summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* MIPS: OCTEON: Set proper UART clock in internal device trees.David Daney2013-07-011-1/+8
| | | | | | | | | | | | | | | | Following patch to use generic 8250 drivers will need proper clock information. So when using the internal device tree, populate the "clock-frequency" property with the correct value. Signed-off-by: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Cc: Jamie Iles <jamie@jamieiles.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.cz> Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/5515/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: BCM63XX: add support for the Netgear CVG834GFlorian Fainelli2013-07-011-0/+35
| | | | | | | | | | | | | Add support for the Netgear CVG834G and enable the two UARTs, Ethernet on the first MAC, PCI and the two leds. Signed-off-by: Florian Fainelli <florian@openwrt.org> Cc: linux-mips@linux-mips.org Cc: cernekee@gmail.com Cc: jogo@openwrt.org Cc: Florian Fainelli <florian@openwrt.org> Patchwork: https://patchwork.linux-mips.org/patch/5502/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: BCM63XX: let board specify an external GPIO to reset PHYFlorian Fainelli2013-07-012-0/+10
| | | | | | | | | | | | | | Some boards may need to reset their external PHY or switch they are attached to, add a hook for doing this along with providing custom linux/gpio.h flags for doing this. Signed-off-by: Florian Fainelli <florian@openwrt.org> Cc: linux-mips@linux-mips.org Cc: cernekee@gmail.com Cc: jogo@openwrt.org Cc: Florian Fainelli <florian@openwrt.org> Patchwork: https://patchwork.linux-mips.org/patch/5501/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: BCM63XX: provide a MAC address for BCM3368 chipsFlorian Fainelli2013-07-011-0/+10
| | | | | | | | | | | | | | The BCM3368 SoC uses a NVRAM format which is not compatible with the one used by CFE, provide a default MAC address which is suitable for use and which is the default one also being used by the bootloader on these chips. Signed-off-by: Florian Fainelli <florian@openwrt.org> Cc: linux-mips@linux-mips.org Cc: cernekee@gmail.com Cc: jogo@openwrt.org Patchwork: https://patchwork.linux-mips.org/patch/5498/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: BCM63XX: recognize Cable Modem firmware formatFlorian Fainelli2013-07-013-2/+37
| | | | | | | | | | | | | | | Add the firmware header format which is used by Broadcom Cable Modem SoCs such as the BCM3368 SoC. We export the bcm_hcs firmware format structure because it is used by user-land tools to create firmware images for these SoCs and will later be used by a corresponding MTD parser. Signed-off-by: Florian Fainelli <florian@openwrt.org> Cc: linux-mips@linux-mips.org Cc: cernekee@gmail.com Cc: jogo@openwrt.org Patchwork: https://patchwork.linux-mips.org/patch/5496/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: BCM63XX: add support for BCM3368 Cable ModemFlorian Fainelli2013-07-0115-19/+259
| | | | | | | | | | | | | | | | | | | | | | | | | | The Broadcom BCM3368 Cable Modem SoC is extremely similar to the existing BCM63xx DSL SoCs, in particular BCM6358, therefore little effort in the existing code base is required to get it supported. This patch adds support for the following on-chip peripherals: - two UARTS - GPIO - Ethernet - SPI - PCI - NOR Flash The most noticeable difference with 3368 is that it has its peripheral register at 0xfff8_0000 we check that separately in ioremap.h. Since 3368 is identical to 6358 for its clock and reset bits, we use them verbatim. Signed-off-by: Florian Fainelli <florian@openwrt.org> Cc: linux-mips@linux-mips.org Cc: cernekee@gmail.com Cc: jogo@openwrt.org Patchwork: https://patchwork.linux-mips.org/patch/5499/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: BCM63XX: select BOOT_RAWFlorian Fainelli2013-07-011-0/+1
| | | | | | | | | | | | | | Enabling BOOT_RAW is mandatory to get a binary image (objcopy from ELF to binary) to work. This does not affect the ELF kernels which are used by CFE on BCM63XX DSL platforms, but is going to be necessary to support BCM63XX on Cable Modem chips such as BCM3368. Signed-off-by: Florian Fainelli <florian@openwrt.org> Cc: linux-mips@linux-mips.org Cc: cernekee@gmail.com Cc: jogo@openwrt.org Patchwork: https://patchwork.linux-mips.org/patch/5500/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Delete Wind River ppmc eval board support.Paul Gortmaker2013-07-0115-681/+0
| | | | | | | | | | | | | | This board has been EOL for many years now; lets not burden people doing build coverage and other tree wide work with working on essentially dead files. [ralf@linux-mips.org: Also remove arch/mips/include/asm/mach-wrppmc/war.h.] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: linux-mips@linux-mips.org Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Patchwork: http://patchwork.linux-mips.org/patch/5503/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: fcntl.h: Use __kernel_off_t, not off_t.Ralf Baechle2013-07-011-2/+2
| | | | Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Use proper include guard symbol for <uapi/asm/fcntl.h>.Ralf Baechle2013-07-011-3/+3
| | | | Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: remove alloc_pci_controller prototypeJonas Gorski2013-07-011-1/+0
| | | | | | | | | | | | | | Commit 610019baddcb4c4c323c12cd44ca7f73d7145d6f ("[MIPS] Remove unused function alloc_pci_controller.") removed the function, but left the prototype in the header file. Remove it as well so people don't get tempted to use it and wonder why it doesn't work. Signed-off-by: Jonas Gorski <jogo@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5473/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: BCM63XX: select BMIPS4350 and default to 2 CPUs for supported SoCsJonas Gorski2013-07-011-0/+2
| | | | | | | | | | | | | | | | All BCM63XX SoCs starting with BCM6358 have a BMIPS4350 instead of a BMIPS3300, so select it unless support for any of the older SoCs is selected. All BMIPS4350 have only two CPUs, so select the appropriate default. Signed-off-by: Jonas Gorski <jogo@openwrt.org> Cc: linux-mips@linux-mips.org Cc: John Crispin <blogic@openwrt.org> Cc: Maxime Bizon <mbizon@freebox.fr> Cc: Florian Fainelli <florian@openwrt.org> Cc: Kevin Cernekee <cernekee@gmail.com> Patchwork: https://patchwork.linux-mips.org/patch/5355/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: BCM63XX: Handle SW IRQs 0-1Kevin Cernekee2013-07-011-0/+4
| | | | | | | | | | | | | | | MIPS software IRQs 0 and 1 are used for interprocessor signaling (IPI) on BMIPS SMP. Make the board support code aware of them. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> [jogo@openwrt.org: move sw irqs behind timer irq] Signed-off-by: Jonas Gorski <jogo@openwrt.org> Cc: linux-mips@linux-mips.org Cc: John Crispin <blogic@openwrt.org> Cc: Maxime Bizon <mbizon@freebox.fr> Cc: Florian Fainelli <florian@openwrt.org> Patchwork: https://patchwork.linux-mips.org/patch/5354/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: r4k,octeon,r2300: stack protector: change canary per taskGregory Fong2013-07-014-0/+23
| | | | | | | | | | | | | | | | | | | For non-SMP, uses the new random canary value that is stored in the task struct whenever a new task is forked. Based on ARM version in df0698be14c6683606d5df2d83e3ae40f85ed0d9 and subject to the same limitations: the variable GCC expects, __stack_chk_guard, is global, so this will not work on SMP. Quoting Nicolas Pitre <nico@fluxnic.net>: "One way to overcome this GCC limitation would be to locate the __stack_chk_guard variable into a memory page of its own for each CPU, and then use TLB locking to have each CPU see its own page at the same virtual address for each of them." Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5488/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: initial stack protector supportGregory Fong2013-07-014-0/+63
| | | | | | | | | | | | | | | | Implements basic stack protector support based on ARM version in c743f38013aeff58ef6252601e397b5ba281c633 , with Kconfig option, constant canary value set at boot time, and script to check if compiler actually supports stack protector. Tested by creating a kernel module that writes past end of char[]. Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com> Cc: linux-mips@linux-mips.org Cc: Filippo Arcidiacono <filippo.arcidiacono@st.com> Cc: Carmelo Amoroso <carmelo.amoroso@st.com> Patchwork: https://patchwork.linux-mips.org/patch/5448/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Boot: Compressed: Remove -fstack-protector from CFLAGSMarkos Chandras2013-07-011-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | When building with -fstack-protector, gcc emits the __stack_chk_guard and __stack_chk_fail symbols to check for stack stability. These symbols are defined in vmlinux but the generated vmlinux.bin that is used to create the compressed vmlinuz image has no symbol table so the linker can't find these symbols during the final linking phase. As a result of which, we need either to redefine these symbols just for the compressed image or drop the -fstack-protector option when building the compressed image. This patch implements the latter of two options. Fixes the following linking problem: dbg.c:(.text+0x7c): undefined reference to `__stack_chk_guard' dbg.c:(.text+0x80): undefined reference to `__stack_chk_guard' dbg.c:(.text+0xd4): undefined reference to `__stack_chk_guard' dbg.c:(.text+0xec): undefined reference to `__stack_chk_fail' [ralf@linux-mips.org: I'm applying this before the patch that actually adds stack protector support for MIPS. This means, it will not be possible to trigger above error message with any commit from the tree but rather they are what one would hit without this commit.] Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Markos Chandras <markos.chandras@imgtec.com> Patchwork: https://patchwork.linux-mips.org/patch/5575/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* irqdomain: Remove temporary MIPS workaround codeGrant Likely2013-06-181-12/+0
