diff options
Diffstat (limited to 'sound/soc/pxa')
-rw-r--r-- | sound/soc/pxa/Kconfig | 3 | ||||
-rw-r--r-- | sound/soc/pxa/corgi.c | 35 | ||||
-rw-r--r-- | sound/soc/pxa/poodle.c | 1 | ||||
-rw-r--r-- | sound/soc/pxa/pxa2xx-ac97.c | 282 | ||||
-rw-r--r-- | sound/soc/pxa/pxa2xx-i2s.c | 63 | ||||
-rw-r--r-- | sound/soc/pxa/pxa2xx-pcm.c | 265 | ||||
-rw-r--r-- | sound/soc/pxa/pxa2xx-pcm.h | 15 | ||||
-rw-r--r-- | sound/soc/pxa/spitz.c | 47 |
8 files changed, 116 insertions, 595 deletions
diff --git a/sound/soc/pxa/Kconfig b/sound/soc/pxa/Kconfig index 9212c37..f8c1cdd 100644 --- a/sound/soc/pxa/Kconfig +++ b/sound/soc/pxa/Kconfig @@ -1,6 +1,7 @@ config SND_PXA2XX_SOC tristate "SoC Audio for the Intel PXA2xx chip" depends on ARCH_PXA + select SND_PXA2XX_LIB help Say Y or M if you want to add support for codecs attached to the PXA2xx AC97, I2S or SSP interface. You will also need @@ -13,6 +14,8 @@ config SND_PXA2XX_AC97 config SND_PXA2XX_SOC_AC97 tristate select AC97_BUS + select SND_ARM + select SND_PXA2XX_LIB_AC97 select SND_SOC_AC97_BUS config SND_PXA2XX_SOC_I2S diff --git a/sound/soc/pxa/corgi.c b/sound/soc/pxa/corgi.c index 0a53f72..1a8373d 100644 --- a/sound/soc/pxa/corgi.c +++ b/sound/soc/pxa/corgi.c @@ -18,13 +18,13 @@ #include <linux/timer.h> #include <linux/interrupt.h> #include <linux/platform_device.h> +#include <linux/gpio.h> #include <sound/core.h> #include <sound/pcm.h> #include <sound/soc.h> #include <sound/soc-dapm.h> #include <asm/mach-types.h> -#include <asm/hardware/scoop.h> #include <mach/pxa-regs.h> #include <mach/hardware.h> #include <mach/corgi.h> @@ -54,8 +54,8 @@ static void corgi_ext_control(struct snd_soc_codec *codec) switch (corgi_jack_func) { case CORGI_HP: /* set = unmute headphone */ - set_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MUTE_L); - set_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MUTE_R); + gpio_set_value(CORGI_GPIO_MUTE_L, 1); + gpio_set_value(CORGI_GPIO_MUTE_R, 1); snd_soc_dapm_disable_pin(codec, "Mic Jack"); snd_soc_dapm_disable_pin(codec, "Line Jack"); snd_soc_dapm_enable_pin(codec, "Headphone Jack"); @@ -63,24 +63,24 @@ static void corgi_ext_control(struct snd_soc_codec *codec) break; case CORGI_MIC: /* reset = mute headphone */ - reset_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MUTE_L); - reset_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MUTE_R); + gpio_set_value(CORGI_GPIO_MUTE_L, 0); + gpio_set_value(CORGI_GPIO_MUTE_R, 0); snd_soc_dapm_enable_pin(codec, "Mic Jack"); snd_soc_dapm_disable_pin(codec, "Line Jack"); snd_soc_dapm_disable_pin(codec, "Headphone Jack"); snd_soc_dapm_disable_pin(codec, "Headset Jack"); break; case CORGI_LINE: - reset_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MUTE_L); - reset_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MUTE_R); + gpio_set_value(CORGI_GPIO_MUTE_L, 0); + gpio_set_value(CORGI_GPIO_MUTE_R, 0); snd_soc_dapm_disable_pin(codec, "Mic Jack"); snd_soc_dapm_enable_pin(codec, "Line Jack"); snd_soc_dapm_disable_pin(codec, "Headphone Jack"); snd_soc_dapm_disable_pin(codec, "Headset Jack"); break; case CORGI_HEADSET: - reset_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MUTE_L); - set_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MUTE_R); + gpio_set_value(CORGI_GPIO_MUTE_L, 0); + gpio_set_value(CORGI_GPIO_MUTE_R, 1); snd_soc_dapm_enable_pin(codec, "Mic Jack"); snd_soc_dapm_disable_pin(codec, "Line Jack"); snd_soc_dapm_disable_pin(codec, "Headphone Jack"); @@ -114,8 +114,8 @@ static int corgi_shutdown(struct snd_pcm_substream *substream) struct snd_soc_codec *codec = rtd->socdev->codec; /* set = unmute headphone */ - set_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MUTE_L); - set_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MUTE_R); + gpio_set_value(CORGI_GPIO_MUTE_L, 1); + gpio_set_value(CORGI_GPIO_MUTE_R, 1); return 0; } @@ -218,22 +218,14 @@ static int corgi_set_spk(struct snd_kcontrol *kcontrol, static int corgi_amp_event(struct snd_soc_dapm_widget *w, struct snd_kcontrol *k, int event) { - if (SND_SOC_DAPM_EVENT_ON(event)) - set_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_APM_ON); - else - reset_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_APM_ON); - + gpio_set_value(CORGI_GPIO_APM_ON, SND_SOC_DAPM_EVENT_ON(event)); return 0; } static int corgi_mic_event(struct snd_soc_dapm_widget *w, struct snd_kcontrol *k, int event) { - if (SND_SOC_DAPM_EVENT_ON(event)) - set_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MIC_BIAS); - else - reset_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_MIC_BIAS); - + gpio_set_value(CORGI_GPIO_MIC_BIAS, SND_SOC_DAPM_EVENT_ON(event)); return 0; } @@ -330,6 +322,7 @@ static struct snd_soc_machine snd_soc_machine_corgi = { /* corgi audio private data */ static struct wm8731_setup_data corgi_wm8731_setup = { + .i2c_bus = 0, .i2c_address = 0x1b, }; diff --git a/sound/soc/pxa/poodle.c b/sound/soc/pxa/poodle.c index a4697f7..f84f7d8 100644 --- a/sound/soc/pxa/poodle.c +++ b/sound/soc/pxa/poodle.c @@ -284,6 +284,7 @@ static struct snd_soc_machine snd_soc_machine_poodle = { /* poodle audio private data */ static struct wm8731_setup_data poodle_wm8731_setup = { + .i2c_bus = 0, .i2c_address = 0x1b, }; diff --git a/sound/soc/pxa/pxa2xx-ac97.c b/sound/soc/pxa/pxa2xx-ac97.c index d94a495..a7a3a9c 100644 --- a/sound/soc/pxa/pxa2xx-ac97.c +++ b/sound/soc/pxa/pxa2xx-ac97.c @@ -13,225 +13,30 @@ #include <linux/init.h> #include <linux/module.h> #include <linux/platform_device.h> -#include <linux/interrupt.h> -#include <linux/wait.h> -#include <linux/clk.h> -#include <linux/delay.h> #include <sound/core.h> -#include <sound/pcm.h> #include <sound/ac97_codec.h> -#include <sound/initval.h> #include <sound/soc.h> +#include <sound/pxa2xx-lib.h> -#include <asm/irq.h> -#include <linux/mutex.h> #include <mach/hardware.h> #include <mach/pxa-regs.h> -#include <mach/pxa2xx-gpio.h> -#include <mach/audio.h> #include "pxa2xx-pcm.h" #include "pxa2xx-ac97.h" -static DEFINE_MUTEX(car_mutex); -static DECLARE_WAIT_QUEUE_HEAD(gsr_wq); -static volatile long gsr_bits; -static struct clk *ac97_clk; -#ifdef CONFIG_PXA27x -static struct clk *ac97conf_clk; -#endif - -/* - * Beware PXA27x bugs: - * - * o Slot 12 read from modem space will hang controller. - * o CDONE, SDONE interrupt fails after any slot 12 IO. - * - * We therefore have an hybrid approach for waiting on SDONE (interrupt or - * 1 jiffy timeout if interrupt never comes). - */ - -static unsigned short pxa2xx_ac97_read(struct snd_ac97 *ac97, - unsigned short reg) -{ - unsigned short val = -1; - volatile u32 *reg_addr; - - mutex_lock(&car_mutex); - - /* set up primary or secondary codec/modem space */ -#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) - reg_addr = ac97->num ? &SAC_REG_BASE : &PAC_REG_BASE; -#else - if (reg == AC97_GPIO_STATUS) - reg_addr = ac97->num ? &SMC_REG_BASE : &PMC_REG_BASE; - else - reg_addr = ac97->num ? &SAC_REG_BASE : &PAC_REG_BASE; -#endif - reg_addr += (reg >> 1); - -#ifndef CONFIG_PXA27x - if (reg == AC97_GPIO_STATUS) { - /* read from controller cache */ - val = *reg_addr; - goto out; - } -#endif - - /* start read access across the ac97 link */ - GSR = GSR_CDONE | GSR_SDONE; - gsr_bits = 0; - val = *reg_addr; - - wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_SDONE, 1); - if (!((GSR | gsr_bits) & GSR_SDONE)) { - printk(KERN_ERR "%s: read error (ac97_reg=%x GSR=%#lx)\n", - __func__, reg, GSR | gsr_bits); - val = -1; - goto out; - } - - /* valid data now */ - GSR = GSR_CDONE | GSR_SDONE; - gsr_bits = 0; - val = *reg_addr; - /* but we've just started another cycle... */ - wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_SDONE, 1); - -out: mutex_unlock(&car_mutex); - return val; -} - -static void pxa2xx_ac97_write(struct snd_ac97 *ac97, unsigned short reg, - unsigned short val) -{ - volatile u32 *reg_addr; - - mutex_lock(&car_mutex); - - /* set up primary or secondary codec/modem space */ -#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) - reg_addr = ac97->num ? &SAC_REG_BASE : &PAC_REG_BASE; -#else - if (reg == AC97_GPIO_STATUS) - reg_addr = ac97->num ? &SMC_REG_BASE : &PMC_REG_BASE; - else - reg_addr = ac97->num ? &SAC_REG_BASE : &PAC_REG_BASE; -#endif - reg_addr += (reg >> 1); - - GSR = GSR_CDONE | GSR_SDONE; - gsr_bits = 0; - *reg_addr = val; - wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_CDONE, 1); - if (!