| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
| |
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch fixes the following warning introduced in e4fc408e0e99
("packet: nlmon: virtual netlink monitoring device for packet
sockets") reported by Dan Carpenter:
warning: "drivers/net/nlmon.c:31 nlmon_is_valid_mtu()
warn: always true condition '(new_mtu <= ((~0 >> 1))) =>
(s32min-s32max <= s32max)'"
Thus, we should simply remove the test against INT_MAX. Next to that
we also need to explicitly cast the sizeof() case as the comparison
is type promoted to unsigned long so negative values are then
valid instead of invalid. While at it, this also adds a comment about
Netlink and MTUs.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
| |
Cosmetic patch to add a newline after logging the device's MACID.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
| |
This makes the error handling much more simpler than open-coding everything and
in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
| |
We may use nice macros to prefix our messages with proper device name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
| |
There is no much sense to mark functions inline that are going to be used in
the other compile modules.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
| |
I tested with the AX88179 usb dongle, if without .reset_resume hook,
after S3/S4 resume you have to enable network interface or reload the
dirver module manually otherwise the network interface can not work.
Signed-off-by: David Chang <dchang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
| |
Correct a typo in description of driver_info, it should be Gigabit
Signed-off-by: David Chang <dchang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit d2d68ba9 (ipv4: Cache input routes in fib_info nexthops)
assmued that "locally destined, and routed packets, never trigger
PMTU events or redirects that will be processed by us".
However, it seems that tunnel devices do trigger PMTU events in certain
cases. At least ip_gre, ip6_gre, sit, and ipip do use the inner flow's
skb_dst(skb)->ops->update_pmtu to propage mtu information from the
outer flows. These can cause the inner flow mtu to be decreased. If
next hop exceptions are not consulted for pmtu, IP fragmentation will
not be done properly for these routes.
It also seems that we really need to have the PMTU information always
for netfilter TCPMSS clamp-to-pmtu feature to work properly.
So for the time being, cache separate copies of input routes for
each next hop exception.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
RFC3590/RFC3810 specifies we should resend MLD reports as soon as a
valid link-local address is available.
We now use the valid_ll_addr_cnt to check if it is necessary to resend
a new report.
Changes since Flavio Leitner's version:
a) adapt for valid_ll_addr_cnt
b) resend first reports directly in the path and just arm the timer for
mc_qrv-1 resends.
Reported-by: Flavio Leitner <fleitner@redhat.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
To reduce the number of unnecessary router solicitations, MLDv2 and IGMPv3
messages we need to track the number of valid (as in non-optimistic,
no-dad-failed and non-tentative) link-local addresses. Therefore, this
patch implements a valid_ll_addr_cnt in struct inet6_dev.
We now only emit router solicitations if the first link-local address
finishes duplicate address detection.
The changes for MLDv2 and IGMPv3 are in a follow-up patch.
While there, also simplify one if statement(one minor nit I made in one
of my previous patches):
if (!...)
do();
else
return;
<<into>>
if (...)
return;
do();
Cc: Flavio Leitner <fbl@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Suggested-by: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
| |
A simple semantic change, when a slave's MAC is cloned by the bond
master then set addr_assign_type to NET_ADDR_STOLEN instead of
NET_ADDR_SET. Also use bond_set_dev_addr() in BOND_FOM_ACTIVE mode
to change the bond's MAC address because the assign_type has to be
set properly.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In struct bonding there's a member called dev_addr_from_first which is
used to denote when the bond dev should clone the first slave's MAC
address but since we have netdev's addr_assign_type variable that is not
necessary. We clone the first slave's MAC each time we have a random MAC
set to the bond device. This has the nice side-effect of also fixing an
inconsistency - when the MAC address of the bond dev is set after its
creation, but prior to having slaves, it's not kept and the first slave's
MAC is cloned. The only way to keep the MAC was to create the bond device
with the MAC address set (e.g. through ip link). In all cases if the
bond device is left without any slaves - its MAC gets reset to a random
one as before.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
| |
We have a member called setup_by_slave in struct bonding to denote if the
bond dev has different type than ARPHRD_ETHER, but that is already denoted
in bond's netdev type variable if it was setup by the slave, so use that
instead of the member.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since (c05cdb1 netlink: allow large data transfers from user-space),
netlink splats if it invokes skb_clone on large netlink skbs since:
* skb_shared_info was not correctly initialized.
