diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 78 |
1 files changed, 70 insertions, 8 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 451c1bf..2c78997 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -1113,7 +1113,9 @@ enum ieee80211_vif_flags { * @addr: address of this interface * @p2p: indicates whether this AP or STA interface is a p2p * interface, i.e. a GO or p2p-sta respectively - * @csa_active: marks whether a channel switch is going on + * @csa_active: marks whether a channel switch is going on. Internally it is + * write-protected by sdata_lock and local->mtx so holding either is fine + * for read access. * @driver_flags: flags/capabilities the driver has for this interface, * these need to be set (or cleared) when the interface is added * or, if supported by the driver, the interface type is changed @@ -1374,6 +1376,7 @@ struct ieee80211_sta_rates { * the station moves to associated state. * @smps_mode: current SMPS mode (off, static or dynamic) * @rates: rate control selection table + * @tdls: indicates whether the STA is a TDLS peer */ struct ieee80211_sta { u32 supp_rates[IEEE80211_NUM_BANDS]; @@ -1388,6 +1391,7 @@ struct ieee80211_sta { enum ieee80211_sta_rx_bandwidth bandwidth; enum ieee80211_smps_mode smps_mode; struct ieee80211_sta_rates __rcu *rates; + bool tdls; /* must be last */ u8 drv_priv[0] __aligned(sizeof(void *)); @@ -2765,6 +2769,10 @@ enum ieee80211_roc_type { * information in bss_conf is set up and the beacon can be retrieved. A * channel context is bound before this is called. * @leave_ibss: Leave the IBSS again. + * + * @get_expected_throughput: extract the expected throughput towards the + * specified station. The returned value is expressed in Kbps. It returns 0 + * if the RC algorithm does not have proper data to provide. */ struct ieee80211_ops { void (*tx)(struct ieee80211_hw *hw, @@ -2958,6 +2966,7 @@ struct ieee80211_ops { int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + u32 (*get_expected_throughput)(struct ieee80211_sta *sta); }; /** @@ -3407,6 +3416,47 @@ void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, */ void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets); +#define IEEE80211_MAX_CSA_COUNTERS_NUM 2 + +/** + * struct ieee80211_mutable_offsets - mutable beacon offsets + * @tim_offset: position of TIM element + * @tim_length: size of TIM element + * @csa_counter_offs: array of IEEE80211_MAX_CSA_COUNTERS_NUM offsets + * to CSA counters. This array can contain zero values which + * should be ignored. + */ +struct ieee80211_mutable_offsets { + u16 tim_offset; + u16 tim_length; + + u16 csa_counter_offs[IEEE80211_MAX_CSA_COUNTERS_NUM]; +}; + +/** + * ieee80211_beacon_get_template - beacon template generation function + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @offs: &struct ieee80211_mutable_offsets pointer to struct that will + * receive the offsets that may be updated by the driver. + * + * If the driver implements beaconing modes, it must use this function to + * obtain the beacon template. + * + * This function should be used if the beacon frames are generated by the + * device, and then the driver must use the returned beacon as the template + * The driver or the device are responsible to update the DTIM and, when + * applicable, the CSA count. + * + * The driver is responsible for freeing the returned skb. + * + * Return: The beacon template. %NULL on error. + */ +struct sk_buff * +ieee80211_beacon_get_template(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_mutable_offsets *offs); + /** * ieee80211_beacon_get_tim - beacon generation function * @hw: pointer obtained from ieee80211_alloc_hw(). @@ -3418,16 +3468,12 @@ void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets); * Set to 0 if invalid (in non-AP modes). * * If the driver implements beaconing modes, it must use this function to - * obtain the beacon frame/template. + * obtain the beacon frame. * * If the beacon frames are generated by the host system (i.e., not in * hardware/firmware), the driver uses this function to get each beacon - * frame from mac80211 -- it is responsible for calling this function - * before the beacon is needed (e.g. based on hardware interrupt). - * - * If the beacon frames are generated by the device, then the driver - * must use the returned beacon as the template and change the TIM IE - * according to the current DTIM parameters/TIM bitmap. + * frame from mac80211 -- it is responsible for calling this function exactly + * once before the beacon is needed (e.g. based on hardware interrupt). * * The driver is responsible for freeing the returned skb. * @@ -3453,6 +3499,20 @@ static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, } /** + * ieee80211_csa_update_counter - request mac80211 to decrement the csa counter + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * The csa counter should be updated after each beacon transmission. + * This function is called implicitly when + * ieee80211_beacon_get/ieee80211_beacon_get_tim are called, however if the + * beacon frames are generated by the device, the driver should call this + * function after each beacon transmission to sync mac80211's csa counters. + * + * Return: new csa counter value + */ +u8 ieee80211_csa_update_counter(struct ieee80211_vif *vif); + +/** * ieee80211_csa_finish - notify mac80211 about channel switch * @vif: &struct ieee80211_vif pointer from the add_interface callback. * @@ -4480,6 +4540,8 @@ struct rate_control_ops { void (*add_sta_debugfs)(void *priv, void *priv_sta, struct dentry *dir); void (*remove_sta_debugfs)(void *priv, void *priv_sta); + + u32 (*get_expected_throughput)(void *priv_sta); }; static inline int rate_supported(struct ieee80211_sta *sta, |