((GSR | gsr_bits) & GSR_CDONE)) - printk(KERN_ERR "%s: write error (ac97_reg=%x GSR=%#lx)\n", - __func__, reg, GSR | gsr_bits); - - mutex_unlock(&car_mutex); -} - static void pxa2xx_ac97_warm_reset(struct snd_ac97 *ac97) { -#ifdef CONFIG_PXA3xx - int timeout = 100; -#endif - gsr_bits = 0; - -#ifdef CONFIG_PXA27x - /* warm reset broken on Bulverde, - so manually keep AC97 reset high */ - pxa_gpio_mode(113 | GPIO_OUT | GPIO_DFLT_HIGH); - udelay(10); - GCR |= GCR_WARM_RST; - pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT); - udelay(500); -#elif defined(CONFIG_PXA3xx) - /* Can't use interrupts */ - GCR |= GCR_WARM_RST; - while (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR)) && timeout--) - mdelay(1); -#else - GCR |= GCR_WARM_RST | GCR_PRIRDY_IEN | GCR_SECRDY_IEN; - wait_event_timeout(gsr_wq, gsr_bits & (GSR_PCR | GSR_SCR), 1); -#endif - - if (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR))) - printk(KERN_INFO "%s: warm reset timeout (GSR=%#lx)\n", - __func__, gsr_bits); + pxa2xx_ac97_try_warm_reset(ac97); - GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN); - GCR |= GCR_SDONE_IE|GCR_CDONE_IE; + pxa2xx_ac97_finish_reset(ac97); } static void pxa2xx_ac97_cold_reset(struct snd_ac97 *ac97) { -#ifdef CONFIG_PXA3xx - int timeout = 1000; - - /* Hold CLKBPB for 100us */ - GCR = 0; - GCR = GCR_CLKBPB; - udelay(100); - GCR = 0; -#endif + pxa2xx_ac97_try_cold_reset(ac97); - GCR &= GCR_COLD_RST; /* clear everything but nCRST */ - GCR &= ~GCR_COLD_RST; /* then assert nCRST */ - - gsr_bits = 0; -#ifdef CONFIG_PXA27x - /* PXA27x Developers Manual section 13.5.2.2.1 */ - clk_enable(ac97conf_clk); - udelay(5); - clk_disable(ac97conf_clk); - GCR = GCR_COLD_RST; - udelay(50); -#elif defined(CONFIG_PXA3xx) - /* Can't use interrupts on PXA3xx */ - GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN); - - GCR = GCR_WARM_RST | GCR_COLD_RST; - while (!(GSR & (GSR_PCR | GSR_SCR)) && timeout--) - mdelay(10); -#else - GCR = GCR_COLD_RST; - GCR |= GCR_CDONE_IE|GCR_SDONE_IE; - wait_event_timeout(gsr_wq, gsr_bits & (GSR_PCR | GSR_SCR), 1); -#endif - - if (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR))) - printk(KERN_INFO "%s: cold reset timeout (GSR=%#lx)\n", - __func__, gsr_bits); - - GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN); - GCR |= GCR_SDONE_IE|GCR_CDONE_IE; -} - -static irqreturn_t pxa2xx_ac97_irq(int irq, void *dev_id) -{ - long status; - - status = GSR; - if (status) { - GSR = status; - gsr_bits |= status; - wake_up(&gsr_wq); - -#ifdef CONFIG_PXA27x - /* Although we don't use those we still need to clear them - since they tend to spuriously trigger when MMC is used - (hardware bug? go figure)... */ - MISR = MISR_EOC; - PISR = PISR_EOC; - MCSR = MCSR_EOC; -#endif - - return IRQ_HANDLED; - } - - return IRQ_NONE; + pxa2xx_ac97_finish_reset(ac97); } struct snd_ac97_bus_ops soc_ac97_ops = { @@ -244,7 +49,7 @@ struct snd_ac97_bus_ops soc_ac97_ops = { static struct pxa2xx_pcm_dma_params pxa2xx_ac97_pcm_stereo_out = { .name = "AC97 PCM Stereo out", .dev_addr = __PREG(PCDR), - .drcmr = &DRCMRTXPCDR, + .drcmr = &DRCMR(12), .dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG | DCMD_BURST32 | DCMD_WIDTH4, }; @@ -252,7 +57,7 @@ static struct pxa2xx_pcm_dma_params pxa2xx_ac97_pcm_stereo_out = { static struct pxa2xx_pcm_dma_params pxa2xx_ac97_pcm_stereo_in = { .name = "AC97 PCM Stereo in", .dev_addr = __PREG(PCDR), - .drcmr = &DRCMRRXPCDR, + .drcmr = &DRCMR(11), .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC | DCMD_BURST32 | DCMD_WIDTH4, }; @@ -260,7 +65,7 @@ static struct pxa2xx_pcm_dma_params pxa2xx_ac97_pcm_stereo_in = { static struct pxa2xx_pcm_dma_params pxa2xx_ac97_pcm_aux_mono_out = { .name = "AC97 Aux PCM (Slot 5) Mono out", .dev_addr = __PREG(MODR), - .drcmr = &DRCMRTXMODR, + .drcmr = &DRCMR(10), .dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG | DCMD_BURST16 | DCMD_WIDTH2, }; @@ -268,7 +73,7 @@ static struct pxa2xx_pcm_dma_params pxa2xx_ac97_pcm_aux_mono_out = { static struct pxa2xx_pcm_dma_params pxa2xx_ac97_pcm_aux_mono_in = { .name = "AC97 Aux PCM (Slot 5) Mono in", .dev_addr = __PREG(MODR), - .drcmr = &DRCMRRXMODR, + .drcmr = &DRCMR(9), .