| | | | | | | | | | | The MIPS interrupt controllers are all registering their own irq_domains now. Drop the MIPS specific code because it is no longer needed. Signed-off-by: Grant Likely <grant.likely@linaro.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/5458/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* mips: lasat: sysctl: Convert use of typedef ctl_table to struct ctl_tableJoe Perches2013-06-181-7/+7
| | | | | | | | | | | This typedef is unnecessary and should just be removed. Signed-off-by: Joe Perches <joe@perches.com> Cc: Jiri Kosina <trivial@kernel.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/5460/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: MSP71xx: Remove gpio driversPaul Bolle2013-06-184-409/+0
| | | | | | | | | | | | | | | | | | The PMC MSP71XX gpio drivers were added in v2.6.28, see commit 9fa32c6b02 ("MIPS: PMC MSP71XX gpio drivers"). They are only built if CONFIG_HAVE_GPIO_LIB is set. But the Kconfig symbol HAVE_GPIO_LIB was already removed in v2.6.27, see commit 7444a72eff ("gpiolib: allow user-selection"). So these drivers were never buildable. Perhaps no-one noticed because there are no in tree users of msp71xx_init_gpio() and msp71xx_init_gpio_extended(). Anyhow, these drivers can safely be removed. Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/5345/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: DEC: remove unbuildable promcon.cPaul Bolle2013-06-182-55/+0
| | | | | | | | | | | | promcon.o is built if CONFIG_PROM_CONSOLE is set. But there's no Kconfig symbol PROM_CONSOLE, so promcon.c is unbuildable. Remove it. Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Acked-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/5344/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Fixup check for invalid scratch registerJayachandran C2013-06-131-5/+5
| | | | | | | | | | | The invalid value for scratch register is -1, so update the checks of the form (scratch_reg > 0) to be (scratch_reg >= 0). This will fix the case in Netlogic XLP where the scratch_reg can be 0. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5444/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Allow platform specific scratch registersJayachandran C2013-06-132-15/+27
| | | | | | | | | | | | | | | XLR/XLP COP0 scratch is register 22, sel 0-7. Add a function c0_kscratch() which returns the scratch register for the platform, and use the return value while generating TLB handlers. Setup kscratch_mask to 0xf for XLR/XLP since the config4 register does not exist. This allows the kernel to allocate scratch registers 0-3 if needed. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5445/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: Fix plat_irq_dispatchJayachandran C2013-06-131-4/+3
| | | | | | | | | | | | | | | | | | Fix an issue in plat_irq_dispatch due to which it can call do_IRQ with a PIC irq that is not mapped. When a per-cpu interrupt and a PIC interrupt are both active, the check 'eirr & PERCPU_IRQ_MASK' will be true, but the interrupt in 'i' will be the number of the PIC interrupt. In this case, we will call do_IRQ on the PIC interrupt without mapping it with nlm_irq_to_xirq(). Fix this by using __ffs64 instead of __ilog2_u64 and using the interrupt number instead of mask to identify per-cpu interrupts. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5432/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: Remove workarounds for early SoCsJayachandran C2013-06-131-22/+1
| | | | | | | | | | The XLPs in production do not need these workarounds. Remove the code and the associated ifdef. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5430/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: Fixup memory regions for prefetchJayachandran C2013-06-131-0/+13
| | | | | | | | | | | Fix a cache error found in stress test, caused by the prefetch instruction going beyond valid memory when acessing the last page of a region. Add the pref_backup logic similar to XLR in XLP too. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5431/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: wait for all hardware threadsJayachandran C2013-06-131-7/+20
| | | | | | | | | | | | Earlier we just waited for the first thread of the CPU to come online before proceeding to wake up others. Update it to wait for all the CPUs in the core. This will be useful when the boot-up is slow, like while debugging or when running in a simulator. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5429/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: Fix sign extension in PIC writeJayachandran C2013-06-131-1/+1
