diff options
Diffstat (limited to 'include')
-rw-r--r-- | include/net/cfg80211.h | 21 | ||||
-rw-r--r-- | include/uapi/linux/nl80211.h | 47 |
2 files changed, 67 insertions, 1 deletions
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 68dca3d..9898e1f 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -2314,6 +2314,19 @@ struct cfg80211_qos_map { }; /** + * struct cfg80211_nan_conf - NAN configuration + * + * This struct defines NAN configuration parameters + * + * @master_pref: master preference (1 - 255) + * @dual: dual band operation mode, see &enum nl80211_nan_dual_band_conf + */ +struct cfg80211_nan_conf { + u8 master_pref; + u8 dual; +}; + +/** * struct cfg80211_ops - backend description for wireless configuration * * This struct is registered by fullmac card drivers and/or wireless stacks @@ -2601,6 +2614,8 @@ struct cfg80211_qos_map { * and returning to the base channel for communication with the AP. * @tdls_cancel_channel_switch: Stop channel-switching with a TDLS peer. Both * peers must be on the base channel when the call completes. + * @start_nan: Start the NAN interface. + * @stop_nan: Stop the NAN interface. */ struct cfg80211_ops { int (*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow); @@ -2866,6 +2881,9 @@ struct cfg80211_ops { void (*tdls_cancel_channel_switch)(struct wiphy *wiphy, struct net_device *dev, const u8 *addr); + int (*start_nan)(struct wiphy *wiphy, struct wireless_dev *wdev, + struct cfg80211_nan_conf *conf); + void (*stop_nan)(struct wiphy *wiphy, struct wireless_dev *wdev); }; /* @@ -3626,6 +3644,7 @@ struct cfg80211_cached_keys; * beacons, 0 when not valid * @address: The address for this device, valid only if @netdev is %NULL * @p2p_started: true if this is a P2P Device that has been started + * @nan_started: true if this is a NAN interface that has been started * @cac_started: true if DFS channel availability check has been started * @cac_start_time: timestamp (jiffies) when the dfs state was entered. * @cac_time_ms: CAC time in ms @@ -3657,7 +3676,7 @@ struct wireless_dev { struct mutex mtx; - bool use_4addr, p2p_started; + bool use_4addr, p2p_started, nan_started; u8 address[ETH_ALEN] __aligned(sizeof(u16)); diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index ec10d1b..98fd3ec 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -838,6 +838,16 @@ * not running. The driver indicates the status of the scan through * cfg80211_scan_done(). * + * @NL80211_CMD_START_NAN: Start NAN operation, identified by its + * %NL80211_ATTR_WDEV interface. This interface must have been previously + * created with %NL80211_CMD_NEW_INTERFACE. After it has been started, the + * NAN interface will create or join a cluster. This command must have a + * valid %NL80211_ATTR_NAN_MASTER_PREF attribute and optional + * %NL80211_ATTR_NAN_DUAL attributes. + * After this command NAN functions can be added. + * @NL80211_CMD_STOP_NAN: Stop the NAN operation, identified by + * its %NL80211_ATTR_WDEV interface. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -1026,6 +1036,9 @@ enum nl80211_commands { NL80211_CMD_ABORT_SCAN, + NL80211_CMD_START_NAN, + NL80211_CMD_STOP_NAN, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -1739,6 +1752,12 @@ enum nl80211_commands { * regulatory indoor configuration would be owned by the netlink socket * that configured the indoor setting, and the indoor operation would be * cleared when the socket is closed. + * If set during NAN interface creation, the interface will be destroyed + * if the socket is closed just like any other interface. Moreover, only + * the netlink socket that created the interface will be allowed to add + * and remove functions. NAN notifications will be sent in unicast to that + * socket. Without this attribute, any socket can add functions and the + * notifications will be sent to the %NL80211_MCGRP_NAN multicast group. * * @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is * the TDLS link initiator. @@ -1873,6 +1892,14 @@ enum nl80211_commands { * @NL80211_ATTR_MESH_PEER_AID: Association ID for the mesh peer (u16). This is * used to pull the stored data for mesh peer in power save state. * + * @NL80211_ATTR_NAN_MASTER_PREF: the master preference to be used by + * %NL80211_CMD_START_NAN. Its type is u8 and it can't be 0. + * Also, values 1 and 255 are reserved for certification purposes and + * should not be used during a normal device operation. + * @NL80211_ATTR_NAN_DUAL: NAN dual band operation config (see + * &enum nl80211_nan_dual_band_conf). This attribute is used with + * %NL80211_CMD_START_NAN. + * * @NUM_NL80211_ATTR: total number of nl80211_attrs available * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use @@ -2267,6 +2294,9 @@ enum nl80211_attrs { NL80211_ATTR_MESH_PEER_AID, + NL80211_ATTR_NAN_MASTER_PREF, + NL80211_ATTR_NAN_DUAL, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -2345,6 +2375,7 @@ enum nl80211_attrs { * commands to create and destroy one * @NL80211_IF_TYPE_OCB: Outside Context of a BSS * This mode corresponds to the MIB variable dot11OCBActivated=true + * @NL80211_IFTYPE_NAN: NAN device interface type (not a netdev) * @NL80211_IFTYPE_MAX: highest interface type number currently defined * @NUM_NL80211_IFTYPES: number of defined interface types * @@ -2365,6 +2396,7 @@ enum nl80211_iftype { NL80211_IFTYPE_P2P_GO, NL80211_IFTYPE_P2P_DEVICE, NL80211_IFTYPE_OCB, + NL80211_IFTYPE_NAN, /* keep last */ NUM_NL80211_IFTYPES, @@ -4870,4 +4902,19 @@ enum nl80211_bss_select_attr { NL80211_BSS_SELECT_ATTR_MAX = __NL80211_BSS_SELECT_ATTR_AFTER_LAST - 1 }; +/** + * enum nl80211_nan_dual_band_conf - NAN dual band configuration + * + * Defines the NAN dual band mode of operation + * + * @NL80211_NAN_BAND_DEFAULT: device default mode + * @NL80211_NAN_BAND_2GHZ: 2.4GHz mode + * @NL80211_NAN_BAND_5GHZ: 5GHz mode + */ +enum nl80211_nan_dual_band_conf { + NL80211_NAN_BAND_DEFAULT = 1 << 0, + NL80211_NAN_BAND_2GHZ = 1 << 1, + NL80211_NAN_BAND_5GHZ = 1 << 2, +}; + #endif /* __LINUX_NL80211_H */ |