summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath9k: Fix STA disconnect issue due to received MIC failed bcast framesSenthil Balasubramanian2010-12-072-3/+9
| | | | | | | | | | | | | | AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying this status for MIC failed frames is buggy. Due to this, MIC failure events for broadcast frames are not sent to supplicant resulted in AP disconnecting the STA. Able to pass Wifi Test case 5.2.18 with this fix. Cc: Stable <stable@kernel.org> (2.6.36+) Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: fix a DMA related race condition on resetFelix Fietkau2010-12-073-19/+10
| | | | | | | | | | | | When ath_drain_all_txq fails to stop DMA, it issues a hw reset. This reset happens at a very problematic point in time, when the hardware rx path has not been stopped yet. This could lead to memory corruption, hardware hangs or other issues. To fix these issues, simply remove the reset entirely and check the tx DMA stop status to prevent problems with fast channel changes. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: fix bug in tx powerMatteo Croce2010-12-071-4/+8
| | | | | | | | | | | The ath9k driver subtracts 3 dBm to the txpower as with two radios the signal power is doubled. The resulting value is assigned in an u16 which overflows and makes the card work at full power. Cc: stable@kernel.org Signed-off-by: Matteo Croce <matteo@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Revert "ath9k: Fix STA disconnect issue due to received MIC failed bcast frames"John W. Linville2010-12-022-4/+3
| | | | | | | | | | | | | This reverts commit 916448e77f6bcaaa7f13c3de0c3851783ae2bfd0. "As far as I can tell, either of these patches breaks multiple VIF scenarios. I'm not sure exactly why, but I had to revert this to get any of my interfaces to associate." -- Ben Greear <greearb@candelatech.com> http://marc.info/?l=linux-wireless&m=129123368719339&w=2 Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: fix more bitfield related endian issuesFelix Fietkau2010-12-022-9/+16
| | | | | | | | | A few LNA control related flags were also specified as a bitfields, however for some strange reason they were written in big-endian order this time. Fix this by using flags instead. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: fix endian issues with CTLs on AR9003Felix Fietkau2010-12-024-54/+47
| | | | | | | | | | | | | Parsing data using bitfields is messy, because it makes endian handling much harder. AR9002 and earlier got it right, AR9003 got it wrong. This might lead to either using too high or too low tx power values, depending on frequency and eeprom settings. Fix it by getting rid of the CTL related bitfields entirely and use masks instead. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix bug in reading input gpio state for ar9003Vasanthakumar Thiagarajan2010-12-022-3/+6
| | | | | | | | | | The register which gives input gpio state is 0x404c for ar9003, currently 0x4048 is wrongly used. This will disable RF and make it unusable on some of AR9003. Cc:stable@kernel.org Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge branch 'master' of ↵John W. Linville2010-12-023-6/+16
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth-2.6
| * Bluetooth: Add new PID for Atheros 3011Bala Shanmugam2010-12-012-0/+7
| | | | | | | | | | | | | | | | | | | | Atheros 3011 has small sflash firmware and needs to be blacklisted in transport driver to load actual firmware in DFU driver. Signed-off-by: Bala Shanmugam <sbalashanmugam@atheros.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
| * Bluetooth: Fix log spamming in btusb due to autosuspendStefan Seyfried2010-12-011-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | If a device is autosuspended an inability to resubmit URBs is to be expected. Check the error code and only log real errors. (Now that autosuspend is default enabled for btusb, those log messages were happening all the time e.g. with a BT mouse) Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com> Signed-off-by: Oliver Neukum <oneukum@suse.de> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