| | | | | | | | | | This does not cause a problem yet, but we do not want to write 1 to reserved bits. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5424/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: use branch instead of jumpJayachandran C2013-06-132-2/+2
| | | | | | | | | | | | | | Fix an issue in the reset code. Since this code is copied to the reset vector, using 'j' for looping is not correct. Use relative branch 'b'. Update the usage of 'j' in smpboot.S to be consistent although it is not a bug there. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5427/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: move cpu_ready array to boot areaJayachandran C2013-06-138-9/+22
| | | | | | | | | | Move the nlm_cpu_ready[] array used by the cpu wakeup code to the boot area, along with rest of the boot parameter code. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5425/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: Add nlm_get_boot_data() helperJayachandran C2013-06-132-6/+11
| | | | | | | | | | This moves the calculation and casting needed to access the CPU initialization data to a function nlm_get_boot_data() Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5426/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: Initialization when !CONFIG_SMPJayachandran C2013-06-135-8/+16
| | | | | | | | | | The core initialization and reset vector setup needs to be done even when booting uniprocessor. Move this code from smp.c to setup.c Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5428/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: Split reset code out of smpboot.SJayachandran C2013-06-135-187/+253
| | | | | | | | | | | | | The reset and core initialization code should be available for uniprocessor as well. This changes is just to take out the code into a different file, without any change to the logic. The change for uniprocessor initialization code is in a later patch. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5423/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: Split XLP device tree code to dt.cJayachandran C2013-06-134-70/+105
| | | | | | | | | | Create new flle arch/mips/netlogic/xlp/dt.c and move the device tree related code there. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5422/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: Support compressed kernelJayachandran C2013-06-132-0/+16
| | | | | | | | | | | | Add SYS_SUPPORTS_ZBOOT and SYS_SUPPORTS_ZBOOT_UART16550 config options for XLR and XLP. Update boot/compressed/uart-16550.c to add UART port for XLR and XLP. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5417/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: boot: Fixes for compressed/uart-16550.cJayachandran C2013-06-131-3/+7
| | | | | | | | | | | | Fix uart-16550.c for adding XLR/XLP support, changes are: * Make register read/write use volatile pointers * Support 32 bit IO read/write * Increase timeout in waiting for UART LSR Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5416/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: COP2 save/restore codeJayachandran C2013-06-134-1/+142
| | | | | | | | | | | | | Add COP2 register state structure and functions for Netlogic XLP. The RX and TX buffers and status registers are to be saved. Since the registers are 64-bit, do the implementation in inline assembly which works on both 32-bit and 64-bit kernels. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Cc: ddaney.cavm@gmail.com Patchwork: https://patchwork.linux-mips.org/patch/5413/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: rename nlm_cop2_save/restoreJayachandran C2013-06-132-10/+10
| | | | | | | | | | | | | Rename macro nlm_cop2_enable() to nlm_cop2_enable_irqsave() and the macro nlm_cop2_restore to nlm_cop2_disable_irqrestore(). The new names will reflect the functionality better, and will make nlm_cop2_restore() available to be used later in COP2 save/restore patch. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Cc: ddaney.cavm@gmail.com Patchwork: https://patchwork.linux-mips.org/patch/5412/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: Fix nlm_read_c2_status() definitionJayachandran C2013-06-132-3/+7
| | | | | | | | | | | | | | | The sel argument os nlm_read_c2_status() was not used and the macro returned the sel 0 in all cases. Fix this by defining two macros: nlm_read_c2_status0() and nlm_read_c2_status1() to return the two status registers. Add functions to write to the status registers as well. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Cc: ddaney.cavm@gmail.com Patchwork: https://patchwork.linux-mips.org/patch/5414/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Allow kernel to use coprocessor 2Jayachandran C2013-06-131-10/+5