* skb->destructor is not set in the cloned skb.
This was spotted by trinity:
[ 894.990671] BUG: unable to handle kernel paging request at ffffc9000047b001
[ 894.991034] IP: [<ffffffff81a212c4>] skb_clone+0x24/0xc0
[...]
[ 894.991034] Call Trace:
[ 894.991034] [<ffffffff81ad299a>] nl_fib_input+0x6a/0x240
[ 894.991034] [<ffffffff81c3b7e6>] ? _raw_read_unlock+0x26/0x40
[ 894.991034] [<ffffffff81a5f189>] netlink_unicast+0x169/0x1e0
[ 894.991034] [<ffffffff81a601e1>] netlink_sendmsg+0x251/0x3d0
Fix it by:
1) introducing a new netlink_skb_clone function that is used in nl_fib_input,
that sets our special skb->destructor in the cloned skb. Moreover, handle
the release of the large cloned skb head area in the destructor path.
2) not allowing large skbuffs in the netlink broadcast path. I cannot find
any reasonable use of the large data transfer using netlink in that path,
moreover this helps to skip extra skb_clone handling.
I found two more netlink clients that are cloning the skbs, but they are
not in the sendmsg path. Therefore, the sole client cloning that I found
seems to be the fib frontend.
Thanks to Eric Dumazet for helping to address this issue.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This patch allows to switch the netns when packet is encapsulated or
decapsulated. In other word, the encapsulated packet is received in a netns,
where the lookup is done to find the tunnel. Once the tunnel is found, the
packet is decapsulated and injecting into the corresponding interface which
stands to another netns.
When one of the two netns is removed, the tunnel is destroyed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
| |
The goal of this new function is to perform all needed cleanup before sending
an skb into another netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
| |
Add ethtool operation to read RMON registers.
Tested against net-next on i.MX28.
v2: make conditional on #ifndef CONFIG_M5272
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
When a new tokenized address gets installed we send out just one
router solicition. We should send out `rtr_solicits' in case one router
advertisment got lost.
So, rearm the timer as we do in addrconf_dad_complete.
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
| |
Since commit 32b8a8e59c9c "sit: add IPv4 over IPv4 support",
tunnel->parms.iph.protocol is 0 when both 4in4 and 6in4 are setup, but
xfrm_lookup() is called only when proto is != 0, thus we need to pass the real
value.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
Just one patch this time.
1) Drop packets when the matching SA is in larval state and add a
statistic counter for that. From Fan Du.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When host ping its peer, ICMP echo request packet triggers IPsec
policy, then host negotiates SA secret with its peer. After IKE
installed SA for OUT direction, but before SA for IN direction
installed, host get ICMP echo reply from its peer. At the time
being, the SA state for IN direction could be XFRM_STATE_ACQ,
then the received packet will be dropped after adding
LINUX_MIB_XFRMINSTATEINVALID statistic.
Adding a LINUX_MIB_XFRMACQUIREERROR statistic counter for such
scenario when SA in larval state is much clearer for user than
LINUX_MIB_XFRMINSTATEINVALID which indicates the SA is totally
bad.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
As reported by "kbuild test robot" there were some errors and warnings
on attempt to build kernel with "make ARCH=powerpc allmodconfig".
And this patch addresses both errors and warnings.
Below is a list of introduced changes:
1. Fix compile-time errors (misspellings in "dma_unmap_single") on PPC.
2. Use DMA address instead of "skb->data" as a pointer to data buffer.
This fixed warnings on pointer to int conversion on 64-bit systems.
3. Re-implemented initial allocation of Rx buffers in "arc_emac_open" in
the same way they're re-allocated during operation (receiving packets).
So once again DMA address could be used instead of "skb->data".
4. Explicitly use EMAC_BUFFER_SIZE for Rx buffers allocation.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: netdev@vger.kernel.org
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Joe Perches <joe@perches.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, we fail only when all of the ips in arp_ip_target are gone.
However, in some situations we might need to fail if even one host from
arp_ip_target becomes unavailable.
