diff options
Diffstat (limited to 'include/net')
| -rw-r--r-- | include/net/mac80211.h | 151 |
1 files changed, 95 insertions, 56 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 5ff4555..855754d 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -467,7 +467,6 @@ enum ieee80211_if_types { * @mac_addr: pointer to MAC address of the interface. This pointer is valid * until the interface is removed (i.e. it cannot be used after * remove_interface() callback was called for this interface). - * This pointer will be %NULL for monitor interfaces, be careful. * * This structure is used in add_interface() and remove_interface() * callbacks of &struct ieee80211_hw. @@ -653,13 +652,9 @@ struct ieee80211_hw { /* hole at 8 */ - /* Device is capable of performing full monitor mode even during - * normal operation. */ -#define IEEE80211_HW_MONITOR_DURING_OPER (1<<9) +/* hole at 9 */ - /* Device does not need BSSID filter set to broadcast in order to - * receive all probe responses while scanning */ -#define IEEE80211_HW_NO_PROBE_FILTERING (1<<10) +/* hole at 10 */ /* Channels are already configured to the default regulatory domain * specified in the device's EEPROM */ @@ -694,6 +689,39 @@ static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr) memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN); } +/* + * flags for change_filter_flags() + * + * Note that e.g. if PROMISC_IN_BSS is unset then + * you should still do MAC address filtering if + * possible even if OTHER_BSS is set to indicate + * no BSSID filtering should be done. + */ +/* + * promiscuous mode within your BSS, + * think of the BSS as your network segment and then this corresponds + * to the regular ethernet device promiscuous mode + */ +#define FIF_PROMISC_IN_BSS 0x01 +/* show all multicast frames */ +#define FIF_ALLMULTI 0x02 +/* show frames with failed FCS, but set RX_FLAG_FAILED_FCS_CRC for them */ +#define FIF_FCSFAIL 0x04 +/* show frames with failed PLCP CRC, but set RX_FLAG_FAILED_PLCP_CRC for them */ +#define FIF_PLCPFAIL 0x08 +/* + * This flag is set during scanning to indicate to the hardware + * that it should not filter beacons or probe responses by BSSID. + */ +#define FIF_BCN_PRBRESP_PROMISC 0x10 +/* + * show control frames, if PROMISC_IN_BSS is not set then + * only those addressed to this station + */ +#define FIF_CONTROL 0x20 +/* show frames from other BSSes */ +#define FIF_OTHER_BSS 0x40 + /* Configuration block used by the low-level driver to tell the 802.11 code * about supported hardware features and to pass function pointers to callback * functions. */ @@ -706,32 +734,55 @@ struct ieee80211_ops { int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb, struct ieee80211_tx_control *control); - /* Handler that is called when any netdevice attached to the hardware - * device is set UP for the first time. This can be used, e.g., to - * enable interrupts and beacon sending. */ - int (*open)(struct ieee80211_hw *hw); - - /* Handler that is called when the last netdevice attached to the - * hardware device is set DOWN. This can be used, e.g., to disable - * interrupts and beacon sending. */ - int (*stop)(struct ieee80211_hw *hw); - - /* Handler for asking a driver if a new interface can be added (or, - * more exactly, set UP). If the handler returns zero, the interface - * is added. Driver should perform any initialization it needs prior - * to returning zero. By returning non-zero addition of the interface - * is inhibited. Unless monitor_during_oper is set, it is guaranteed - * that monitor interfaces and normal interfaces are mutually - * exclusive. If assigned, the open() handler is called after - * add_interface() if this is the first device added. The - * add_interface() callback has to be assigned because it is the only - * way to obtain the requested MAC address for any interface. + /* + * Called before the first netdevice attached to the hardware + * is enabled. This should turn on the hardware and must turn on + * frame reception (for possibly enabled monitor interfaces.) + * Returns negative error codes, these may be seen in userspace, + * or zero. + * When the device is started it should not have a MAC address + * to avoid acknowledging frames before a non-monitor device + * is added. + * + * Must be implemented. + */ + int (*start)(struct ieee80211_hw *hw); + + /* + * Called after last netdevice attached to the hardware + * is disabled. This should turn off the hardware (at least + * it must turn off frame reception.) + * May be called right after add_interface if that rejects + * an interface. + * + * Must be implemented. + */ + void (*stop)(struct ieee80211_hw *hw); + + /* + * Called when a netdevice attached to the hardware is enabled. + * Because it is not called for monitor mode devices, open() + * and stop() must be implemented. + * The driver should perform any initialization it needs before + * the device can be enabled. The initial configuration for the + * interface is given in the conf parameter. + * + * Must be implemented. */ int (*add_interface)(struct ieee80211_hw *hw, struct ieee80211_if_init_conf *conf); - /* Notify a driver that an interface is going down. The stop() handler - * is called prior to this if this is a last interface. */ + /* + * Notifies a driver that an interface is going down. The stop() handler + * is called after this if it is the last interface and no monitor + * interfaces are present. + * When all interfaces are removed, the MAC address in the hardware + * must be cleared so the device no longer acknowledges packets, + * the mac_addr member of the conf structure is, however, set to the + * MAC address of the device going away. + * + * Hence, this callback must be implemented. + */ void (*remove_interface)(struct ieee80211_hw *hw, struct ieee80211_if_init_conf *conf); @@ -744,15 +795,21 @@ struct ieee80211_ops { int (*config_interface)(struct ieee80211_hw *hw, int if_id, struct ieee80211_if_conf *conf); - /* ieee80211 drivers do not have access to the &struct net_device - * that is (are) connected with their device. Hence (and because - * we need to combine the multicast lists and flags for multiple - * virtual interfaces), they cannot assign set_multicast_list. - * The parameters here replace dev->flags and dev->mc_count, - * dev->mc_list is replaced by calling ieee80211_get_mc_list_item. - * Must be atomic. */ - void (*set_multicast_list)(struct ieee80211_hw *hw, - unsigned short flags, int mc_count); + /* + * Configure the device's RX filter. + * + * The multicast address filter must be changed if the hardware flags + * indicate that one is present. + * + * All unsupported flags in 'total_flags' must be cleared, + * clear all bits except those you honoured. + * + * The callback must be implemented and must be atomic. + */ + void (*configure_filter)(struct ieee80211_hw *hw, + unsigned int changed_flags, + unsigned int *total_flags, + int mc_count, struct dev_addr_list *mc_list); /* Set TIM bit handler. If the hardware/firmware takes care of beacon * generation, IEEE 802.11 code uses this function to tell the @@ -1155,24 +1212,6 @@ void ieee80211_stop_queues(struct ieee80211_hw *hw); */ void ieee80211_wake_queues(struct ieee80211_hw *hw); -/** - * ieee80211_get_mc_list_item - iteration over items in multicast list - * @hw: pointer as obtained from ieee80211_alloc_hw(). - * @prev: value returned by previous call to ieee80211_get_mc_list_item() or - * NULL to start a new iteration. - * @ptr: pointer to buffer of void * type for internal usage of - * ieee80211_get_mc_list_item(). - * - * Iterates over items in multicast list of given device. To get the first - * item, pass NULL in @prev and in *@ptr. In subsequent calls, pass the - * value returned by previous call in @prev. Don't alter *@ptr during - * iteration. When there are no more items, NULL is returned. - */ -struct dev_mc_list * -ieee80211_get_mc_list_item(struct ieee80211_hw *hw, - struct dev_mc_list *prev, - void **ptr); - /* called by driver to notify scan status completed */ void ieee80211_scan_completed(struct ieee80211_hw *hw); |