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC | DCMD_BURST16 | DCMD_WIDTH2, }; @@ -276,7 +81,7 @@ static struct pxa2xx_pcm_dma_params pxa2xx_ac97_pcm_aux_mono_in = { static struct pxa2xx_pcm_dma_params pxa2xx_ac97_pcm_mic_mono_in = { .name = "AC97 Mic PCM (Slot 6) Mono in", .dev_addr = __PREG(MCDR), - .drcmr = &DRCMRRXMCDR, + .drcmr = &DRCMR(8), .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC | DCMD_BURST16 | DCMD_WIDTH2, }; @@ -285,24 +90,13 @@ static struct pxa2xx_pcm_dma_params pxa2xx_ac97_pcm_mic_mono_in = { static int pxa2xx_ac97_suspend(struct platform_device *pdev, struct snd_soc_dai *dai) { - GCR |= GCR_ACLINK_OFF; - clk_disable(ac97_clk); - return 0; + return pxa2xx_ac97_hw_suspend(); } static int pxa2xx_ac97_resume(struct platform_device *pdev, struct snd_soc_dai *dai) { - pxa_gpio_mode(GPIO31_SYNC_AC97_MD); - pxa_gpio_mode(GPIO30_SDATA_OUT_AC97_MD); - pxa_gpio_mode(GPIO28_BITCLK_AC97_MD); - pxa_gpio_mode(GPIO29_SDATA_IN_AC97_MD); -#ifdef CONFIG_PXA27x - /* Use GPIO 113 as AC97 Reset on Bulverde */ - pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT); -#endif - clk_enable(ac97_clk); - return 0; + return pxa2xx_ac97_hw_resume(); } #else @@ -313,61 +107,13 @@ static int pxa2xx_ac97_resume(struct platform_device *pdev, static int pxa2xx_ac97_probe(struct platform_device *pdev, struct snd_soc_dai *dai) { - int ret; - - ret = request_irq(IRQ_AC97, pxa2xx_ac97_irq, IRQF_DISABLED, "AC97", NULL); - if (ret < 0) - goto err; - - pxa_gpio_mode(GPIO31_SYNC_AC97_MD); - pxa_gpio_mode(GPIO30_SDATA_OUT_AC97_MD); - pxa_gpio_mode(GPIO28_BITCLK_AC97_MD); - pxa_gpio_mode(GPIO29_SDATA_IN_AC97_MD); -#ifdef CONFIG_PXA27x - /* Use GPIO 113 as AC97 Reset on Bulverde */ - pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT); - - ac97conf_clk = clk_get(&pdev->dev, "AC97CONFCLK"); - if (IS_ERR(ac97conf_clk)) { - ret = PTR_ERR(ac97conf_clk); - ac97conf_clk = NULL; - goto err_irq; - } -#endif - ac97_clk = clk_get(&pdev->dev, "AC97CLK"); - if (IS_ERR(ac97_clk)) { - ret = PTR_ERR(ac97_clk); - ac97_clk = NULL; - goto err_irq; - } - clk_enable(ac97_clk); - return 0; - - err_irq: - GCR |= GCR_ACLINK_OFF; -#ifdef CONFIG_PXA27x - if (ac97conf_clk) { - clk_put(ac97conf_clk); - ac97conf_clk = NULL; - } -#endif - free_irq(IRQ_AC97, NULL); - err: - return ret; + return pxa2xx_ac97_hw_probe(pdev); } static void pxa2xx_ac97_remove(struct platform_device *pdev, struct snd_soc_dai *dai) { - GCR |= GCR_ACLINK_OFF; - free_irq(IRQ_AC97, NULL); -#ifdef CONFIG_PXA27x - clk_put(ac97conf_clk); - ac97conf_clk = NULL; -#endif - clk_disable(ac97_clk); - clk_put(ac97_clk); - ac97_clk = NULL; + pxa2xx_ac97_hw_remove(pdev); } static int pxa2xx_ac97_hw_params(struct snd_pcm_substream *substream, diff --git a/sound/soc/pxa/pxa2xx-i2s.c b/sound/soc/pxa/pxa2xx-i2s.c index c796b18..2fb5829 100644 --- a/sound/soc/pxa/pxa2xx-i2s.c +++ b/sound/soc/pxa/pxa2xx-i2s.c @@ -21,6 +21,7 @@ #include <sound/pcm.h> #include <sound/initval.h> #include <sound/soc.h> +#include <sound/pxa2xx-lib.h> #include <mach/hardware.h> #include <mach/pxa-regs.h> @@ -30,6 +31,54 @@ #include "pxa2xx-pcm.h" #include "pxa2xx-i2s.h" +struct pxa2xx_gpio { + u32 sys; + u32 rx; + u32 tx; + u32 clk; + u32 frm; +}; + +/* + * I2S Controller Register and Bit Definitions + */ +#define SACR0 __REG(0x40400000) /* Global Control Register */ +#define SACR1 __REG(0x40400004) /* Serial Audio I 2 S/MSB-Justified Control Register */ +#define SASR0 __REG(0x4040000C) /* Serial Audio I 2 S/MSB-Justified Interface and FIFO Status Register */ +#define SAIMR __REG(0x40400014) /* Serial Audio Interrupt Mask Register */ +#define SAICR __REG(0x40400018) /* Serial Audio Interrupt Clear Register */ +#define SADIV __REG(0x40400060) /* Audio Clock Divider Register. */ +#define SADR __REG(0x40400080) /* Serial Audio Data Register (TX and RX FIFO access Register). */ + +#define SACR0_RFTH(x) ((x) << 12) /* Rx FIFO Interrupt or