All situations, obviously, rely on the idea that we need *completely*
functional network, with all interfaces/addresses working correctly.
One real world example might be:
vlans on top on bond (hybrid port). If bond and vlans have ips assigned
and we have their peers monitored via arp_ip_target - in case of switch
misconfiguration (trunk/access port), slave driver malfunction or
tagged/untagged traffic dropped on the way - we will be able to switch
to another slave.
Though any other configuration needs that if we need to have access to all
arp_ip_targets.
This patch adds this possibility by adding a new parameter -
arp_all_targets (both as a module parameter and as a sysfs knob). It can be
set to:
0 or any (the default) - which works exactly as it's working now -
the slave is up if any of the arp_ip_targets are up.
1 or all - the slave is up if all of the arp_ip_targets are up.
This parameter can be changed on the fly (via sysfs), and requires the mode
to be active-backup and arp_validate to be enabled (it obeys the
arp_validate config on which slaves to validate).
Internally it's done through:
1) Add target_last_arp_rx[BOND_MAX_ARP_TARGETS] array to slave struct. It's
an array of jiffies, meaning that slave->target_last_arp_rx[i] is the
last time we've received arp from bond->params.arp_targets[i] on this
slave.
2) If we successfully validate an arp from bond->params.arp_targets[i] in
bond_validate_arp() - update the slave->target_last_arp_rx[i] with the
current jiffies value.
3) When getting slave's last_rx via slave_last_rx(), we return the oldest
time when we've received an arp from any address in
bond->params.arp_targets[].
If the value of arp_all_targets == 0 - we still work the same way as
before.
Also, update the documentation to reflect the new parameter.
v3->v4:
Kill the forgotten rtnl_unlock(), rephrase the documentation part to be
more clear, don't fail setting arp_all_targets if arp_validate is not set -
it has no effect anyway but can be easier to set up. Also, print a warning
if the last arp_ip_target is removed while the arp_interval is on, but not
the arp_validate.
v2->v3:
Use _bh spinlock, remove useless rtnl_lock() and use jiffies for new
arp_ip_target last arp, instead of slave_last_rx(). On bond_enslave(),
use the same initialization value for target_last_arp_rx[] as is used
for the default last_arp_rx, to avoid useless interface flaps.
Also, instead of failing to remove the last arp_ip_target just print a
warning - otherwise it might break existing scripts.
v1->v2:
Correctly handle adding/removing hosts in arp_ip_target - we need to
shift/initialize all slave's target_last_arp_rx. Also, don't fail module
loading on arp_all_targets misconfiguration, just disable it, and some
minor style fixes.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Add some details to bonding documentation on how backup slave arp
validation works.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, if we receive any arp packet on a backup slave in active-backup
mode and arp_validate enabled, we suppose that it's an arp request, swap
source/target ip and try to validate it. This optimization gives us
virtually no downtime in the most common situation (active and backup
slaves are in the same broadcast domain and the active slave failed).
However, if we can't reach the arp_ip_target(s), we end up in an endless
loop of reselecting slaves, because we receive our arp requests, sent by
the active slave, and think that backup slaves are up, thus selecting them
as active and, again, sending arp requests, which fool our backup slaves.
Fix this by not validating the swapped arp packets if the current active
slave didn't receive any arp reply after it was selected as active. This
way we will only accept arp requests if we know that the current active
slave can actually reach arp_ip_target.
v3->v4:
Obey 80 lines and make checkpatch.pl happy, per Sergei's suggestion.
v1->v3:
No change.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, we validate all the incoming arps if arp_validate not 0.
However, we don't have to validate backup slaves if arp_validate == active
and vice versa, so return early in bond_arp_rcv() in these cases.
It works correctly now because we verify arp_validate in slave_last_rx(),
however we're just doing useless work in bond_arp_rcv().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| | |
Print a warning and skip them.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add function bond_get_targets_ip(targets, ip) which searches through
targets array of ips (arp_targets) and returns the position of first
match. If ip == 0, returns the first free slot. On failure to find the
ip or free slot, return -1.