| * Bluetooth: Fix not returning proper error in SCOGustavo F. Padovan2010-11-221-3/+3
| | | | | | | | | | | | Return 0 in that situation could lead to errors in the caller. Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* | ath9k: Fix STA disconnect issue due to received MIC failed bcast framesSenthil Balasubramanian2010-11-302-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying this status for MIC failed frames is buggy. Due to this, MIC failure events for broadcast frames are not sent to supplicant resulted in AP disconnecting the STA. Able to pass Wifi Test case 5.2.18 with this fix. Cc: Stable <stable@kernel.org> (2.6.36+) Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | mac80211: Fix STA disconnect due to MIC failureSenthil Balasubramanian2010-11-301-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Th commit titled "mac80211: clean up rx handling wrt. found_sta" removed found_sta variable which caused a MIC failure event to be reported twice for a single failure to supplicant resulted in STA disconnect. This should fix WPA specific countermeasures WiFi test case (5.2.17) issues with mac80211 based drivers which report MIC failure events in rx status. Cc: Stable <stable@kernel.org> (2.6.37) Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | mac80211: ignore non-bcast mcast deauth/disassoc franesChristian Lamparter2010-11-301-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes an curious issue due to insufficient rx frame filtering. Saqeb Akhter reported frequent disconnects while streaming videos over samba: <http://marc.info/?m=128600031109136> > [ 1166.512087] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7) > [ 1526.059997] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7) > [ 2125.324356] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7) > [...] The reason is that the device generates frames with slightly bogus SA/TA addresses. e.g.: [ 2314.402316] Ignore 9f:1f:31:f8:64:ff [ 2314.402321] Ignore 9f:1f:31:f8:64:ff [ 2352.453804] Ignore 0d:1f:31:f8:64:ff [ 2352.453808] Ignore 0d:1f:31:f8:64:ff ^^ the group-address flag is set! (the correct SA/TA would be: 00:1f:31:f8:64:ff) Since the AP does not know from where the frames come, it generates a DEAUTH response for the (invalid) mcast address. This mcast deauth frame then passes through all filters and tricks the stack into thinking that the AP brutally kicked us! This patch fixes the problem by simply ignoring non-broadcast, group-addressed deauth/disassoc frames. Cc: Jouni Malinen <j@w1.fi> Cc: Johannes Berg <johannes@sipsolutions.net> Reported-by: Saqeb Akhter <saqeb.akhter@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | orinoco: abort scan on interface downDavid Kilroy2010-11-303-7/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes the problem causing the following trace: ------------[ cut here ]------------ WARNING: at linux-2.6.34/net/wireless/core.c:633 wdev_cleanup_work+0xb7/0xe0 [cfg80211]() Hardware name: Latitude C840 Pid: 707, comm: cfg80211 Not tainted 2.6.34.7-0.5-desktop #1 Call Trace: [<c02065c3>] try_stack_unwind+0x173/0x190 [<c02051cf>] dump_trace+0x3f/0xe0 [<c020662b>] show_trace_log_lvl+0x4b/0x60 [<c0206658>] show_trace+0x18/0x20 [<c064e0b3>] dump_stack+0x6d/0x72 [<c02443ae>] warn_slowpath_common+0x6e/0xb0 [<c0244403>] warn_slowpath_null+0x13/0x20 [<e2db5497>] wdev_cleanup_work+0xb7/0xe0 [cfg80211] [<c025cfa9>] run_workqueue+0x79/0x170 [<c025d123>] worker_thread+0x83/0xe0 [<c025fef4>] kthread+0x74/0x80 [<c0203826>] kernel_thread_helper+0x6/0x10 ---[ end trace 3f0348b3b0c6f4ff ]--- Reported by: Giacomo Comes <comes@naic.edu> Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | carl9170: fix carl9170_tx_prepare typoChristian Lamparter2010-11-291-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | commit: "carl9170: revamp carl9170_tx_prepare" introduced a peculiar bug that would only show up if the the module parameter noht is set to 1. Then all outbound voice, video and background frames would each invoke a (bogus) RTS/CTS handshake. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | mac80211: Fix frame injection using non-AP vifJouni Malinen2010-11-291-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In order for frame injection to work properly for some use cases (e.g., finding the station entry and keys for encryption), mac80211 needs to find the correct sdata entry. This works when the main vif is in AP mode, but commit a2c1e3dad516618cb0fbfb1a62c36d0b0744573a broke this particular use case for station main vif. While this type of injection is quite unusual operation, it has some uses and we should fix it. Do this by changing the monitor vif sdata selection to allow station vif to be selected instead of limiting it to just AP vifs. We still need to skip some iftypes to avoid selecting unsuitable vif for injection. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: Disable SWBA interrupt on remove_interfaceRajkumar Manoharan2010-11-291-1/+10
| | | | | | | | | | | | | | | | | | while removing beaconing mode interface, SWBA interrupt was never disabled when there are no other beaconing interfaces. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k/carl9170: advertise P2PJohannes Berg2010-11-293-2/+6
| | | | | | | | | | | | | | | | | | | | With some upcoming changes we'd like to use the interface types for P2P capability tests. Enable them now so that when we add those tests in wpa_supplicant, nothing will break. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: use per-device struct for pm_qos_* operationsGabor Juhos2010-11-293-9/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ath9k driver uses a shared pm_qos_request_list structure for all devices. This causes the following warning if more than one device is present in the system: WARNING: at kernel/pm_qos_params.c:234 ath9k_init_device+0x5e8/0x6b0() pm_qos_add_request() called for already added request Modules linked in: Call Trace: [<802b1cdc>] dump_stack+0x8/0x34 [<8007dd90>] warn_slowpath_common+0x78/0xa4 [<8007de44>] warn_slowpath_fmt+0x2c/0x38 [<801b0828>] ath9k_init_device+0x5e8/0x6b0 [<801bc508>] ath_pci_probe+0x2dc/0x39c [<80176254>] pci_device_probe+0x64/0xa4 [<8019471c>] driver_probe_device+0xbc/0x188 [<80194854>] __driver_attach+0x6c/0xa4 [<80193e20>] bus_for_each_dev+0x60/0xb0 [<80193580>] bus_add_driver+0xcc/0x268 [<80194c08>] driver_register+0xe0/0x198 [<801764e0>] __pci_register_driver+0x50/0xe0 [<80365f48>] ath9k_init+0x3c/0x6c [<8006050c>] do_one_initcall+0xfc/0x1d8 [<80355340>] kernel_init+0xd4/0x174 [<800639a4>] kernel_thread_helper+0x10/0x18 ---[ end trace 5345fc6f870564a6 ]--- This patch fixes that warning by using a separate pm_qos_request_list sructure for each device. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | libertas: fix invalid accessSven Neumann2010-11-292-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | card->priv must not be accessed after lbs_remove_card() was called as lbs_remove_card() frees card->priv via free_netdev(). For libertas_sdio this is a regression introduced by 23b149c1890f9. The correct fix to the issue described there is simply to remove the assignment. This flag is set at the appropriate time inside lbs_remove_card anyway. Reported-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Sven Neumann <s.neumann@raumfeld.com> Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | libertas: fix memory corruption in lbs_remove_card()Daniel Drake2010-11-291-2/+0
| | | | | | | | | | | | | | | | | | | | "priv" is stored at the end of the wiphy structure, which is freed during the call to lbs_cfg_free(). It must not be touched afterwards. Remove the unnecessary NULL assignment causing this memory corruption. Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | wireless: b43: fix error path in SDIOGuennadi Liakhovetski2010-11-231-0/+1