DMA Trigger Threshold */ +#define SACR0_TFTH(x) ((x) << 8) /* Tx FIFO Interrupt or DMA Trigger Threshold */ +#define SACR0_STRF (1 << 5) /* FIFO Select for EFWR Special Function */ +#define SACR0_EFWR (1 << 4) /* Enable EFWR Function */ +#define SACR0_RST (1 << 3) /* FIFO, i2s Register Reset */ +#define SACR0_BCKD (1 << 2) /* Bit Clock Direction */ +#define SACR0_ENB (1 << 0) /* Enable I2S Link */ +#define SACR1_ENLBF (1 << 5) /* Enable Loopback */ +#define SACR1_DRPL (1 << 4) /* Disable Replaying Function */ +#define SACR1_DREC (1 << 3) /* Disable Recording Function */ +#define SACR1_AMSL (1 << 0) /* Specify Alternate Mode */ + +#define SASR0_I2SOFF (1 << 7) /* Controller Status */ +#define SASR0_ROR (1 << 6) /* Rx FIFO Overrun */ +#define SASR0_TUR (1 << 5) /* Tx FIFO Underrun */ +#define SASR0_RFS (1 << 4) /* Rx FIFO Service Request */ +#define SASR0_TFS (1 << 3) /* Tx FIFO Service Request */ +#define SASR0_BSY (1 << 2) /* I2S Busy */ +#define SASR0_RNE (1 << 1) /* Rx FIFO Not Empty */ +#define SASR0_TNF (1 << 0) /* Tx FIFO Not Empty */ + +#define SAICR_ROR (1 << 6) /* Clear Rx FIFO Overrun Interrupt */ +#define SAICR_TUR (1 << 5) /* Clear Tx FIFO Underrun Interrupt */ + +#define SAIMR_ROR (1 << 6) /* Enable Rx FIFO Overrun Condition Interrupt */ +#define SAIMR_TUR (1 << 5) /* Enable Tx FIFO Underrun Condition Interrupt */ +#define SAIMR_RFS (1 << 4) /* Enable Rx FIFO Service Interrupt */ +#define SAIMR_TFS (1 << 3) /* Enable Tx FIFO Service Interrupt */ + struct pxa_i2s_port { u32 sadiv; u32 sacr0; @@ -44,7 +93,7 @@ static struct clk *clk_i2s; static struct pxa2xx_pcm_dma_params pxa2xx_i2s_pcm_stereo_out = { .name = "I2S PCM Stereo out", .dev_addr = __PREG(SADR), - .drcmr = &DRCMRTXSADR, + .drcmr = &DRCMR(3), .dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG | DCMD_BURST32 | DCMD_WIDTH4, }; @@ -52,7 +101,7 @@ static struct pxa2xx_pcm_dma_params pxa2xx_i2s_pcm_stereo_out = { static struct pxa2xx_pcm_dma_params pxa2xx_i2s_pcm_stereo_in = { .name = "I2S PCM Stereo in", .dev_addr = __PREG(SADR), - .drcmr = &DRCMRRXSADR, + .drcmr = &DRCMR(2), .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC | DCMD_BURST32 | DCMD_WIDTH4, }; @@ -65,11 +114,6 @@ static struct pxa2xx_gpio gpio_bus[] = { .frm = GPIO31_SYNC_I2S_MD, }, { /* I2S SoC Master */ -#ifdef CONFIG_PXA27x - .sys = GPIO113_I2S_SYSCLK_MD, -#else - .sys = GPIO32_SYSCLK_I2S_MD, -#endif .rx = GPIO29_SDATA_IN_I2S_MD, .tx = GPIO30_SDATA_OUT_I2S_MD, .clk = GPIO28_BITCLK_OUT_I2S_MD, @@ -343,6 +387,11 @@ static struct platform_driver pxa2xx_i2s_driver = { static int __init pxa2xx_i2s_init(void) { + if (cpu_is_pxa27x()) + gpio_bus[1].sys = GPIO113_I2S_SYSCLK_MD; + else + gpio_bus[1].sys = GPIO32_SYSCLK_I2S_MD; + clk_i2s = ERR_PTR(-ENOENT); return platform_driver_register(&pxa2xx_i2s_driver); } diff --git a/sound/soc/pxa/pxa2xx-pcm.c b/sound/soc/pxa/pxa2xx-pcm.c index 4345f38..afcd892 100644 --- a/sound/soc/pxa/pxa2xx-pcm.c +++ b/sound/soc/pxa/pxa2xx-pcm.c @@ -10,64 +10,14 @@ * published by the Free Software Foundation. */ -#include <linux/module.h> -#include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/slab.h> #include <linux/dma-mapping.h> #include <sound/core.h> -#include <sound/pcm.h> -#include <sound/pcm_params.h> #include <sound/soc.h> - -#include <asm/dma.h> -#include <mach/hardware.h> -#include <mach/pxa-regs.h> -#include <mach/audio.h> +#include <sound/pxa2xx-lib.h> #include "pxa2xx-pcm.h" - -static const struct snd_pcm_hardware pxa2xx_pcm_hardware = { - .info = SNDRV_PCM_INFO_MMAP | - SNDRV_PCM_INFO_MMAP_VALID | - SNDRV_PCM_INFO_INTERLEAVED | - SNDRV_PCM_INFO_PAUSE | - SNDRV_PCM_INFO_RESUME, - .formats = SNDRV_PCM_FMTBIT_S16_LE | - SNDRV_PCM_FMTBIT_S24_LE | - SNDRV_PCM_FMTBIT_S32_LE, - .period_bytes_min = 32, - .period_bytes_max = 8192 - 32, - .periods_min = 1, - .periods_max = PAGE_SIZE/sizeof(pxa_dma_desc), - .buffer_bytes_max = 128 * 1024, - .fifo_size = 32, -}; - -struct pxa2xx_runtime_data { - int dma_ch; - struct pxa2xx_pcm_dma_params *params; - pxa_dma_desc *dma_desc_array; - dma_addr_t dma_desc_array_phys; -}; - -static void pxa2xx_pcm_dma_irq(int dma_ch, void *dev_id) -{ - struct snd_pcm_substream *substream = dev_id; - struct pxa2xx_runtime_data *prtd = substream->runtime->private_data; - int dcsr; - - dcsr = DCSR(dma_ch); - DCSR(dma_ch) = dcsr & ~DCSR_STOPIRQEN; - - if (dcsr & DCSR_ENDINTR) { - snd_pcm_period_elapsed(substream); - } else { - printk(KERN_ERR "%s: DMA error on channel %d (DCSR=%#x)\n", - prtd->params->name, dma_ch, dcsr); - } -} +#include "../../arm/pxa2xx-pcm.h" static int pxa2xx_pcm_hw_params(struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) @@ -76,10 +26,6 @@ static int pxa2xx_pcm_hw_params(struct snd_pcm_substream *substream, struct pxa2xx_runtime_data *prtd = runtime->private_data; struct snd_soc_pcm_runtime *rtd = substream->private_data; struct pxa2xx_pcm_dma_params *dma = rtd->dai->cpu_dai->dma_data; - size_t totsize = params_buffer_bytes(params); - size_t period = params_period_bytes(params); - pxa_dma_desc *dma_desc; - dma_addr_t dma_buff_phys, next_desc_phys; int ret; /* return if this is a bufferless transfer e.g. @@ -106,42 +52,16 @@ static int pxa2xx_pcm_hw_params(struct snd_pcm_substream *substream, prtd->dma_ch = ret; } - snd_pcm_set_runtime_buffer(substream, &substream->dma_buffer); - runtime->dma_bytes = totsize; - - dma_desc = prtd->dma_desc_array; - next_desc_phys = prtd->dma_desc_array_phys; - dma_buff_phys = runtime->dma_addr; - do { - next_desc_phys += sizeof(pxa_dma_desc); - dma_desc->ddadr = next_desc_phys; - if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { - dma_desc->dsadr = dma_buff_phys; - dma_desc->dtadr = prtd->params->dev_addr; - } else { - dma_desc->dsadr = prtd->params->dev_addr; - dma_desc->dtadr = dma_buff_phys; - } - if (period > totsize) - period = totsize; - dma_desc->dcmd = prtd->params->dcmd | period | DCMD_ENDIRQEN; - dma_desc++; - dma_buff_phys += period; - } while (totsize -= period); - dma_desc[-1].ddadr = prtd->dma_desc_array_phys; - - return 0; + return __pxa2xx_pcm_hw_params(substream, params); } static int pxa2xx_pcm_hw_free(struct snd_pcm_substream *substream) { struct pxa2xx_runtime_data *prtd = substream->runtime->private_data; - if (prtd && prtd->params) - *prtd->params->drcmr = 0; + __pxa2xx_pcm_hw_free(substream); if (prtd->dma_ch) { - snd_pcm_set_runtime_buffer(substream, NULL); pxa_free_dma(prtd->dma_ch); prtd->dma_ch = 0; } @@ -149,188 +69,21 @@ static int pxa2xx_pcm_hw_free(struct snd_pcm_substream *substream) return 0; } -static int pxa2xx_pcm_prepare(struct snd_pcm_substream *substream) -{ - struct pxa2xx_runtime_data *prtd = substream->runtime->private_data; - - DCSR(prtd->dma_ch) &= ~DCSR_RUN; - DCSR(prtd->dma_ch) = 0; - DCMD(prtd->dma_ch) = 0; - *prtd->params->drcmr = prtd->dma_ch | DRCMR_MAPVLD; - - return 0; -} - -static int pxa2xx_pcm_trigger(struct snd_pcm_substream *substream, int cmd) -{ - struct pxa2xx_runtime_data *prtd = substream->runtime->private_data; - int ret = 0; - - switch (cmd) { - case SNDRV_PCM_TRIGGER_START: - DDADR(prtd->dma_ch) = prtd->dma_desc_array_phys; - DCSR(prtd->dma_ch) = DCSR_RUN; - break; - - case SNDRV_PCM_TRIGGER_STOP: - case SNDRV_PCM_TRIGGER_SUSPEND: - case SNDRV_PCM_TRIGGER_PAUSE_PUSH: - DCSR(prtd->dma_ch) &= ~DCSR_RUN; - break; - - case SNDRV_PCM_TRIGGER_RESUME: - DCSR(prtd->dma_ch) |= DCSR_RUN; - break; - case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: - DDADR(prtd->dma_ch) = prtd->dma_desc_array_phys; - DCSR(prtd->dma_ch) |= DCSR_RUN; - break; - - default: - ret = -EINVAL; - } - - return ret; -} - -static snd_pcm_uframes_t -pxa2xx_pcm_pointer(struct snd_pcm_substream *substream) -{ - struct snd_pcm_runtime *runtime = substream->runtime; - struct pxa2xx_runtime_data *prtd = runtime->private_data; - - dma_addr_t ptr = (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ? - DSADR(prtd->dma_ch) : DTADR(prtd->dma_ch); - snd_pcm_uframes_t x = bytes_to_frames(runtime, ptr - runtime->dma_addr); - - if (x == runtime->buffer_size) - x = 0; - return x; -} - -static int pxa2xx_pcm_open(struct snd_pcm_substream *substream) -{ - struct snd_pcm_runtime *runtime = substream->runtime; - struct pxa2xx_runtime_data *prtd; - int