xfs: optimize log flushing in xfs_fsync
xfs: only clear the suid bit once in xfs_write
xfs: kill xfs_bawrite
xfs: log changed inodes instead of writing them synchronously
xfs: remove invalid barrier optimization from xfs_fsync
xfs: kill the unused XFS_QMOPT_* flush flags V2
xfs: Use delay write promotion for dquot flushing
xfs: Sort delayed write buffers before dispatch
xfs: Don't issue buffer IO direct from AIL push V2
xfs: Use delayed write for inodes rather than async V2
xfs: Make inode reclaim states explicit
xfs: more reserved blocks fixups
xfs: turn off sign warnings
xfs: don't hold onto reserved blocks on remount,ro
xfs: quota limit statvfs available blocks
xfs: replace KM_LARGE with explicit vmalloc use
xfs: cleanup up xfs_log_force calling conventions
xfs: kill XLOG_VEC_SET_TYPE
xfs: remove duplicate buffer flags
...
|
| |\ \ \ \ |
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Test the value that was just allocated rather than the previously tested one.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
If we have a pinned inode it must have a log item attached to it.
Usually that log item will have ili_last_lsn already set, in which
case we only need to flush the log up to that LSN instead of doing a
full log force. This gives speedups of about 5% in some fsync heavy
workloads.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
file_remove_suid already calls into ->setattr to clear the suid and
sgid bits if needed, no need to start a second transaction to do it
ourselves.
Note that xfs_write_clear_setuid issues a sync transaction while the
path through ->setattr doesn't, but that is consistant with the
other filesystems.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
There are no more users of this function left in the XFS code
now that we've switched everything to delayed write flushing.
Remove it.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When an inode has already be flushed delayed write,
xfs_inode_clean() returns true and hence xfs_fs_write_inode() can
return on a synchronous inode write without having written the
inode. Currently these sycnhronous writes only come sync(1),
unmount, a sycnhronous NFS export and cachefiles so should be
relatively rare and out of common performance paths.
Realistically, a synchronous inode write is not necessary here; we
can avoid writing the inode by logging any non-transactional changes
that are pending. This needs to be done with synchronous
transactions, but it avoids seeking between the log and inode
clusters as we do now. We don't force the log if the inode is
pinned, though, so this differs from the fsync case. For normal
sys_sync and unmount behaviour this is fine because we do a
synchronous log force in xfs_sync_data which is called from the
->sync_fs code.
It does however break the NFS synchronous export guarantees for now,
but work is under way to fix this at a higher level or for the
higher level to provide an additional flag in the writeback control
to tell us that a log force is needed.
Portions of this patch are based on work from Dave Chinner.
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
|