| | | | | | | | | | | | | | | | | | Fix unbalanced call to sdio_release_host() on the error path. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | carl9170: fix virtual interface setup crashChristian Lamparter2010-11-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes a faulty bound check which caused a crash when too many virtual interface were brought up. BUG: unable to handle kernel NULL pointer dereference at 00000004 IP: [<f8125f67>] carl9170_op_add_interface+0x1d7/0x2c0 [carl9170] *pde = 00000000 Oops: 0002 [#1] PREEMPT Modules linked in: carl9170 [...] Pid: 4720, comm: wpa_supplicant Not tainted 2.6.37-rc2-wl+ EIP: 0060:[<f8125f67>] EFLAGS: 00210206 CPU: 0 EIP is at carl9170_op_add_interface+0x1d7/0x2c0 [carl9170] EAX: 00000000 ... Process wpa_supplicant Stack: f4f88f34 fffffff4 .. Call Trace: [<f8f4e666>] ? ieee80211_do_open+0x406/0x5c0 [mac80211] [...] Code: <89> 42 04 ... EIP: [<f8125f67>] carl9170_op_add_interface+0x1d7/0x2c0 [carl9170] CR2: 0000000000000004 Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ssb: b43-pci-bridge: Add new vendor for BCM4318Daniel Klaffenbach2010-11-222-0/+2
| | | | | | | | | | | | | | | | | | Add new vendor for Broadcom 4318. Signed-off-by: Daniel Klaffenbach <danielklaffenbach@gmail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: fix timeout on stopping rx dmaFelix Fietkau2010-11-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | It seems that using ath9k_hw_stoppcurecv to stop rx dma is not enough. When it's time to stop DMA, the PCU is still busy, so the rx enable bit never clears. Using ath9k_hw_abortpcurecv helps with getting rx stopped much faster, with this change, I cannot reproduce the rx stop related WARN_ON anymore. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_htc: Avoid setting QoS control for non-QoS framesRajkumar Manoharan2010-11-181-1/+1
| | | | | | | | | | | | | | | | | | Setting tid information in the TX header is required only for QoS frames. Not handling this case causes severe data loss with some APs. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | cfg80211: fix can_beacon_sec_chan, reenable HT40Mark Mentovai2010-11-181-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | This follows wireless-testing 9236d838c920e90708570d9bbd7bb82d30a38130 ("cfg80211: fix extension channel checks to initiate communication") and fixes accidental case fall-through. Without this fix, HT40 is entirely blocked. Signed-off-by: Mark Mentovai <mark@moxienet.com> Cc: stable@kernel.org Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | cfg80211: fix extension channel checks to initiate communicationLuis R. Rodriguez2010-11-161-0/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When operating in a mode that initiates communication and using HT40 we should fail if we cannot use both primary and secondary channels to initiate communication. Our current ht40 allowmap only covers STA mode of operation, for beaconing modes we need a check on the fly as the mode of operation is dynamic and there other flags other than disable which we should read to check if we can initiate communication. Do not allow for initiating communication if our secondary HT40 channel has is either disabled, has a passive scan flag, a no-ibss flag or is a radar channel. Userspace now has similar checks but this is also needed in-kernel. Reported-by: Jouni Malinen <jouni.malinen@atheros.com> Cc: stable@kernel.org Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_hw: Set proper eeprom offset for AR9287 HTC devicesRajkumar Manoharan2010-11-162-1/+5
| | | | | | | | | | | | | | | | | | AR9287 based PCI & USB devices are differed in eeprom start offset. So set proper the offset for HTC devices to read nvram correctly. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_htc: Add new devices into AR7010Rajkumar Manoharan2010-11-163-1/+9
| | | | | | | | | | | | | | | | Treat new PIDs (0xA704, 0x1200) as AR7010 devices. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_htc: Update usb device ID listRajkumar Manoharan2010-11-161-0/+5
| | | | | | | | | | | | | | | | Added new VID/PIDs into supported devices list Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: Remove pm_qos request after hw unregister.Vivek Natarajan2010-11-161-2/+1
| | | | | | | | | | | | | | | | | | | | Update pm_qos before removing it in deinit_device to prevent this warning: pm_qos_update_request() called for unknown object. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | carl9170: fix usb anchor wait timeoutChristian Lamparter2010-11-151-2/+2