ret; - - snd_soc_set_runtime_hwparams(substream, &pxa2xx_pcm_hardware); - - /* - * For mysterious reasons (and despite what the manual says) - * playback samples are lost if the DMA count is not a multiple - * of the DMA burst size. Let's add a rule to enforce that. - */ - ret = snd_pcm_hw_constraint_step(runtime, 0, - SNDRV_PCM_HW_PARAM_PERIOD_BYTES, 32); - if (ret) - goto out; - - ret = snd_pcm_hw_constraint_step(runtime, 0, - SNDRV_PCM_HW_PARAM_BUFFER_BYTES, 32); - if (ret) - goto out; - - ret = snd_pcm_hw_constraint_integer(runtime, SNDRV_PCM_HW_PARAM_PERIODS); - if (ret < 0) - goto out; - - prtd = kzalloc(sizeof(struct pxa2xx_runtime_data), GFP_KERNEL); - if (prtd == NULL) { - ret = -ENOMEM; - goto out; - } - - prtd->dma_desc_array = - dma_alloc_writecombine(substream->pcm->card->dev, PAGE_SIZE, - &prtd->dma_desc_array_phys, GFP_KERNEL); - if (!prtd->dma_desc_array) { - ret = -ENOMEM; - goto err1; - } - - runtime->private_data = prtd; - return 0; - - err1: - kfree(prtd); - out: - return ret; -} - -static int pxa2xx_pcm_close(struct snd_pcm_substream *substream) -{ - struct snd_pcm_runtime *runtime = substream->runtime; - struct pxa2xx_runtime_data *prtd = runtime->private_data; - - dma_free_writecombine(substream->pcm->card->dev, PAGE_SIZE, - prtd->dma_desc_array, prtd->dma_desc_array_phys); - kfree(prtd); - return 0; -} - -static int pxa2xx_pcm_mmap(struct snd_pcm_substream *substream, - struct vm_area_struct *vma) -{ - struct snd_pcm_runtime *runtime = substream->runtime; - return dma_mmap_writecombine(substream->pcm->card->dev, vma, - runtime->dma_area, - runtime->dma_addr, - runtime->dma_bytes); -} - struct snd_pcm_ops pxa2xx_pcm_ops = { - .open = pxa2xx_pcm_open, - .close = pxa2xx_pcm_close, + .open = __pxa2xx_pcm_open, + .close = __pxa2xx_pcm_close, .ioctl = snd_pcm_lib_ioctl, .hw_params = pxa2xx_pcm_hw_params, .hw_free = pxa2xx_pcm_hw_free, - .prepare = pxa2xx_pcm_prepare, + .prepare = __pxa2xx_pcm_prepare, .trigger = pxa2xx_pcm_trigger, .pointer = pxa2xx_pcm_pointer, .mmap = pxa2xx_pcm_mmap, }; -static int pxa2xx_pcm_preallocate_dma_buffer(struct snd_pcm *pcm, int stream) -{ - struct snd_pcm_substream *substream = pcm->streams[stream].substream; - struct snd_dma_buffer *buf = &substream->dma_buffer; - size_t size = pxa2xx_pcm_hardware.buffer_bytes_max; - buf->dev.type = SNDRV_DMA_TYPE_DEV; - buf->dev.dev = pcm->card->dev; - buf->private_data = NULL; - buf->area = dma_alloc_writecombine(pcm->card->dev, size, - &buf->addr, GFP_KERNEL); - if (!buf->area) - return -ENOMEM; - buf->bytes = size; - return 0; -} - -static void pxa2xx_pcm_free_dma_buffers(struct snd_pcm *pcm) -{ - struct snd_pcm_substream *substream; - struct snd_dma_buffer *buf; - int stream; - - for (stream = 0; stream < 2; stream++) { - substream = pcm->streams[stream].substream; - if (!substream) - continue; - - buf = &substream->dma_buffer; - if (!buf->area) - continue; - - dma_free_writecombine(pcm->card->dev, buf->bytes, - buf->area, buf->addr); - buf->area = NULL; - } -} - static u64 pxa2xx_pcm_dmamask = DMA_32BIT_MASK; -int pxa2xx_pcm_new(struct snd_card *card, struct snd_soc_dai *dai, +static int pxa2xx_soc_pcm_new(struct snd_card *card, struct snd_soc_dai *dai, struct snd_pcm *pcm) { int ret = 0; @@ -360,7 +113,7 @@ int pxa2xx_pcm_new(struct snd_card *card, struct snd_soc_dai *dai, struct snd_soc_platform pxa2xx_soc_platform = { .name = "pxa2xx-audio", .pcm_ops = &pxa2xx_pcm_ops, - .pcm_new = pxa2xx_pcm_new, + .pcm_new = pxa2xx_soc_pcm_new, .pcm_free = pxa2xx_pcm_free_dma_buffers, }; EXPORT_SYMBOL_GPL(pxa2xx_soc_platform); diff --git a/sound/soc/pxa/pxa2xx-pcm.h b/sound/soc/pxa/pxa2xx-pcm.h index 54c9c75..60c3b20 100644 --- a/sound/soc/pxa/pxa2xx-pcm.h +++ b/sound/soc/pxa/pxa2xx-pcm.h @@ -13,21 +13,6 @@ #ifndef _PXA2XX_PCM_H #define _PXA2XX_PCM_H -struct pxa2xx_pcm_dma_params { - char *name; /* stream identifier */ - u32 dcmd; /* DMA descriptor dcmd field */ - volatile u32 *drcmr; /* the DMA request channel to use */ - u32 dev_addr; /* device physical address for DMA */ -}; - -struct pxa2xx_gpio { - u32 sys; - u32 rx; - u32 tx; - u32 clk; - u32 frm; -}; - /* platform data */ extern struct