Use it to verify if the arp we've received is valid and in sysfs.
v1->v2:
Fix "[2/6] bonding: add helper function bond_get_targets_ip(targets, ip)",
per Nikolay's advice, to verify if source ip != 0.0.0.0, otherwise we might
update 'null' arp_ip_targets' last_rx. Also, address style.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
guard the davinci_mdio_of_mtable table and davinci_mdio_probe_dt()
with CONFIG_OF.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch cleans up the OF parser code, removes unnecessary checks
on of_property_read_*() and guards davinci_emac_of_match table with
CONFIG_OF.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Use devm_ioremap_resource instead of devm_request_mem_region()/devm_ioremap()
and devm_request_irq() instead of request_irq().
This ensures more consistent error values and simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| | |
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When macvtap forwards skb to its tap, it needs to check
if GSO needs to be performed. This is sometimes necessary
when the HW device performed GRO, but the guest reading
from the tap does not support it (ex: Windows 7).
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When the user issues TUNSETOFFLOAD ioctl, macvtap does not do
anything other then to verify arguments. This patch adds
functionality to allow users to actually control offload features.
NETIF_F_GSO and NETIF_F_GRO are always on, but the rest of the
features can be controlled.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently macvtap uses rcu_bh functions in its
user facing fuction macvtap_get_user() and macvtap_put_user().
However, its packet handlers use normal rcu as the rcu_read_lock()
is taken in netif_receive_skb(). We can safely discontinue
the usage or rcu with bh disabled.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Macvtap uses a private lock to protect the relationship between
macvtap_queue and macvlan_dev. The private lock is not needed
since the relationship is managed by user via open(), release(),
and dellink() calls. dellink() already happens under rtnl, so
we can safely convert open() and release(), and use it in ioctl()
as well.
Suggested by Eric Dumazet.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
select/poll busy-poll support.
Split sysctl value into two separate ones, one for read and one for poll.
updated Documentation/sysctl/net.txt
Add a new poll flag POLL_LL. When this flag is set, sock_poll will call
sk_poll_ll if possible. sock_poll sets this flag in its return value
to indicate to select/poll when a socket that can busy poll is found.
When poll/select have nothing to report, call the low-level
sock_poll again until we are out of time or we find something.
Once the system call finds something, it stops setting POLL_LL, so it can
return the result to the user ASAP.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Driver for non-standard on-chip ethernet device ARC EMAC 10/100,
instantiated in some legacy ARC (Synopsys) FPGA Boards such as
ARCAngel4/ML50x.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Joe Perches <joe@perches.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
No need to have an extra ret variable when we directly can return
the value of sctp_get_port_local().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Rather instead of having the endpoint clean the garbage from the
socket, use a sk_destruct handler sctp_destruct_sock(), that does
the job for that when there are no more references on the socket.
At least do this for our crypto transform through crypto_free_hash()
that is allocated when in listening state.
Also, perform sctp_put_port() only when sk is valid. At a later
point in time we can still determine if there's an option of
placing this into sk_prot->unhash() or sctp_endpoint_free() without
any races. For now, leave it in sctp_endpoint_destroy() though.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
A trailing newline has been forgotten to add into the WARN().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, SCTP code defines its own timeval functions (since timeval
is rarely used inside the kernel by others), namely tv_lt() and
TIMEVAL_ADD() macros, that operate on SCTP cookie expiration.
We might as well remove all those, and operate directly on ktime
structures for a couple of reasons: ktime is available on all archs;
complexity of ktime calculations depending on the arch is less than
(reduces to a simple arithmetic operations on archs with
BITS_PER_LONG == 64 or CONFIG_KTIME_SCALAR) or equal to timeval
functions (other archs); code becomes more readable; macros can be
thrown out.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
Add two ktime helper functions that i) convert a given msec value to
a ktime structure and ii) that adds a msec value to a ktime structure.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We do neither ship a test_frame.h, nor will this be compatible with
the 2.5 out-of-tree lksctp kernel test suite anyway. So remove this
artefact.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
Should not allow negative num_vfs
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
Warning prints when there are command timeout to help debugging future
failures.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
It is not safe to use sscanf.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.com>
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
Since this variable is now part of a structure and not allocated dynamically,
this test is irrelevant now.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
Print a warning when a TX timeout is detected
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