| | | | | | | | | | | | | | | | usb_wait_anchor_empty_timeout's @timeout wants milliseconds and not jiffies. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | cfg80211: fix WIPHY_FLAG_IBSS_RSN bitJussi Kivilinna2010-11-151-1/+1
| | | | | | | | | | | | | | | | | | WIPHY_FLAG_IBSS_RSN is BIT(7) as is WIPHY_FLAG_CONTROL_PORT_PROTOCOL. Change to BIT(8). Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | b43legacy: Fix compile on ARM architectureArnd Hannemann2010-11-151-0/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When b43legacy is compiled on the arm platform, the following errors are seen: CC [M] drivers/net/wireless/b43legacy/xmit.o In file included from include/net/dst.h:11, from drivers/net/wireless/b43legacy/xmit.c:31: include/net/dst_ops.h:28: error: expected ':', ',', ';', '}' or '__attribute__' before '____cacheline_aligned_in_smp' include/net/dst_ops.h: In function 'dst_entries_get_fast': include/net/dst_ops.h:33: error: 'struct dst_ops' has no member named 'pcpuc_entries' include/net/dst_ops.h: In function 'dst_entries_get_slow': include/net/dst_ops.h:41: error: 'struct dst_ops' has no member named 'pcpuc_entries' include/net/dst_ops.h: In function 'dst_entries_add': include/net/dst_ops.h:49: error: 'struct dst_ops' has no member named 'pcpuc_entries' include/net/dst_ops.h: In function 'dst_entries_init': include/net/dst_ops.h:55: error: 'struct dst_ops' has no member named 'pcpuc_entries' include/net/dst_ops.h: In function 'dst_entries_destroy': include/net/dst_ops.h:60: error: 'struct dst_ops' has no member named 'pcpuc_entries' make[4]: *** [drivers/net/wireless/b43legacy/xmit.o] Error 1 make[3]: *** [drivers/net/wireless/b43legacy] Error 2 make[2]: *** [drivers/net/wireless] Error 2 make[1]: *** [drivers/net] Error 2 make: *** [drivers] Error 2 The cause is a missing include of <linux/cache.h>, which is present for i386 and x86_64 architectures, but not for arm. Signed-off-by: Arnd Hannemann <arnd@arndnet.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: dont use pci_dev before it being assignWey-Yi Guy2010-11-091-1/+2
| | | | | | | | | | In order to use build-in debugging macro, pci_dev in priv need to be assigned first. This fix iwl3945 driver oopsed at boot with 2.6.37-rc1 Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Bluetooth: Add MacBookAir3,1(2) supportEdgar (gimli) Hucek2010-11-091-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adding the new MacBookAir3,1(2) to btusb. Output without the patch and btusb loaded : T: Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=05ac ProdID=821b Rev= 0.34 S: Manufacturer=Apple Inc. S: Product=Bluetooth USB Host Controller C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Output with the patch and btusb loaded : T: Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=05ac ProdID=821b Rev= 0.34 S: Manufacturer=Apple Inc. S: Product=Bluetooth USB Host Controller C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Edgar (gimli) Hucek <gimli@dark-green.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* Bluetooth: fix not setting security level when creating a rfcomm sessionLuiz Augusto von Dentz2010-11-091-3/+10
| | | | | | | | | | | This cause 'No Bonding' to be used if userspace has not yet been paired with remote device since the l2cap socket used to create the rfcomm session does not have any security level set. Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com> Acked-by: Ville Tervo <ville.tervo@nokia.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* Bluetooth: fix endianness conversion in L2CAPGustavo F. Padovan2010-11-091-2/+2
| | | | | | | Last commit added a wrong endianness conversion. Fixing that. Reported-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* Bluetooth: fix unaligned access to l2cap conf datasteven miao2010-11-091-4/+4
