diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 138 |
1 files changed, 128 insertions, 10 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 0ad1f47..5f203a6 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -263,6 +263,7 @@ struct ieee80211_vif_chanctx_switch { * @BSS_CHANGED_BANDWIDTH: The bandwidth used by this interface changed, * note that this is only called when it changes after the channel * context had been assigned. + * @BSS_CHANGED_OCB: OCB join status changed */ enum ieee80211_bss_change { BSS_CHANGED_ASSOC = 1<<0, @@ -287,6 +288,7 @@ enum ieee80211_bss_change { BSS_CHANGED_P2P_PS = 1<<19, BSS_CHANGED_BEACON_INFO = 1<<20, BSS_CHANGED_BANDWIDTH = 1<<21, + BSS_CHANGED_OCB = 1<<22, /* when adding here, make sure to change ieee80211_reconfig */ }; @@ -739,7 +741,8 @@ struct ieee80211_tx_info { u8 ampdu_ack_len; u8 ampdu_len; u8 antenna; - void *status_driver_data[21 / sizeof(void *)]; + u16 tx_time; + void *status_driver_data[19 / sizeof(void *)]; } status; struct { struct ieee80211_tx_rate driver_rates[ @@ -1117,6 +1120,8 @@ struct ieee80211_conf { * Function (TSF) timer when the frame containing the channel switch * announcement was received. This is simply the rx.mactime parameter * the driver passed into mac80211. + * @device_timestamp: arbitrary timestamp for the device, this is the + * rx.device_timestamp parameter the driver passed to mac80211. * @block_tx: Indicates whether transmission must be blocked before the * scheduled channel switch, as indicated by the AP. * @chandef: the new channel to switch to @@ -1124,6 +1129,7 @@ struct ieee80211_conf { */ struct ieee80211_channel_switch { u64 timestamp; + u32 device_timestamp; bool block_tx; struct cfg80211_chan_def chandef; u8 count; @@ -1423,6 +1429,8 @@ struct ieee80211_sta_rates { * @smps_mode: current SMPS mode (off, static or dynamic) * @rates: rate control selection table * @tdls: indicates whether the STA is a TDLS peer + * @tdls_initiator: indicates the STA is an initiator of the TDLS link. Only + * valid if the STA is a TDLS peer in the first place. */ struct ieee80211_sta { u32 supp_rates[IEEE80211_NUM_BANDS]; @@ -1438,6 +1446,7 @@ struct ieee80211_sta { enum ieee80211_smps_mode smps_mode; struct ieee80211_sta_rates __rcu *rates; bool tdls; + bool tdls_initiator; /* must be last */ u8 drv_priv[0] __aligned(sizeof(void *)); @@ -1576,6 +1585,10 @@ struct ieee80211_tx_control { * a virtual monitor interface when monitor interfaces are the only * active interfaces. * + * @IEEE80211_HW_NO_AUTO_VIF: The driver would like for no wlanX to + * be created. It is expected user-space will create vifs as + * desired (and thus have them named as desired). + * * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface * queue mapping in order to use different queues (not just one per AC) * for different virtual interfaces. See the doc section on HW queue @@ -1622,7 +1635,8 @@ enum ieee80211_hw_flags { IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12, IEEE80211_HW_MFP_CAPABLE = 1<<13, IEEE80211_HW_WANT_MONITOR_VIF = 1<<14, - /* free slots */ + IEEE80211_HW_NO_AUTO_VIF = 1<<15, + /* free slot */ IEEE80211_HW_SUPPORTS_UAPSD = 1<<17, IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18, IEEE80211_HW_CONNECTION_MONITOR = 1<<19, @@ -2375,6 +2389,22 @@ enum ieee80211_roc_type { }; /** + * enum ieee80211_reconfig_complete_type - reconfig type + * + * This enum is used by the reconfig_complete() callback to indicate what + * reconfiguration type was completed. + * + * @IEEE80211_RECONFIG_TYPE_RESTART: hw restart type + * (also due to resume() callback returning 1) + * @IEEE80211_RECONFIG_TYPE_SUSPEND: suspend type (regardless + * of wowlan configuration) + */ +enum ieee80211_reconfig_type { + IEEE80211_RECONFIG_TYPE_RESTART, + IEEE80211_RECONFIG_TYPE_SUSPEND, +}; + +/** * struct ieee80211_ops - callbacks from mac80211 to the driver * * This structure contains various callbacks that the driver may @@ -2809,11 +2839,11 @@ enum ieee80211_roc_type { * disabled/enabled via @bss_info_changed. * @stop_ap: Stop operation on the AP interface. * - * @restart_complete: Called after a call to ieee80211_restart_hw(), when the - * reconfiguration has completed. This can help the driver implement the - * reconfiguration step. Also called when reconfiguring because the - * driver's resume function returned 1, as this is just like an "inline" - * hardware restart. This callback may sleep. + * @reconfig_complete: Called after a call to ieee80211_restart_hw() and + * during resume, when the reconfiguration has completed. + * This can help the driver implement the reconfiguration step (and + * indicate mac80211 is ready to receive frames). + * This callback may sleep. * * @ipv6_addr_change: IPv6 address assignment on the given interface changed. * Currently, this is only called for managed or P2P client interfaces. @@ -2829,6 +2859,13 @@ enum ieee80211_roc_type { * transmitted and then call ieee80211_csa_finish(). * If the CSA count starts as zero or 1, this function will not be called, * since there won't be any time to beacon before the switch anyway. + * @pre_channel_switch: This is an optional callback that is called + * before a channel switch procedure is started (ie. when a STA + * gets a CSA or an userspace initiated channel-switch), allowing + * the driver to prepare for the channel switch. + * @post_channel_switch: This is an optional callback that is called + * after a channel switch procedure