diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/linux/ieee80211.h | 4 | ||||
| -rw-r--r-- | include/net/cfg80211.h | 23 | ||||
| -rw-r--r-- | include/uapi/linux/nl80211.h | 28 |
3 files changed, 54 insertions, 1 deletions
diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h index 61a09f0..b1be39c 100644 --- a/include/linux/ieee80211.h +++ b/include/linux/ieee80211.h @@ -166,8 +166,12 @@ static inline u16 ieee80211_sn_sub(u16 sn1, u16 sn2) #define IEEE80211_MAX_MESH_ID_LEN 32 +#define IEEE80211_FIRST_TSPEC_TSID 8 #define IEEE80211_NUM_TIDS 16 +/* number of user priorities 802.11 uses */ +#define IEEE80211_NUM_UPS 8 + #define IEEE80211_QOS_CTL_LEN 2 /* 1d tag mask */ #define IEEE80211_QOS_CTL_TAG1D_MASK 0x0007 diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index c2c710c..a13beab1 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -2318,6 +2318,17 @@ struct cfg80211_qos_map { * @set_ap_chanwidth: Set the AP (including P2P GO) mode channel width for the * given interface This is used e.g. for dynamic HT 20/40 MHz channel width * changes during the lifetime of the BSS. + * + * @add_tx_ts: validate (if admitted_time is 0) or add a TX TS to the device + * with the given parameters; action frame exchange has been handled by + * userspace so this just has to modify the TX path to take the TS into + * account. + * If the admitted time is 0 just validate the parameters to make sure + * the session can be created at all; it is valid to just always return + * success for that but that may result in inefficient behaviour (handshake + * with the peer followed by immediate teardown when the addition is later + * rejected) + * @del_tx_ts: remove an existing TX TS */ struct cfg80211_ops { int (*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow); @@ -2558,6 +2569,12 @@ struct cfg80211_ops { int (*set_ap_chanwidth)(struct wiphy *wiphy, struct net_device *dev, struct cfg80211_chan_def *chandef); + + int (*add_tx_ts)(struct wiphy *wiphy, struct net_device *dev, + u8 tsid, const u8 *peer, u8 user_prio, + u16 admitted_time); + int (*del_tx_ts)(struct wiphy *wiphy, struct net_device *dev, + u8 tsid, const u8 *peer); }; /* @@ -2604,9 +2621,13 @@ struct cfg80211_ops { * @WIPHY_FLAG_SUPPORTS_5_10_MHZ: Device supports 5 MHz and 10 MHz channels. * @WIPHY_FLAG_HAS_CHANNEL_SWITCH: Device supports channel switch in * beaconing mode (AP, IBSS, Mesh, ...). + * @WIPHY_FLAG_SUPPORTS_WMM_ADMISSION: the device supports setting up WMM + * TSPEC sessions (TID aka TSID 0-7) with the NL80211_CMD_ADD_TX_TS + * command. Standard IEEE 802.11 TSPEC setup is not yet supported, it + * needs to be able to handle Block-Ack agreements and other things. */ enum wiphy_flags { - /* use hole at 0 */ + WIPHY_FLAG_SUPPORTS_WMM_ADMISSION = BIT(0), /* use hole at 1 */ /* use hole at 2 */ WIPHY_FLAG_NETNS_OK = BIT(3), diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index 29c4399..e5b8caf 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -722,6 +722,22 @@ * QoS mapping is relevant for IP packets, it is only valid during an * association. This is cleared on disassociation and AP restart. * + * @NL80211_CMD_ADD_TX_TS: Ask the kernel to add a traffic stream for the given + * %NL80211_ATTR_TSID and %NL80211_ATTR_MAC with %NL80211_ATTR_USER_PRIO + * and %NL80211_ATTR_ADMITTED_TIME parameters. + * Note that the action frame handshake with the AP shall be handled by + * userspace via the normal management RX/TX framework, this only sets + * up the TX TS in the driver/device. + * If the admitted time attribute is not added then the request just checks + * if a subsequent setup could be successful, the intent is to use this to + * avoid setting up a session with the AP when local restrictions would + * make that impossible. However, the subsequent "real" setup may still + * fail even if the check was successful. + * @NL80211_CMD_DEL_TX_TS: Remove an existing TS with the %NL80211_ATTR_TSID + * and %NL80211_ATTR_MAC parameters. It isn't necessary to call this + * before removing a station entry entirely, or before disassociating + * or similar, cleanup will happen in the driver/device in this case. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -893,6 +909,9 @@ enum nl80211_commands { NL80211_CMD_SET_QOS_MAP, + NL80211_CMD_ADD_TX_TS, + NL80211_CMD_DEL_TX_TS, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -1611,6 +1630,11 @@ enum nl80211_commands { * drivers to indicate dynack capability. Dynack is automatically disabled * setting valid value for coverage class. * + * @NL80211_ATTR_TSID: a TSID value (u8 attribute) + * @NL80211_ATTR_USER_PRIO: user priority value (u8 attribute) + * @NL80211_ATTR_ADMITTED_TIME: admitted time in units of 32 microseconds + * (per second) (u16 attribute) + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ @@ -1957,6 +1981,10 @@ enum nl80211_attrs { NL80211_ATTR_WIPHY_DYN_ACK, + NL80211_ATTR_TSID, + NL80211_ATTR_USER_PRIO, + NL80211_ATTR_ADMITTED_TIME, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, |