| | | | | | | | | | | | In function l2cap_get_conf_opt() and l2cap_add_conf_opt() the address of opt->val sometimes is not at the edge of 2-bytes/4-bytes, so 2-bytes/4 bytes access will cause data misalignment exeception. Use get_unaligned_le16/32 and put_unaligned_le16/32 function to avoid data misalignment execption. Signed-off-by: steven miao <realmz6@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* Bluetooth: Enable USB autosuspend by default on btusbMatthew Garrett2010-11-091-0/+2
| | | | | | | | | | We've done this for a while in Fedora without any obvious problems other than some interaction with input devices. Those should be fixed now, so let's try this in mainline. Signed-off-by: Matthew Garrett <mjg@redhat.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* Bluetooth: Fix non-SSP auth request for HIGH security level socketsJohan Hedberg2010-11-091-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | When initiating dedicated bonding a L2CAP raw socket with HIGH security level is used. The kernel is supposed to trigger the authentication request in this case but this doesn't happen currently for non-SSP (pre-2.1) devices. The reason is that the authentication request happens in the remote extended features callback which never gets called for non-SSP devices. This patch fixes the issue by requesting also authentiation in the (normal) remote features callback in the case of non-SSP devices. This rule is applied only for HIGH security level which might at first seem unintuitive since on the server socket side MEDIUM is already enough for authentication. However, for the clients we really want to prefer the server side to decide the authentication requrement in most cases, and since most client sockets use MEDIUM it's better to be avoided on the kernel side for these sockets. The important socket to request it for is the dedicated bonding one and that socket uses HIGH security level. The patch is based on the initial investigation and patch proposal from Andrei Emeltchenko <endrei.emeltchenko@nokia.com>. Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* Bluetooth: fix hidp kconfig dependency warningRandy Dunlap2010-11-091-1/+1
| | | | | | | | | | Fix kconfig dependency warning to satisfy dependencies: warning: (BT_HIDP && NET && BT && BT_L2CAP && INPUT || USB_HID && HID_SUPPORT && USB && INPUT) selects HID which has unmet direct dependencies (HID_SUPPORT && INPUT) Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* ath9k_hw: Fix memory leak on ath9k_hw_rf_alloc_ext_banks failureRajkumar Manoharan2010-11-081-0/+1
| | | | | | | | | The allocated externel radio banks have to be freed in case of ath9k_hw_rf_alloc_ext_banks failure. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_htc: Fix probe failure if CONFIG_USB_DEBUG enabledRajkumar Manoharan2010-11-081-16/+14
| | | | | | | | | | | | | | | | | | | | | | | Since the endpoint descriptors (EP3 & EP4) were changed from Interrupt to Bulk type by firmware, the urb submission done on Bulk pipes. And the recent commit "check the endpoint type against the pipe type" added aditional error checking against pipe types under CONFIG_USB_DEBUG. So bmAttribute has to be updated for both EP3 & EP4 before submitting urbs on that pipe. This patch resolves the following failure. [ 2215.710936] usb 1-1: usb_probe_device [ 2215.710945] usb 1-1: configuration #1 chosen from 1 choice [ 2215.711152] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 2215.711252] ath9k_hif_usb 1-1:1.0: usb_probe_interface [ 2215.711255] ath9k_hif_usb 1-1:1.0: usb_probe_interface - got id [ 2215.712780] usb 1-1: BOGUS urb xfer, pipe 3 != type 1 [ 2215.713782] usb 1-1: ath9k_htc: Unable to allocate URBs [ 2215.713801] ath9k_hif_usb: probe of 1-1:1.0 failed with error -22 Reported-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_htc: Add support for device ID 3346Haitao Zhang2010-11-081-0/+1