is completed, allowing the + * driver to go back to a normal configuration. * * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all * information in bss_conf is set up and the beacon can be retrieved. A @@ -2838,6 +2875,9 @@ enum ieee80211_roc_type { * @get_expected_throughput: extract the expected throughput towards the * specified station. The returned value is expressed in Kbps. It returns 0 * if the RC algorithm does not have proper data to provide. + * + * @get_txpower: get current maximum tx power (in dBm) based on configuration + * and hardware limits. */ struct ieee80211_ops { void (*tx)(struct ieee80211_hw *hw, @@ -2959,6 +2999,7 @@ struct ieee80211_ops { void (*flush)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, u32 queues, bool drop); void (*channel_switch)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, struct ieee80211_channel_switch *ch_switch); int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant); int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant); @@ -3025,7 +3066,8 @@ struct ieee80211_ops { int n_vifs, enum ieee80211_chanctx_switch_mode mode); - void (*restart_complete)(struct ieee80211_hw *hw); + void (*reconfig_complete)(struct ieee80211_hw *hw, + enum ieee80211_reconfig_type reconfig_type); #if IS_ENABLED(CONFIG_IPV6) void (*ipv6_addr_change)(struct ieee80211_hw *hw, @@ -3035,14 +3077,42 @@ struct ieee80211_ops { void (*channel_switch_beacon)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct cfg80211_chan_def *chandef); + int (*pre_channel_switch)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_channel_switch *ch_switch); + + int (*post_channel_switch)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); u32 (*get_expected_throughput)(struct ieee80211_sta *sta); + int (*get_txpower)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + int *dbm); }; /** - * ieee80211_alloc_hw - Allocate a new hardware device + * ieee80211_alloc_hw_nm - Allocate a new hardware device + * + * This must be called once for each hardware device. The returned pointer + * must be used to refer to this device when calling other functions. + * mac80211 allocates a private data area for the driver pointed to by + * @priv in &struct ieee80211_hw, the size of this area is given as + * @priv_data_len. + * + * @priv_data_len: length of private data + * @ops: callbacks for this device + * @requested_name: Requested name for this device. + * NULL is valid value, and means use the default naming (phy%d) + * + * Return: A pointer to the new hardware device, or %NULL on error. + */ +struct ieee80211_hw *ieee80211_alloc_hw_nm(size_t priv_data_len, + const struct ieee80211_ops *ops, + const char *requested_name); + +/** + * ieee80211_alloc_hw - Allocate a new hardware device * * This must be called once for each hardware device. The returned pointer * must be used to refer to this device when calling other functions. @@ -3055,8 +3125,12 @@ struct ieee80211_ops { * * Return: A pointer to the new hardware device, or %NULL on error. */ +static inline struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, - const struct ieee80211_ops *ops); + const struct ieee80211_ops *ops) +{ + return ieee80211_alloc_hw_nm(priv_data_len, ops, NULL); +} /** * ieee80211_register_hw - Register hardware device @@ -4172,6 +4246,22 @@ void ieee80211_iterate_active_interfaces_rtnl(struct ieee80211_hw *hw, void *data); /** + * ieee80211_iterate_stations_atomic - iterate stations + * + * This function iterates over all stations associated with a given + * hardware that are currently uploaded to the driver and calls the callback + * function for them. + * This function requires the iterator callback function to be atomic, + * + * @hw: the hardware struct of which the interfaces should be iterated over + * @iterator: the iterator function to call, cannot sleep + * @data: first argument of the iterator function + */ +void ieee80211_iterate_stations_atomic(struct ieee80211_hw *hw, + void (*iterator)(void *data, + struct ieee80211_sta *sta), + void *data); +/** * ieee80211_queue_work - add work onto the mac80211 workqueue * * Drivers and mac80211 use this to add work onto the mac80211 workqueue. @@ -4888,4 +4978,32 @@ void ieee80211_update_p2p_noa(struct ieee80211_noa_data *data, u32 tsf); void ieee80211_tdls_oper_request(struct ieee80211_vif *vif, const u8 *peer, enum nl80211_tdls_operation oper, u16 reason_code, gfp_t gfp); + +/** + * ieee80211_ie_split - split an IE buffer according to ordering + * + * @ies: the IE buffer + * @ielen: the length of the IE buffer + * @ids: an array with element IDs that are allowed before + * the split + * @n_ids: the size of the element ID array + * @offset: offset where to start splitting in the buffer + * + * This function splits an IE buffer by updating the @offset + * variable to point to the location where the buffer should be + * split. + * + * It assumes that the given IE buffer is well-formed, this + * has to be guaranteed by the caller! + * + * It also assumes that the IEs in the buffer are ordered + * correctly, if not the result of using this function will not + * be ordered correctly either, i.e. it does no reordering. + * + * The function returns the offset where the next part of the + * buffer starts, which may be @ielen if the entire (remainder) + * of the buffer should be used. + */ +size_t ieee80211_ie_split(const u8 *ies, size_t ielen, + const u8 *ids, int n_ids, size_t offset); #endif /* MAC80211_H */ |