| | | | | | | | | | | | | Kernel threads should be able to use COP2 if the platform needs it. Do not call die_if_kernel() for a coprocessor unusable exception if the exception due to COP2 usage. Instead, the default notifier for COP2 exceptions is updated to call die_if_kernel. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Cc: ddaney.cavm@gmail.com Patchwork: https://patchwork.linux-mips.org/patch/5415/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Move cop2 save/restore to switch_to()Jayachandran C2013-06-134-39/+44
| | | | | | | | | | | | | | | Move the common code for saving and restoring platform specific COP2 registers to switch_to(). This will make supporting new platforms (like Netlogic XLP) easier. The platform specific COP2 definitions are to be specified in asm/processor.h and in asm/cop2.h. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Cc: ddaney.cavm@gmail.com Patchwork: https://patchwork.linux-mips.org/patch/5411/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Netlogic: SWIOTLB dma ops for 32-bit DMAGanesan Ramalingam2013-06-134-0/+122
| | | | | | | | | | | | | | | Add SWIOTLB config option and related files to Netlogic platform. Some XLP SoC components like the SD/MMC interface cannot do DMA beyond 32-bit physical address. The SD/MMC driver can use memory outside this range for IO, to support this we have to add bounce buffers implemented by SWIOTLB. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Cc: Ganesan Ramalingam <ganesanr@broadcom.com> Patchwork: https://patchwork.linux-mips.org/patch/5410/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Support SWIOTLB in default dma operationsJayachandran C2013-06-132-0/+15
| | | | | | | | | | | | | | Provide a default implementation of phys_to_dma and dma_to_phys in mach-generic/dma_coherence.h. If CONFIG_NEED_SG_DMA_LENGTH is defined, the dma_length field in struct scatterlist is used. Set this up in mips_dma_map_sg so that the default mips DMA ops can be used when SWIOTLB is enabled. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5409/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Kconfig: Remove extranous help keyword.Ralf Baechle2013-06-131-1/+0
| | | | Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Kconfig: Move ZONE_DMA to a more appropriate place.Ralf Baechle2013-06-131-3/+3
| | | | Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: kernel: mcount.S: Drop FRAME_POINTER codepathMarkos Chandras2013-06-111-4/+0
| | | | | | | | | | | CONFIG_FRAME_POINTER is not selectable for MIPS so this codepath was never executed. Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Acked-by: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5440/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Implement HAVE_CONTEXT_TRACKING.Ralf Baechle2013-06-108-19/+108
| | | | | | This enables support for CONFIG_NO_HZ_FULL. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Cleanup flags in syscall flags handlers.Ralf Baechle2013-06-105-4/+6
| | | | | | This will simplify further modifications. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: using strlcpy() instead of strncpy()Chen Gang2013-06-101-1/+1
| | | | | | | | | | | | | | Ensure strings are always '\0' terminated. Or in the next pr_info() shit may hit the fan. Signed-off-by: Chen Gang <gang.chen@asianux.com> Acked-by: John Crispin <blogic@openwrt.org> Cc: david.daney@cavium.com Cc: linux-mips@linux-mips.org Cc: Linux-Arch <linux-arch@vger.kernel.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Patchwork: https://patchwork.linux-mips.org/patch/5331/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Ralink: Use strlcpy() instead of strncpy().Chen Gang2013-06-101-1/+1
| | | | | | | | | | | | | | | | | 'compatible' is used by strlen() in __of_device_is_compatible(). Ensure strings are always '\0' terminated. 'of_ids is not a structure in "include/uapi/*", so no need to initialize it completly; using strlcpy() instead of strncpy() will do. Signed-off-by: Chen Gang <gang.chen@asianux.com> Acked-by: John Crispin <blogic@openwrt.org> Cc: juhosg@openwrt.org Cc: linux-mips@linux-mips.org Cc: Linux-Arch <linux-arch@vger.kernel.org> Patchwork: https://patchwork.linux-mips.org/patch/5330/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Lantiq: Use strlcpy() instead of strncpy().Chen Gang2013-06-101-1/+1
| | | | | | | | | | | | | | | | 'compatible' is used by strlen() in __of_device_is_compatible(). Ensure strings are always '\0' terminated. 'of_ids is not a structure in "include/uapi/*", so no need to initialize it completly; using strlcpy() instead of strncpy() will do. Signed-off-by: Chen Gang <gang.chen@asianux.com> Acked-by: John Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Cc: Linux-Arch <linux-arch@vger.kernel.org> Patchwork: https://patchwork.linux-mips.org/patch/5329/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
OpenPOWER on IntegriCloud