| | | | | | | This patch adds support for USB dongle with device ID 3346 from IMC Networks. Signed-off-by: Haitao Zhang <minipanda@linuxrobot.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Fix AR9280 surprise removal during frequent idle on/offVasanthakumar Thiagarajan2010-11-082-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Bit 22 of AR_WA should be set to fix the situation where chip reset is asynchronous to clock of analog shift registers, such that when reset is released, it could mess up the values of analog shift registers and cause some hw issue on AR9280. This bit is write only, but the driver does a read-modify-write on AR_WA without setting bit 22 in ar9002_hw_configpcipowersave() during radio disable. This causes surprise removal of hw. It can never recover from this state and the hw will become usable only after a power on/off cycle, and sometimes only during a cold reboot. This issue can be triggered by doing frequent roaming with the simple/test-roam script available from the wifi-test project [1] when roaming between APs quickly. When roaming there is a is a high possibility that the device being put into idle (radio disable) state by mac80211 during AUTH->ASSOC. A device hardware reset would fail and the kernel would output: [40251.363799] ath: AWAKE -> FULL-SLEEP [40251.363815] ieee80211 phy17: device no longer idle - working [40251.363817] ath: Marking phy17 as not-idle [40251.363819] ath: FULL-SLEEP -> AWAKE [40251.415978] pciehp 0000:00:1c.3:pcie04: Card not present on Slot(3) [40251.419896] ath: ah->misc_mode 0x4 [40251.428138] pciehp 0000:00:1c.3:pcie04: Card present on Slot(3) [40251.532247] ath: timeout (100000 us) on reg 0x9860: 0xffffffff & 0x00000001 != 0x00000000 [40251.532250] ath: Unable to reset channel (2462 MHz), reset status -5 [40251.532422] ath: Set channel: 5745 MHz [40251.540639] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.548826] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.557023] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.565211] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.573415] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.581603] ath: Failed to stop TX DMA in 100 msec after killing last frame [40251.581606] ath: Failed to stop TX DMA. Resetting hardware! [40251.592679] ath: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff [40251.703330] ath: timeout (100000 us) on reg 0x7000: 0xffffffff & 0x00000003 != 0x00000000 [40251.703333] ath: RTC stuck in MAC reset [40251.703334] ath: Chip reset failed [40251.703335] ath: Unable to reset hardware; reset status -22 This is currently only reproducible with some HB92 (Half Mini-PCIE) cards but the fix applies to all AR9280 cards. This patch fixes this issue by setting bit 22 during radio disable. This patch has fixes for all kernels that has ath9k. [1] http://wireless.kernel.org/en/developers/Testing/wifi-test Cc: kyungwan.nam@atheros.com Cc: amod.bodas@atheros.com Cc: david.quan@atheros.com Cc: stable@kernel.org Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* libertas: terminate scan when stopping interfaceDaniel Drake2010-11-083-2/+11
| | | | | | | | | | | | | | There are currently no provisions in place to ensure that the scanning task has been stopped when the interface is stopped or removed. This can result in a WARNING at net/wireless/core.c:643 and other badness when you remove the module while a scan is happening. Terminate the scanning task during interface stop. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: unset SDATA_STATE_OFFCHANNEL when cancelling a scanBrian Cavagnolo2010-11-081-3/+3
| | | | | | | | | | | | | | | | | For client STA interfaces, ieee80211_do_stop unsets the relevant interface's SDATA_STATE_RUNNING state bit prior to cancelling an interrupted scan. When ieee80211_offchannel_return is invoked as part of cancelling the scan, it doesn't bother unsetting the SDATA_STATE_OFFCHANNEL bit because it sees that the interface is down. Normally this doesn't matter because when the client STA interface is brought back up, it will probably issue a scan. But in some cases (e.g., the user changes the interface type while it is down), the SDATA_STATE_OFFCHANNEL bit will remain set. This prevents the interface queues from being started. So we cancel the scan before unsetting the SDATA_STATE_RUNNING bit. Signed-off-by: Brian Cavagnolo <brian@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
OpenPOWER on IntegriCloud