snd_soc_platform pxa2xx_soc_platform; diff --git a/sound/soc/pxa/spitz.c b/sound/soc/pxa/spitz.c index 37cb768..9a70b00 100644 --- a/sound/soc/pxa/spitz.c +++ b/sound/soc/pxa/spitz.c @@ -19,16 +19,15 @@ #include <linux/timer.h> #include <linux/interrupt.h> #include <linux/platform_device.h> +#include <linux/gpio.h> #include <sound/core.h> #include <sound/pcm.h> #include <sound/soc.h> #include <sound/soc-dapm.h> #include <asm/mach-types.h> -#include <asm/hardware/scoop.h> #include <mach/pxa-regs.h> #include <mach/hardware.h> -#include <mach/akita.h> #include <mach/spitz.h> #include "../codecs/wm8750.h" #include "pxa2xx-pcm.h" @@ -63,8 +62,8 @@ static void spitz_ext_control(struct snd_soc_codec *codec) snd_soc_dapm_disable_pin(codec, "Mic Jack"); snd_soc_dapm_disable_pin(codec, "Line Jack"); snd_soc_dapm_enable_pin(codec, "Headphone Jack"); - set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_MUTE_L); - set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_MUTE_R); + gpio_set_value(SPITZ_GPIO_MUTE_L, 1); + gpio_set_value(SPITZ_GPIO_MUTE_R, 1); break; case SPITZ_MIC: /* enable mic jack and bias, mute hp */ @@ -72,8 +71,8 @@ static void spitz_ext_control(struct snd_soc_codec *codec) snd_soc_dapm_disable_pin(codec, "Headset Jack"); snd_soc_dapm_disable_pin(codec, "Line Jack"); snd_soc_dapm_enable_pin(codec, "Mic Jack"); - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_MUTE_L); - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_MUTE_R); + gpio_set_value(SPITZ_GPIO_MUTE_L, 0); + gpio_set_value(SPITZ_GPIO_MUTE_R, 0); break; case SPITZ_LINE: /* enable line jack, disable mic bias and mute hp */ @@ -81,8 +80,8 @@ static void spitz_ext_control(struct snd_soc_codec *codec) snd_soc_dapm_disable_pin(codec, "Headset Jack"); snd_soc_dapm_disable_pin(codec, "Mic Jack"); snd_soc_dapm_enable_pin(codec, "Line Jack"); - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_MUTE_L); - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_MUTE_R); + gpio_set_value(SPITZ_GPIO_MUTE_L, 0); + gpio_set_value(SPITZ_GPIO_MUTE_R, 0); break; case SPITZ_HEADSET: /* enable and unmute headset jack enable mic bias, mute L hp */ @@ -90,8 +89,8 @@ static void spitz_ext_control(struct snd_soc_codec *codec) snd_soc_dapm_enable_pin(codec, "Mic Jack"); snd_soc_dapm_disable_pin(codec, "Line Jack"); snd_soc_dapm_enable_pin(codec, "Headset Jack"); - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_MUTE_L); - set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_MUTE_R); + gpio_set_value(SPITZ_GPIO_MUTE_L, 0); + gpio_set_value(SPITZ_GPIO_MUTE_R, 1); break; case SPITZ_HP_OFF: @@ -100,8 +99,8 @@ static void spitz_ext_control(struct snd_soc_codec *codec) snd_soc_dapm_disable_pin(codec, "Headset Jack"); snd_soc_dapm_disable_pin(codec, "Mic Jack"); snd_soc_dapm_disable_pin(codec, "Line Jack"); - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_MUTE_L); - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_MUTE_R); + gpio_set_value(SPITZ_GPIO_MUTE_L, 0); + gpio_set_value(SPITZ_GPIO_MUTE_R, 0); break; } snd_soc_dapm_sync(codec); @@ -215,23 +214,14 @@ static int spitz_set_spk(struct snd_kcontrol *kcontrol, static int spitz_mic_bias(struct snd_soc_dapm_widget *w, struct snd_kcontrol *k, int event) { - if (machine_is_borzoi() || machine_is_spitz()) { - if (SND_SOC_DAPM_EVENT_ON(event)) - set_scoop_gpio(&spitzscoop2_device.dev, - SPITZ_SCP2_MIC_BIAS); - else - reset_scoop_gpio(&spitzscoop2_device.dev, - SPITZ_SCP2_MIC_BIAS); - } + if (machine_is_borzoi() || machine_is_spitz()) + gpio_set_value(SPITZ_GPIO_MIC_BIAS, + SND_SOC_DAPM_EVENT_ON(event)); + + if (machine_is_akita()) + gpio_set_value(AKITA_GPIO_MIC_BIAS, + SND_SOC_DAPM_EVENT_ON(event)); - if (machine_is_akita()) { - if (SND_SOC_DAPM_EVENT_ON(event)) - akita_set_ioexp(&akitaioexp_device.dev, - AKITA_IOEXP_MIC_BIAS); - else - akita_reset_ioexp(&akitaioexp_device.dev, - AKITA_IOEXP_MIC_BIAS); - } return 0; } @@ -337,6 +327,7 @@ static struct snd_soc_machine snd_soc_machine_spitz = { /* spitz audio private data */ static struct wm8750_setup_data spitz_wm8750_setup = { + .i2c_bus = 0, .i2c_address = 0x1b, }; |